Works as advertised
Crutchfield Customer Review (What's this?)
easy to install and the hum is gone
Our experts help you pick the ideal gear for your needs.Meet our advisors
Free tech support for the life of your gear.Read about our one-on-one expert help
You may return items that are complete and like new for any reason within 60 days.See the details of our return policy
Earn one point for every dollar you spend and use those points to save on future purchases.Get full details on Crutchfield Rewards
We offer vehicle-specific installation instructions, dash kits, wiring harnesses, and speaker accessories at deeply discounted prices with car stereo and speaker purchases. Available for most vehicles.Learn more
Our customers have trusted us with their business, and they’ve helped us win awards for our service.Check out our most recent awards
The manufacturer’s warranty always applies.See more details
Item #: 003S10A
This item is no longer available.
Original Price: $14.99
American International's S-10A noise filter helps to eliminate noise that comes in through the 12-volt power line on your in-dash receiver or signal processor. Installation is simple. You have three wires to connect: one to the power line from the battery, one to the receiver's power line, and one to ground. The S-10A noise filter is recommended for audio components rated up to a total of 10 amps and 150 watts. Mounting hardware is included. Dimensions: 2-13/16"W x 1-1/2"H x 1-7/8"D. Warranty: 1 year.
easy to install and the hum is gone
I've used other noise suppressors to try and eliminate alternator whine in my system after putting in a Parrot system. Third time was the charm as I wasted money on cheaper suppressors which did not work, but American International S-10A removed all the noise just when I was losing hope.
this product works good, eliminated the noise that was coming through the ignition, I have an older car 1971 Plymouth duster
Pros: small, easy to hide in almost any spot
Put a Boss audio stereo on my Harley Heritage. It was picking up a bad hum from the engine. I installed the filter and it removed all unwanted noise.
I purchased this filter for 2 volt noise spikes (Alternator noise) on the 12v on my brake switch. This was causing my Cruise Control to intermittently drop out. These noise spikes were discovered with an oscilloscope. After installing this filter, the noise spikes were gone.
Pros: Excellent passive filter
It eliminated my engine noise. Works great
Pros: good price easy to install
Cons: most radios have two power sources constant 12v and switched. I was afraid the noise would be coming from the source I didn't filter, but I picked correctly.
My radio had a serious problem with engine noise- whining sound that would increase with RPM's. Installed this little guy and problem solved. Just like that.
Pros: Small, affordable.
Installed a 2DIN head unit (GPS, HD TV, DVD, iPhone, Bluetooth, Radio, back-up cameras & etc ) in my Toyota RV Tow vehicle the factory Toyota DVD/Tape/Radio had a whine when accelerating. The new head unit exhibited a similar whine. I ordered two filters, installed one on the 12volt main power non switched feed and a week later the second on the Accessory power feed (ignition/key switched feed) . The accessory key/ignition filter really removed the whine and high pitched engine noise. Simple install, heavy gauge pre-cut wire ready to solder. Include a cable tie and channel on the bottom of the filter for securing the cable tie to some point in your dash.
Pros: simple and it works
Cons: In order to filter the non-switched 12volt and the 12volt ignition accessory feed requires two filters-but that's life if you want to isolate ignition noise
Worked like a charm. This saved me from having to tear apart my whole dash looking for "interference" in the electronic components of the car.
Pros: Works. Cheap.
Engine Noise: Noise, caused by the vehicle's engine, can enter your stereo system in one of two ways: through the power source and through the antenna. This noise increases and decreases with speed. This filter eliminates engine noise coming through the power source.
Note: For noise entering through the antenna, you should install an Antenna Noise Filter (see item # 003AS100).
Multiple Applications: This noise filter (S-10-A) can be used for all audio components in your vehicle, including receivers, equalizers, tape players, CD players, CD changers, or small amplifiers.
Capacity: The S-10A noise filter is recommended for audio components rated up to 10 Amps and 150 watts.
Easy Installation: The filter can be mounted to a flat surface using the supplied mounting screws and mounting plate. You can also mount the filter using the supplied 10" wire tie. The filter features three wires that need to be spliced into the power and ground wires leading to the component. The red wire connects to the fused power wire leading to the radio. The blue wire connects to the power lead of the receiver (or component), and the black wire is connected to ground. The filter is most effective when mounted close to the radio.
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.