1.888.955.6000
crutchfield.com
Crutchfield

Focal FPS 4160

4-channel car amplifier — 120 watts RMS x 4

Save 50% on a select amp wiring kit with any $249+ car amplifier with any $249+ car amplifier
Zoom
  • Focal FPS 4160

    Front

  • Focal FPS 4160

  • Focal FPS 4160

    Remote

Crutchfield OMC logo
We don't check this item for fit or compatibility.
 

Our take on the Focal FPS 4160

by Buck Pomerantz
Focal

My system has plenty of power. Who needs an amp?

You might think you don't need an amp because you have a 400-watt system in your car, or because your new stereo puts out 50 watts a channel. But those are peak wattage ratings, which may boil down to 15 or 20 watts per channel, using the more realistic RMS rating. An amp sends your speakers the power they need to deliver your music with clarity and impact, whether you're using factory speakers or high-performance components. And low-frequency reproduction requires lots of power, so an amp is an absolute must if you're adding a sub to your system.

Focal Power Symmetric Amplifiers

Focal studied the interaction between speakers and amplifiers so that their FPS Series amps can make your speakers sound their absolute best. Focal makes no compromises when it comes to the design and internal components in their amplifiers, so you'll get reliable, high-fidelity reproduction for your music.

FPS 4160

Versatility

The FPS 4160 4-channel amplifier sends 120 watts RMS per channel to your front and rear pairs of full-range speakers or components. You can use this versatile amp to power four 2-ohm subs with 200 watts RMS each, or switch to 2-channel mode and drive a pair of subs with 380 watts RMS each. You can even power your front speakers with two of the amp's channels while bridging the rear channels to drive a single sub. High-pass, low-pass, and band-pass filtering adjusts the output to match a wide variety of speakers, components, and sub combinations. And a wired remote level control for the rear cahannels give you even more control over your subs' performance.

Pure signal, superior sound

The dual power supply in the FPS 4160 uses a unique circuit design to ensure stable performance under any conditions. A heavy heatsink with a thermostat-controlled, progressive-speed fan keeps all the parts running cool. Focal's engineers stripped all signal paths of side-tracking circuits, so your music makes its way through the amp with maximum fidelity and minimum interference. Dynamic soft clipping allows an ultra-clean signal to pass to your subs while protecting them from destructive "clipped" distortion.


FPS High Cap

Plug-in capacitors

Optional High Cap outboard capacitor modules plug directly into the amp, smoothing out any power fluctuations caused by sudden system demands, so you enjoy consistent, superb sound quality. The FPS 4160 amplifier accepts two High Cap modules, one for each section of the dual power supply.


FPS 4160 rear panel
See more info on this item

Highlights:

  • 4-channel car amplifier
  • 120 watts RMS x 4 at 4 ohms (200 watts RMS x 4 at 2 ohms)
  • 380 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
  • CEA-2006 compliant
  • variable high- and low-pass filters (50-500 Hz or 500-5K Hz)
  • variable band-pass filter (50-500 Hz, 500-5K Hz)
  • Class-AB amplifier design
  • thermostat-controlled, progressive-speed cooling fan
  • remote level control (channels 3-4)
  • optional High Cap outboard capacitor modules increase power efficiency
  • frequency response: 10-52,000 Hz
  • preamp inputs
  • 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • fuse rating: 40A x 2
  • 16-7/8"W x 2-3/8"H x 10-3/4"D
  • warranty: 1 year
  • Our 60-day money-back guarantee

Hands-on research from the Crutchfield Labs (what are the Labs?)

Features and Specs
Performance
RMS Power Output (Watts x Channels)
Loading...
120 x 4
Peak Power Output (Watts x Channels)
Loading...
N/A
Power at 2 Ohms (Watts x Channels)
Loading...
200 x 4
Bridged Power (Watts x Channels)
Loading...
380 x 2
Minimum Impedance Bridged
Loading...
4
Minimum Impedance Unbridged
Loading...
2
Best Frequency Response
Loading...
10-52K Hz
THD at Rated RMS Power
Loading...
1%
Signal to Noise Ratio
Loading...
92 dB
Input Voltage
Loading...
14.4v
Features
Amplifier Class
Loading...
AB
Low-Pass Crossover Frequency
Loading...
50/500Hz/500-5k
Low-Pass Slope (dB/octave)
Loading...
12 dB/oct
High-Pass Crossover Frequency
Loading...
50-500Hz/500-5k
High-Pass Slope (dB/octave)
Loading...
12 dB/oct
Bass Boost
Loading...
No
Bass Boost Frequency
Loading...
N/A
Fan Cooled
Loading...
Yes
Fuse Rating
Loading...
80
Speaker Level Inputs
Loading...
No
Preamp Outputs
Loading...
No
Width (inches)
Loading...
16-7/8
Height (inches)
Loading...
2-3/8
Depth (inches)
Loading...
10-3/4
Parts Warranty
Loading...
1 Year
Labor Warranty
Loading...
1 Year
Product Research
What's in the box?

