Chat
Contact us
Close contact box
Connect ID #
939 275 797 4
Connect ID #
939 275 797 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Brendan B's 2007 Chevrolet Impala

Front-to-rear audio upgrade

Brendan B. from Byron Center, MI, tells us the installation on his 2007 Chevrolet Impala LT was the second installation he's done himself, but that it was also "much harder" than his first go-round. He wanted a touchscreen radio and to retain the OEM steering wheel controls, and his Impala's factory stereo wouldn't allow him to add a subwoofer, so he decided to upgrade the whole system.

Brendan B's 2007 Chevrolet Impala

Items installed:

A feature-packed Kenwood receiver

The Kenwood DDX573BH offers a lot of sonic options, including a built-in HD Radio™ tuner and Bluetooth® streaming from compatible phones. Brendan's "I got the most features possible for my money" philosophy suits us just fine, and we think he got a tremendous value with this stereo. When asked what the first thing he shows people about this installlation is, he replied "I first show them my beautiful Kenwood receiver and all the neat things it can do."

Brendan B's 2007 Chevrolet Impala with Kenwood DDX573BH DVD receiver

module to keep his Impala's OEM steering wheel controls — it's a great accessory that works with a lot of stereos and vehicles to maintain not just steering wheel preferences but other factory enhancements. Brendan noted that it took about an hour to get the module and wiring situated behind the Kenwood, due to the tight quarters in his dash opening.

Speaker-specific situations

Next Brendan tackled his front and rear speakers. These Rockford Fosgate Punch P16 and Punch P1692 coaxials boast oversized cones for better low end, and we think Brendan invested wisely. They just look ready to rock, even before being installed:

Rockford Fosgate Punch P1692 and P16 speakers

Regarding the installation, he tells us: "The front speaker installation was relatively simple, and the only issue I had was one retaining clip broke. The rear speaker installation took a few hours of wrenching to get the seats out and panel up, but it went smoothly."

Brendan B's 2007 Chevrolet Impala with Rockford Fosgate Punch P16 2-way 6-1/2" speaker in front door

Above, we see the 6-1/2" Punch P16 sitting pretty in Brendan's front door. Below is a view of the underside of the rear deck, where we see the 6"x9" Punch P1692.

Brendan B's 2007 Chevrolet Impala with Rockford Fosgate Punch P162 6"x9" speakers in the rear deck

The way of the wiring

Once he got the stereo and speakers in place, Brendan faced a larger challenge: getting the wiring to his amplifier so he could power his subwoofers in the trunk. Brendan used 4-gauge wiring, which is on the thick side, but not unnecessarily so given the wattage requirements of the subs.

However, he ran into some issues with the Impala's firewall: "The most difficult part was trying to run 4-gauge wire through an already existing rubber grommet in the firewall on the passenger side of the car in the footwell. It took forever, in a hard to reach space, and was extremely frusturating."

Here we have the results of Brendan's hard work: a pair of booming JL Audio W0v3 12" subs in a box, nestled comfortably in the Impala's trunk. The Kicker 43CXA600 amplifier and Rockford Fosgate capacitor sit atop the enclosure, and you'll notice the 4-gauge blue wiring.

Brendan B's 2007 Chevrolet Impala with Kicker 43CXA600.1 amplifier and JL Audio 12W0V3 subwoofers in trunk

Now after Brendan's done showing people his Kenwood receiver, he can "pop the trunk and show them my subwoofers after a song or two." We think the whole ensemble is worth praising. Brendan tells us he's "pretty satisfied" with what he has so far, but he's looking to replace the tweeters in the Impala's front pillars down the line. Whatever route he chooses, we're definitely looking forward to what Brendan gets up to next.

Brendan B's 2007 Chevrolet Impala

Brendan's recent picture shows that even though he might look young, it's never too early to start as a DIY car audio enthusiast.


Vehicles in the Custom Car Showroom are submitted by customers and fans, and edited by Crutchfield writing staff. You can find more of these articles on theShowroom main page.

Please share your thoughts below.

  • Kyle clevenger from Rensselaer

    Posted on 3/1/2019

    Did you end up using the factory speaker brackets? Also where could I find the piece that the screw screws into at the top of the mounting bracket? Mine won't stay in place when the screw gets near tight resulting in a not so tightly sealer speaker

Max. 1500 characters. *Comment is required  
*Name is required  
*Email is required  
Please complete this input.  

Your email address will not be published. Comments will display after being approved by our moderators. Comments may be edited for clarity.

Looking for
car speakers?

Car Speakers Shop our selection

Find what Fits your vehicle

Remove

Checking fit...

Compare the sound