About the Focal FPX 2.750
Power-packed
Power-packed
Focal's FPX 2.750 amplifier delivers 220 watts RMS per channel in 2-channel mode, or up to 770 watts RMS when it's bridged in mono operation. This impressive power comes from a compact chassis that's a little smaller than one of my Size 10 bedroom slippers, so it'll probably fit just about anywhere in your vehicle. Focal's engineers designed this amp to reproduce your music with unerring precision, so it'll pair up nicely with a high-performance component system or a couple of subs.
Tone controls for speakers and subs
High- and low-pass filters let you optimize the signal for the best tone without distortion. When you're powering a subwoofer, the subsonic filter tames any wild rumbling, while the bass boost sets it loose when you want it. Focal includes a wired remote so you can adjust the bass level from your front seat.
Focal FPX 2.750 input and control panel
Product highlights:
- 2-channel car amplifier
- 220 watts RMS x 2 at 4 ohms (385 watts RMS x 2 at 2 ohms)
- 770 watts RMS x 1 bridged at 4 ohms (4-ohm stable when bridged)
- CEA-2006 compliant
- full-range Class-D amplifier design
- variable high- and low-pass filter (50-500 Hz, 12 dB/octave)
- variable subsonic filter (20-50 Hz, 24 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- wired remote level control included
- preamp inputs and outputs
- frequency response: 20-20,000 Hz
- fuse rating: 30A x 2
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 9-3/8"W x 2-1/8"H x 5-1/4"D
- warranty: 1 year
- MFR # FPX 2.750
What's in the box:
Focal FPX 2.750 owner's manual
- 2-Channel amplifier
- FPX Remote Control
- 16.5' Remote control cable (RJ14 modular plugs on both ends)
- Six 30-amp ATM fuses (3 installed/3 spare)
- 2mm Allen wrench
- 4mm Allen wrench
- Four M4 x 65mm Allen-head screws
- 2 Self-tapping screws (M4 x 15mm)
- User Manual
See the difference between "Open Box" and "Scratch & Dent" Outlet items
Customer reviews for Focal FPX 2.750
Loading...
Loading reviews...
Average review:
4.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Focal FPX 2.750
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
220 x 2 | |
Peak Power Output (Watts x Channels) | N/A | |
Power at 2 Ohms (Watts x Channels) | 385 x 2 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 770 x 1 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-20k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 76 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-500 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | 50-500 Hz | |
High-Pass Slope (dB/octave) | 12 dB/oct | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 48 Hz | |
Fan Cooled | No | |
Fuse Rating | 90 | |
Speaker Level Inputs | --- | |
Preamp Outputs | 1 pair | |
Width (inches) | 9-3/8 | |
Height (inches) | 2-1/8 | |
Depth (inches) | 5-1/4 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Features
Controls
Connections
Specifications
Features
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare amplifiers on an equal basis.
Amp Overview: The Focal FPX 2.750 is a full-range Class D 2-channel amplifier. Class D amplifiers are compact, but very powerful. Its Class D design and thick aluminum chassis (3/8" on top, 11/16" on the sides) offer efficient dissipation of heat for reliable performance. The amp can be configured for two-channel or mono operation. It has a built-in crossover that can be configured for low-pass, high-pass, or full-range application, and a subsonic filter. The FPX 2.750 comes with a wired remote with a 16.5' cable.
Power Output: The amplifier has the following power output:
- 220 watts RMS x 2 at 4 ohms
- 385 watts RMS x 2 at 2 ohms
- 770 watts RMS x 1 at 4 ohms bridged
Compact Footprint: The Focal FPX 2.750 comes with 2-1/2" long mounting screws that secure the amplifier without external mounting tabs. The mounting holes are placed inside of the amp's 9-3/8" x 5-1/4" footprint and extend the entire thickness of the amp.
Protection Circuits: The amplifier is equipped with protection circuits for the following: short circuits, low impedance, power drop, thermal overload, reversed polarity, or DC offset.
Controls
Level Control (Gain): The Focal FPX 2.750 is equipped with line level inputs. The input level range is 0.2 Volts to 5.0 Volts. There is a rotary gain control that can be adjusted by a standard flat-head or Phillips screwdriver (not supplied).
Selectable Crossover: The amp features a high-quality crossover that can be configured as Low pass, High pass, or Full-range. It has a variable cutoff frequency from 50Hz to 500Hz, with a slope of 12 dB per octave.
Subsonic Filter: In addition to the selectable crossover, the amp has a subsonic filter that eliminates extremely low frequencies that cause distortion and that speakers typically can't handle. The 20-50 Hz subsonic filter has a slope of 12dB per octave.
Bass Boost: The amp features a bass boost circuit that is variable from 0 to 12dB, with a center frequency of 48 Hz.
Connections
Power Input: Two set-screw terminals are provided for connecting the power and ground cables. The terminals can accept up to 4-gauge wire. The set screws are tightened/loosened with the included 4mm Allen wrench.
Fuses: The amp comes with six 30-amp ATM (mini-blade) fuses; three are installed internally, and the others are replacements. The bottom panel is removed to replace the fuses. A 90-amp fuse (minimum) should be installed on the power wire within 18" of the battery.
Remote Turn-on: The remote turn-on set screw terminal will accept up to 12-gauge wire. The set screw is tightened/loosened with the included 2mm Allen wrench.
Speaker Outputs: The amplifier includes two pairs of speaker output terminals. Markings are provided for bridged connections. The set-screw terminals will accept up to 12-gauge wire and are tightened/loosened with the included 2mm Allen wrench.
Signal Input: The amplifier features a pair of stereo RCA inputs for connecting the input signal from the source unit to the amp via RCA cables.
Signal Output: In addition to the line outputs, the FPX 2.750 has a set of line outputs that can send the audio signal to a second amplifier.
Specifications
- Frequency Response: 20Hz - 20kHz
- Total Harmonic Distortion: 0.01%
- Signal-to-Noise Ratio: >76dBA
- Crosstalk (1 kHz): >72dB
- Standby Current: 1.1A
- Dimensions: Width 9.355" Height 2.079" Depth 5.223"
- Weight: 4.4 pounds
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...