Download owner's manual

  • 4-Channel amplifier (with two 40A Maxi fuses inserted in chassis)
  • 2 Spare 40A Maxi fuses
  • Bass Knob
  • 16' Remote cable (terminated by RJ-14 connectors)
  • 4 Long mounting screws
  • 2 Short mounting screws
  • 4 Flat-washers
  • 4 Lock-washers
  • Hex-key
  • User Manual (Eng/Fre)

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Features
Controls
Connections

Features

AB-Class Amplifier Design: The Focal FPS 4160 amplifier features an AB-class amplification design for excellent sound quality.

Symmetrical Design: The Focal FPS 4160 utilizes dual mono symmetric construction (PCB circuits in perfect mirror-image) that clearly increase the independent performance of each of the amplifier's channels, while improving the staging and the stereo disassociation.

Channel Design: The Focal FPS 4160 can be configured as a 4-channel, 3-channel, or 2-channel amplifier. The amplifier is stable down to 2-ohms in stereo, and 4-ohms when bridged.

CEA 2006 Compliant: The FPS 4160's power ratings are measured according to the strict standards dictated by the Consumer Electronics Association (CEA). These standards allow you to accurately compare the rated power output of all CEA 2006-compliant amplifiers, even if they come from different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging.

  • CEA 2006 Rating: 120 watts x 4-channel in 4-ohms @ 20 to 20,000 Hz with 1% THD+N

2-Ohm Stable: The amplifier is stable down to 2-ohms in stereo, and 4-ohms when bridged.

  • 2-Ohm Rating: 200 watts x 4-channel in 2-ohms @ 1kHz with 0.07% THD
  • Bridged (4-ohm): 380 watts x 2-channel in 4-ohms @ 1kHz with 0.08%

Soft-Clipping: The amplifier's dynamic soft clipping feature protects your connected speakers from distortion.

Controlled Cooling System: The Focal FPS 4160 utilizes a progressive controlled cooling system to regulate the amplifier's temperature by controlling air flow through an active fan and integrated cooling fins. Even before the thermo-regulated 3-1/8" low-noise cooling fan begins rotating at 122°F, the "T" shape of the amplifier's cooling fins permits 17% of active surface heat dissipation while guaranteeing extreme rigidity to the chassis.

Note: The cooling system only works when the amplifier temperature exceeds 122°F. The rotation speed of the cooling system depends on the amplifier's temperature.

Protection Circuitry: The Focal FPS 4160 amplifier employs the following protection circuits- short circuit, thermal overload, over voltage, polarity reversal.

LED Indicators: The green LED "Power" indicator means the amplifier is on and operating properly. The red LED "Protect" indicator  means that the amplifier has shut-down and is under protection.

Anti-vibration Feet: The Focal amplifier is equipped with four integrated damping rubber feet to resist vibration.

High-Cap Compatible (optional): The optional Focal High-Cap (091FPSCAP, sold separately) is an external power supply module. Once connected to the Focal amplifier, it increases the amplifier's power supply. The resulting benefit is a higher-fidelity audio signal from the Focal amplifier and overall better music performance, with enhanced dynamic behavior, improved speaker control and punchier bass.

Note: The FPS 4160 requires two Focal High-Caps.

Controls

Front-mounted Controls: The amplifier has controls conveniently mounted on the front panel.

Gain Control: You can adjust the level of the input signal for the front and rear channels of the amplifier independently. Range is 0.2 Volts to 5.0 Volts.

Fader Switch: A two-way switch for configuring the amp for two-channel or four-channel inputs. If you have a 4-channel input signal, you should push in the fader switch so you can fade from front to back using the head unit fader. If you have only a two-channel input signal, the switch should be in the Off position so all 4 channels of the amplifier can be fed with the 2-channel input signal, with no fading available.

Crossover Switch: This 3-way switch lets you select the crossover operation for the front and rear channels of the amplifier independently. You can choose from High-pass, Band-pass, or Low-Pass

Frequency: Using this rotary control, you can select a cutoff frequency (50-500 Hz or 500-5,000 Hz) for the front and rear crossovers. The crossovers have a slope of 12 dB/octave.

Direct Mode: You can defeat the crossovers for the amplifier's front and rear channels, so that the audio signal of the Focal FPS 4160 is directly amplified without any crossover adjustments.

Wired Bass Knob: The Focal FPS 4160 comes with a wired bass-level control knob. The bass-level is adjustable from -9 to +9 dB. The bass-level knob also features a mute button to completely attenuate the audio coming from the amplifier. The bass-level knob features integrated flanges and comes with two screws to mount the unit under the dash. It includes a 16' cable to connect to the amplifier.

Note: The wired remote measures 2.625" (w) x 1.0625 (h) x 2.4375" (d)

Connections

Front-mounted Terminals: The Focal FPS 4160 has all of the cable connections on the front of the amplifier for a clean installation.

Power Input: Two set-screw terminals are provided for connecting the power and ground cables. The terminals can accept up to 2-gauge wire, however, a 4-gauge wiring kit is sufficient for the 60-amp rating of the built-in fuse. The set screws can be tightened/loosened with the supplied Hex wrench.

