Boston Acoustics GT-2200

2-channel car amplifier — 200 watts RMS x 2

  • Boston Acoustics GT-2200


  • Boston Acoustics GT-2200


Crutchfield OMC logo
We don't check this item for fit or compatibility.
Item #: 065GT2200

Review Summary

This item is no longer available to purchase.
Contact us for other options
Call   Email  
Original price $199.99
We recommend this similar item, or shop all All Car Amplifiers

Our take on the Boston Acoustics GT-2200

by Buck Pomerantz
Boston Acoustics

My system has plenty of power. Who needs an amp?

You might think you don't need an amp because you have a 400-watt system in your car, or because your new stereo puts out 50 watts a channel. But those are peak wattage ratings, which may boil down to 15 or 20 watts per channel, using the more realistic RMS rating. An amp sends your speakers the power they need to deliver your music with clarity and impact, whether you're using factory speakers or high-performance components. And low-frequency reproduction requires lots of power, so an amp is an absolute must if you're adding a sub to your system.

High Power at Low Impedance

Three stage cooling Boston Acoustics builds versatility and power into their GT Reference Series amps, so they'll deliver clean, dynamic performance in any kind of system. A high-current design combines with highly efficient output transistors to allow these amps to drive low-impedance loads safely, so you can get more out of your system.

Drive speaker set or sub

The GT-2200 puts out 200 watts RMS per channel to a pair of speakers, and Q-Tune™ technology lets you adjust the sound of your full-range speakers to blend in better with your subwoofer. In single-channel mode, you can send up to 900 watts RMS to a subwoofer — plenty of juice to give your music tremendous impact.

Advanced electronics

Boston Acoustics uses high-quality components that allow this amp to respond with lightning speed — you'll really notice the difference with percussive sounds like drums and piano. A computer-controlled diagnostic system monitors and protects against overheating, excessive voltage, and short circuits, so you'll get years of dependable musical enjoyment out of this amp.

High-quality internal components

Read more


  • 2-channel car amplifier
  • 200 watts RMS x 2 at 4 ohms (350 watts RMS x 2 at 2 ohms)
  • 1-ohm stable in stereo mode (450 watts RMS x 2 at 1 ohm)
  • 700 watts RMS x 1 bridged output at 4 ohms (900 watts RMS x 1 at 2 ohms)
  • CEA-2006 compliant
  • variable high-pass filter (20-350 Hz, 12 dB/octave)
  • variable low-pass filter (50-250 Hz, 12/24 dB/octave)
  • Q-Tune technology for crossover adjustment
  • cooling fan
  • frequency response: 10-95K Hz
  • preamp-level inputs
  • fuse rating: 70A x 1
  • 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • adjustable mounting feet
  • 18-5/8"W x 2-3/8"H x 9"D
  • warranty: 1 year
  • Our 60-day money-back guarantee

Hands-on research from the Crutchfield Labs (what are the Labs?)

Features and Specs
RMS Power Output (Watts x Channels) 200 x 2
Peak Power Output (Watts x Channels) N/A
Power at 2 Ohms (Watts x Channels) 350 x 2
Bridged Power (Watts x Channels) 700 x 1
Minimum Impedance Bridged 2
Minimum Impedance Unbridged 1
Best Frequency Response 10-95k Hz
THD at Rated RMS Power 1%
Signal to Noise Ratio 100 dB
Input Voltage 14.4v
Amplifier Class AB
Low-Pass Crossover Frequency 50-350
Low-Pass Slope (dB/octave) 12, 24 dB/oct
High-Pass Crossover Frequency 20-350
High-Pass Slope (dB/octave) 12 dB/oct
Bass Boost No
Bass Boost Frequency N/A
Fan Cooled Yes
Fuse Rating 70 x 1 (AFS)
Speaker Level Inputs No
Preamp Outputs No
Width (inches) 18-5/8
Height (inches) 2-3/8
Depth (inches) 9
Parts Warranty 1 Year
Labor Warranty 1 Year
Product Research
What's in the box?

Download owner's manual

  • 2-Channel amplifier with a 70-amp AFS fuse installed
  • 4 Self-tapping screws (4mm x 20mm)
  • 3mm Hex wrench
  • 2mm Hex wrench
  • 0.250 Female quick-slide
  • Owner's Manual (English)
  • Owner's Manual (Spanish)

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.



