About the JBL GTO-1001EZ
JBL's compact GTO-1001EZ amplifier will drive your subs with up to 1,000 watts RMS, bringing exciting, visceral impact to the music in your car. This mono amp looks very cool with its "old-school" styling, and JBL includes a few innovations that really separate this amp from the others.
Efficient bass power always set correctly
JBL's compact GTO-1001EZ amplifier will drive your subs with up to 1,000 watts RMS, bringing exciting, visceral impact to the music in your car. This mono amp looks very cool with its "old-school" styling, and JBL includes a few innovations that really separate this amp from the others.
Simple Setup System for setting amp gain
One of the biggest problems with installing an amplifier is setting the gain properly. JBL has come up with a fool-proof method for getting it right, ensuring full-power performance and distortion-free play. Using test tones on the included setup CD, you adjust the gain knob until the yellow light or the red light goes off, and the green "Gain OK" light comes on it's that simple. You'll never have to worry again about your amp "clipping" the signal, and possibly damaging your speakers or subs.
Plays well with factory radios
This GTO amp comes with screw-on bare wire-to-RCA adapters that let you hook up the amp, using your car's factory speaker wiring to supply the input signal. In some vehicles, the factory radio shuts down when you try to tap into the speaker wires, displaying a "no speakers are present" message. This amp features a special circuit that fools those factory radios by simulating a speaker load. The onboard crossovers and bass boost let you fine tune the system to perfection, and the large recessed knobs mean you don't need a tiny screwdriver to make your adjustments.
Confused about impedance? Check out our article on matching subs and amps.
Product highlights:
- mono subwoofer amplifier
- 650 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- frequency response: 10-280 Hz
- Class D amp technology
- variable low-pass filter (40-280 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- Simple Setup System with test tone CD for perfect gain setting
- optional wired remote level controller available soon
- preamp and speaker-level inputs (speaker wire-to-RCA adapters included)
- switchable automatic signal-sensing turns on amp without need for remote lead
- fuse rating: 40A x 3
- 6- or 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 14-11/16"W x 2-5/8"H x 9-11/16"D
- warranty: 1 year
- MFR # GTO-1001EZ
What's in the box:
- Mono subwoofer amplifier
- Three 40-amp ATO fuses (installed)
- 2 Speaker wire to RCA adapters
- Setup CD
- Warranty information
- Owner's manual (English/ German/ French/ Spanish/ Dutch/ Italian/ Swedish/ Danish/ Finnish/ Korean/ Japanese/ Chinese/ Russian/ Polish/ Portuguese/ Turkish/ Indonesian)
Customer reviews for JBL GTO-1001EZ
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the JBL GTO-1001EZ
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
650 x 1 | |
Peak Power Output (Watts x Channels) | 1450 x 1 | |
Power at 2 Ohms (Watts x Channels) | 1000 x 1 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-280 Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 80 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 40-280 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 45 Hz | |
Fan Cooled | No | |
Fuse Rating | 120 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 14-11/16 | |
Height (inches) | 2-5/8 | |
Depth (inches) | 9-11/16 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Features
Setup Disc: The included setup CD is used to optimize the input gain. A test tone is output from the disc and the Gain LEDs on the amp (green, yellow, red) guide you through adjusting the gain controls.
Note: The instructions in the first version of the manual indicate the radio should be at full volume when playing the setup disc; this is wrong and JBL is in the process of correcting the manual. The volume should actually be as high as possible without distorting the signal; this will be different for every radio, but approximately 3/4 volume is typical.
Auto Turn-on: The GTO-1001EZ has a signal sensing automatic turn-on circuit; it will turn on whenever an audio signal is present at the RCA inputs. The amplifier will automatically turn off approximately five minutes after the input signal ceases. If you prefer to use the radio's remote lead, the auto turn-on feature can be turned off.
Crossovers: Because this is a subwoofer amplifier, the low-pass crossover cannot be bypassed. The crossover point is continuously variable from 40 Hz to 280 Hz and the crossover's slope is 12 dB/octave.
Audio Input: If your radio has no line-level outputs, use the included adapters to convert the speaker wires to RCA and plug them into the amplifier's inputs. The input level switch has a Hi2 position, used to present a speaker load to factory radios equipped with a circuit that turns the radio off when an amp is connected.
Controls
Top:
- Crossover Frequency: rotary knob; continuously variable from 40 Hz to 280 Hz
- Input Gain: rotary knob (the gain LEDs are above the knob)
- Bass Boost: rotary knob; continuously variable from 0 to +12 dB; boost centered at 45 Hz
Right Side:
- Input Level: three position switch; Low, Hi1, or Hi2 (used only with factory radios having a circuit that turns the radio off when it sees no speaker load)
- Gain LEDs: on/off
Bottom:
- Auto Turn-on: on/off
Connections
Left Side:
- Power and Ground Terminals: set screw
terminals; accept up to 4 gauge bare wire
- Note: JBL recommends the power and ground cables be 6 gauge minimum. The recommended accessory list for the GTO-1001EZ includes wiring kits with 4 gauge wire and 150 amp fuses. If a different wiring kit having an in-line fuse smaller than 120 amps is used, a replacement fuse (at least 120 amps) must also be added.
- Remote Turn-on Terminal: set screw terminal; accepts up to 8 gauge bare wire
- Speaker terminal: one pair of set screw terminals; accepts up to 8 gauge bare wire
- Fuses: three ports for 40-amp ATO fuses (fuses are factory installed)
Right Side:
- Audio Input: left and right female RCA jacks; compatible with a speaker level signal using the included adapters
- Remote: RJ-25 jack (the wired remote is not yet available as of 2/17/12)
The JBL GTO-1001EZ replaces these items
Bazooka MGA11500H
- 810 watts RMS x 1 at 4 ohms
- variable low-pass filter (30-250 Hz, 12 dB/oct)
- variable bass boost (0-15 dB at 30-125 Hz)
JBL Grand Touring Series GTO1201.1 II
- 787 watts RMS x 1 at 4 ohms
- optional internal neon lighting (tubes not included)
- variable low-pass filter
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...
Really easy to install, and the disk that came with the amp made the set up quick and easy with a loud thump now
Devan from Newnan, Ga