Remote Turn-on: A set screw terminal for connecting the remote turn-on lead. The terminal will accept up to 10-gauge wire. The set screw can be tightened/loosened with the supplied Hex wrench.

Speaker Outputs: 4 pairs of set-screw terminals are provided for connecting speakers. The terminals can accept up to 8-gauge wire. The set screws can be tightened/loosened with the supplied Hex wrench.

Pseudo-Balanced Inputs: The amplifier is equipped with two pair of left & right gold-plated RCA jacks (front/rear) for the input signal from the head unit. These pseudo-balanced inputs help to reject ground noise.

Remote Control: An RJ-14 jack for connecting the supplied remote bass control module.

Maxi Fuses: The amp is equipped with two 40-amp Maxi fuses. Two spare fuses are included with the amplifier.

 

Product reviews from the Crutchfield Labs (what are the Labs?)

Video: Focal FPS Amplifiers

Video: Focal FPS Amplifiers

by Zak Billmeier
 
Video: Focal FPS Amplifiers

For the best amplified sound in your car, turn to Focal. This brief video introduces the Focal FPS series of amplifiers.

 
Be the first to review this product
Great Gear Giveaway rewards card

Submit a review and then enter to win a $500 rewards card

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left

Add accessories for the Focal FPS 4160

You'll need an amp wiring kit to install your new amplifier, as wiring is not included. See all categories & accessories

EFX PA4BX Wiring Kit 4-gauge amplifier wiring kit — includes 2-channel patch cable
1 person says
Your Price: $79.99
Add to Cart
Kicker PK4 4-gauge amplifier power wiring kit
Your Price: $129.99
Add to Cart
Rockford Fosgate RFK4 4-gauge amplifier power wiring kit
10 people say
Your Price: $114.99
Add to Cart
Rockford Fosgate RFK4X Complete 4-gauge amplifier wiring kit
Includes patch cable and speaker wire
12 people say
Your Price: $159.99
Add to Cart
T-Spec 16-gauge Speaker Wire Black/white jacket — priced per foot
11 people say
Your Price: $0.69
Add to Cart
T-Spec 12-gauge Speaker Wire Black/white jacket — priced per foot
27 people say
Your Price: $1.99
Add to Cart
Stinger PRO Series 16-gauge Speaker Wire Black jacket — priced per foot
46 people say
Your Price: $0.39
Add to Cart
T-Spec 2-Channel RCA Patch Cables Available in 7 different lengths (20-foot)
23 people say
Your Price: $20.99
Add to Cart
7 people say
Your Price: $29.99
Add to Cart
52 people say
Your Price: $9.99
Add to Cart
EFX CFHG4 Fuse Holder In-line AGU fuse holder accepts 4- to 8-gauge wire
Your Price: $9.99
Add to Cart
Rockford Fosgate RFFAGU Fuse Holder Platinum-plated AGU fuse holder
Fits 4- or 8-gauge cable
25 people say
Your Price: $10.99
Add to Cart
Focal FPS High Cap Single plug-in capacitor module for FPS Series amps
1 person says
Your Price: $99.99
Add to Cart
T-Spec Capacitor 1.5-farad capacitor with red LCD meter
9 people say
Your Price: $79.99
Add to Cart
Metra Crimp Tool and Connectors Package contains crimp tool and over 150 pieces
15 people say
Your Price: $19.99
Add to Cart
S&G Wire Cutter/Stripper Tool Cuts and strips 12- to 22-gauge wire
14 people say
Your Price: $19.99
Add to Cart
S&G Tool Aid 87650 Door Trim and Panel Removal Tool
66 people say
Your Price: $9.99
Add to Cart
Pro.Fit Wire Worm Installation tool helps route wiring through tight spaces
28 people say
Your Price: $12.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
51 people say
Your Price: $24.99
Add to Cart
Skewdriver Pro SPK4042 Ratcheting straight and offset screwdriver set with 40 bits (Skewdriver Pro with ratchet handle, pictured)
8 people say
Your Price: $49.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
2 people say
Your Price: $29.99
Add to Cart
DEI Heat Shrink Tubing Black 4-foot length (Assortment)
6 people say
Your Price: $24.99
Add to Cart
Your Price: $69.95

After $10.00 Price Break

Add to Cart

Why choose SquareTrade?

The #1-Rated Protection Plan

Thousands of people have reviewed SquareTrade Protection Plans — and made us #1.

5-Day Service Guarantee & Free Shipping

We'll repair or replace your item in five business days or less after we've received it, or your plan is free. And, as always, we pay for all shipping.

Protection from Normal, Everyday Use

Repairing your average mechanical or electrical failure can cost as much as buying a new device. With SquareTrade, you're covered — including parts and labor.

3 Year Protection Plan
3 Year Protection Plan
Your Price: $179.99
Add to Cart
4 Year Protection Plan
4 Year Protection Plan
Your Price: $224.99
Add to Cart

For a more in-depth review and enhanced detailed information on the Focal FPS 4160, please visit the Crutchfield website product page (/ISEO-rccbcspd/p_091FPS4160/Focal-FPS-4160.html ).