GT-series Amplifiers: The Boston Acoustics GT-2200 amplifier is part of the GT-series of amplifiers, which feature high efficiency and output stages that deliver increased power into lower impedances, and maximum dynamics and transient response. The advanced fan cooling system allows you to mount the GT-series amps in varied positions. The low profile design and adjustable mounting feet make installation in tight locations much easier.

1-Ohm Stable: The GT-2200 can be connected to loads with impedances as low as 1 Ohm stereo or 2 Ohms mono. The lower the impedance, the higher the output power:

  • 200 watts x 2 @ 4 ohm stereo
  • 350 watts x 2 @ 2 ohm stereo
  • 450 watts x 2 @ 1 ohm stereo
  • 700 watts x 1 @ 4 ohm mono
  • 900 watts x 1 @ 2 ohm mono

Top-mounted AFS Fuse: The amp is equipped with a 70-amp AFS-type fuse, located on the top panel under the removable cover. The fuse is held in place by 2 Phillips-head screws.

Adjustable Mounting Feet: The mounting feet on the GT-2200 can slide along the front and rear edges, allowing you to adjust the mounting points of the amplifier. The feet can adjust between 3/4" and 16-1/8".


Top-mounted Controls: The amplifier has controls conveniently mounted on the top panel under a removable cover. The controls include:

  • Signal: This 2-way switch allows you to choose the type of input signal: "Stereo" or "Mono" (if "Mono" is selected, the left channel input only is used)
  • GT-RSL: This 2-way switch allows you to turn on or off the optional Remote Subwoofer Level Controller (item # 065GTRSL--see below).
  • Low-pass Filter: The amp has a rotary control to select the cutoff frequency between 50 Hz and 350 Hz. In addition, a 3-way switch lets you select a slope of 12 dB/octave stereo, 12 dB/octave mono, or 24 dB/octave mono. A second 2-way switch lets you turn the low-pass filter "On" or "Off".
  • High-pass Filter: Using the rotary control, you can select a cutoff frequency between 20 Hz and 350 Hz. A 2-way switch allows you to turn the high-pass filter On or Off.
  • Q-Tune: Once the high-pass crossover point has been determined, you can use the rotary Q-Tune control to increase the bass information centered around the crossover point.
  • Input Sensitivity: You can adjust the level of the input signal with this rotary control. Range is 0.2 Volts to 8.0 Volts.

Remote Subwoofer Level (GT-RSL): The GT-2200 has a front-mounted port for connecting the optional GT-RSL Remote Subwoofer Level Controller for GT Amplifiers (065GTRSL, sold separately). When the GT-RSL is connected and switched on, you can control the level of the subwoofer independent of the main sound system volume control. The GT-RSL has a 4-meter cable and a dash-mountable rotary control knob.


Front-mounted Terminals: The GT-2200 has all of the cable connections on the front of the amplifier for a clean installation. The terminals include:

  • Input: Left and right RCA jacks for the input signal from the head unit.
  • Remote: A 0.25" male quick slide for connecting the remote turn-on lead from the head unit. A 0.25" female quick slide is included for terminating your remote lead.
  • GT-RSL: A multi-pin port, covered by a removable plate, for connecting an optional GT-RSL Remote Subwoofer Level Controller (065GTRSL).
  • Speaker Outputs: Two pairs of set-screw terminals are provided for connecting a pair of speakers. The terminals can accept up to 12-gauge wire. The set screws can be tightened/loosened with the supplied 2mm Hex wrench. Note: You must first remove the top cover in order to access the set screws for the speaker and power terminals.
  • Power Input: Two set-screw terminals are provided for connecting the power and ground cables. The terminals can accept up to 4-gauge wire, and 4-gauge wire is recommended. The set screws can be tightened/loosened with the supplied 3mm Hex wrench.
Review this product
Great Gear Giveaway rewards card

Submit a review and then enter to win a $500 rewards card

Boston Acoustics GT-2200 Reviews

Average Customer Review:

2 people say:

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left
Filter by rating:
2 out of 5

do not run subs with this amp

Written By Rob, kona, HI on Friday, September 21, 2012
Was great but now goes in to protect at any ohm load even connected to tweeters?!?!!!
Sq, power, great x-over
Overheats will fry and can't handle subs
1 out of 4 people found this helpful
Was this review helpful?    Yes | No
5 out of 5

Top Notch

Written By Rob, Kona, HI on Monday, April 23, 2012
Crutchfield Customer Review (What's this?)
My expectations because of my previous experience with Boston products was very high for this amp. I have a Boston Factory system in my other car as well as owning a pair of Boston 5x7's.

