Looking for Amplifier Installation & Accessories?

Amplifier Installation &  AccessoriesStart shopping

Cable gauge chart

How to determine the best size wire for your amplifier's power and ground

T-Spec power and ground cables

T-Spec wires and hardware ensure full current flow for your amplifier

In order to operate correctly, an amplifier needs its power and ground wiring to be large enough to accomodate its demand for electrical current. What gauge (thickness) wire to use for power cabling depends on how much current your system will try to consume, and on how long the wiring run will be.

The formula for current draw

To determine the approximate current draw (in amperes) of your amplifier (or amplifiers), you must first calculate the total power of the system (multiply the number of channels by the number of RMS watts per channel). If you have multiple amps, add up the total power figures to arrive at a grand total. Next, double your grand total power figure. Then, divide by 13.8.

Total RMS Wattage x 2 (Inverse of Amp Efficiency) ÷ 13.8 Volts = Current Draw in Amperes  (explanation below)

The resulting figure is your system's approximate maximum current draw. Compare this number to the numbers in the "Amperes" column in the chart below. Cross-reference with the cable length (the distance from your battery to the amplifier's mounting location) to determine which gauge of cable you need.

Once you have estimated the total amperage of your system using the described formula, determine the proper power and ground wire gauge from this chart based on the length of power cable your installation requires. Please note that  the smaller the gauge number, the larger the wire. 1/0 ("one-aught") is the common name for a 0-gauge wire; 2/0 ("two-aught") for a 00-gauge wire.

Cable gauge chart

A more detailed explanation

Here is an explanation about the formula we use, in case you want more details. Calculating the amplifier's total power is straightforward, but the other two parts can be confusing.

No amplifier is 100% efficient

First of all, why do we double the total power figure? That's because the typical analog amplifier is about 50% efficient. That means about half of the power it generates is turned into audio output while the other half of the power is lost as heat.

So if your amplifier is putting out 400 watts, it's actually drawing about 800 watts of power from its source, and the amp's wiring needs to be big enough to handle that draw. (Class D amplifiers are much more efficient in comparison, but it's still safest to go with the larger wire size.)

Automotive voltage is neither 12 volts nor 14.4 volts

And the 13.8? Yes, vehicles have a 12-volt electrical system, but we're assuming that the vehicle is running — which means its alternator will bump up the system voltage to about 13.8 volts. This is a better real-world representation of the vehicle's electrical supply. Dividing by 12 results in a larger number, which could point to a larger wire gauge, but it's often in the same color range in the chart. Manufacturers use 14.4 volts, when they spec their gear, to exaggerate their power ratings.

Resistance increases with length

The reason different cable lengths bear different ratings is because the electrical resistance, inherent in all wire, builds up as the cable gets longer, until it forces the voltage to drop below a useable level. At that point, up-sizing the power cable will restore the voltage to its intended level.

Size matters for current flow

Finally, according to our tech support guys, the primary performance limitation in most amplifier installations is in the current delivery — either a weak ground or insufficient wire gauge. Installing too small of a wire gauge results in poor performance, potentially shorter service life of connected components (your amplifier and speakers), and a potential safety hazard.

On the other hand, installing too large a wire gauge doesn't really have any downside, and there is the potential for better performance. Obviously, there's no need to buy 2-gauge wiring when 10-gauge will do. That kind of overkill would be a waste of money. But if the chart could lean either way between two sizes, going with the larger wire size would be the smart choice.

Gift Card The Great Gear Giveaway

Sign up for our email newsletter and then enter to win a $350 Rewards Card.