I have this amp 2 ohms Mono on a pair of Polk DB1240's in a sealed box in my trunk of my Mazda 3 sedan, the gain is set at half. The sound quality is very good. You can hear the not only the thud that is required to get that sub bass punch/hit but also hum that is required for good midbass sound. It also is powerful and loud enough to satisfy my inner bass head while hitting every single note crisp.

Despite having it hooked up with 4 gauge power and ground and a Tsunami 1.2 farad capacitor it still does run pretty hot (if you push it and it gets LOUD) but never cut off on me yet. It has a buit-in fan which in my setup is inaudible. It also doesnt seem to dim my headlights as much my old Class D monoblock did. It looks very nice but is on the large size but you can move the mounting feet so that helps.

I don't think there is a better amp out there for this price with the sound qualitty, flexibility and power you get from the GT-2200
Sound Quality, Controls,ability to drive low impedences, mounting feet, wiring options
Size, runs really hot
7 out of 9 people found this helpful
Was this review helpful?    Yes | No

Add accessories for the Boston Acoustics GT-2200

You'll need an amp wiring kit to install your new amplifier, as wiring is not included. See all categories & accessories

EFX PA4BX Wiring Kit 4-gauge amplifier wiring kit — includes 2-channel patch cable
4 people say
Your Price: $79.99
Add to Cart
Rockford Fosgate RFK4 4-gauge amplifier power wiring kit
10 people say
Your Price: $114.99
Add to Cart
Rockford Fosgate RFK4X Complete 4-gauge amplifier wiring kit
Includes patch cable and speaker wire
12 people say
Your Price: $159.99
Add to Cart
T-Spec 16-gauge Speaker Wire Black/white jacket — priced per foot
13 people say
Your Price: $0.69
Add to Cart
T-Spec 12-gauge Speaker Wire Black/white jacket — priced per foot
29 people say
Your Price: $1.99
Add to Cart
Stinger PRO Series Speaker Wire Priced per foot (16 Gauge)
50 people say
Your Price: $0.39
Add to Cart
T-Spec 2-Channel RCA Patch Cables Available in 7 different lengths (17-foot)
25 people say
Your Price: $19.99
Add to Cart
54 people say
Your Price: $7.99

After $2.00 Price Break

Add to Cart
EFX CFHG4 Fuse Holder In-line AGU fuse holder accepts 4- to 8-gauge wire
Your Price: $9.99
Add to Cart
Rockford Fosgate RFFAGU Fuse Holder Platinum-plated AGU fuse holder
Fits 4- or 8-gauge cable
25 people say
Your Price: $10.99
Add to Cart
T-Spec Capacitor 1.5-farad capacitor with red LCD meter
11 people say
Your Price: $79.99
Add to Cart
S&G Wire Cutter/Stripper Tool Cuts and strips 12- to 22-gauge wire
15 people say
Your Price: $19.99
Add to Cart
S&G Tool Aid 87650 Door Trim and Panel Removal Tool
67 people say
Your Price: $9.99
Add to Cart
Pro.Fit Wire Worm Installation tool helps route wiring through tight spaces
31 people say
Your Price: $12.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
52 people say
Your Price: $24.99
Add to Cart
Skewdriver Pro SPK4042 Ratcheting straight and offset screwdriver set with 40 bits (Skewdriver Pro with ratchet handle, pictured)
8 people say
Your Price: $49.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
2 people say
Your Price: $29.99
Add to Cart
InstallCard: Amp or Equalizer Prepaid professional amplifier or EQ installation
17 people say
Your Price: $79.99
Add to Cart

Why choose SquareTrade?

The #1-Rated Protection Plan

Thousands of people have reviewed SquareTrade Protection Plans — and made us #1.

5-Day Service Guarantee & Free Shipping

We'll repair or replace your item in five business days or less after we've received it, or your plan is free. And, as always, we pay for all shipping.

Protection from Normal, Everyday Use

Repairing your average mechanical or electrical failure can cost as much as buying a new device. With SquareTrade, you're covered — including parts and labor.

3 Year Protection Plan
3 Year Protection Plan
Your Price: $29.99
Add to Cart

For a more in-depth review and enhanced detailed information on the Boston Acoustics GT-2200, please visit the Crutchfield website product page (/ISEO-rccbcspd/p_065GT2200/Boston-Acoustics-GT-2200.html ).