About the Jensen DUBa11000D
Jensen + DUB
Jensen + DUB
Since 1925, Jensen has been a pioneer in home and car electronics, developing landmark products such as the first high-efficiency loudspeaker and the first aftermarket car speaker. Now Jensen has partnered with DUB® magazine, the leading publication in the urban automotive lifestyle market, to introduce DUB Edition speakers and amplifiers which feature DUB-designed cosmetics and co-designed components.
Boom for your zoom
The DUB Series DUBa11000D mono subwoofer amplifier will send up to 1000 watts RMS to your subs. The amp features variable low-pass and subsonic filters, along with an adjustable bass boost, that let you zoom in on the sound you want. This Class D amp uses a MOSFET power supply and high-current output transistors to deliver strong, reliable power, and it features full short-circuit, DC offset, and thermal protection, so the music won't stop until you want it to. And why would you want it to? You've got DUB on the case.
Confused about impedance? Check out our article on matching subs and amps.
Product highlights:
- mono subwoofer amplifier
- 475 watts RMS x 1 at 4 ohms (765 watts RMS at 2 ohms)
- 1,000 watts RMS x 1 at 1 ohm
- CEA-2006 compliant
- Class D amp technology
- high current Toshiba output transistors
- variable low-pass filter (40-300 Hz, 12 dB/octave)
- variable subsonic filter (16-40 Hz, 12 dB/octave)
- variable bass EQ: 0-12 dB at 45 Hz
- fuse rating: 35A x 3
- 4-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier
- dimensions: 13-3/16"W x 2"H x 8-1/8"D
- frequency response: 10-300 Hz
- weight: 6.5 lbs.
- warranty: 1 year
- MFR # Duba11000D
What's in the box:
Jensen DUBa11000D owner's manual
- Mono block Class D amplifier with three 35A ATO fuses installed
- 2 End caps
- 4 Machine screws for end caps (M3 x 6mm)
- Remote Input Level Control module
- 16.5' Remote Input Level Control cable (with 3.5mm plugs at both ends)
- 4 Self-tapping screws (Length=20mm)
- 2 Self-tapping screws for remote module (Length=10mm)
- Installation & Operation Manual
- Performance Certification card
Customer reviews for Jensen DUBa11000D
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Jensen DUBa11000D
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
475 x 1 | |
Peak Power Output (Watts x Channels) | 2000 x 1 | |
Power at 2 Ohms (Watts x Channels) | 765 x 1 | |
Power at 1 Ohm (Watts x Channels) | 1000 x 1 | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 1 | |
Minimum Impedance | 1 | |
Best Frequency Response | 10-300 Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 100 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 40-300 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 45 Hz | |
Fan Cooled | No | |
Fuse Rating | 105 | |
Speaker Level Inputs | --- | |
Preamp Outputs | 1 pair | |
Width (inches) | 13-3/16 | |
Height (inches) | 2 | |
Depth (inches) | 8-1/8 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Features
Overview: The Jensen DUB Edition amplifiers offer performance and value for your vehicle's sound system. With a MOSFET power supply and high-current Toshiba bi-polar output transistors, the DUB amps provide lots of power and control to give your music impressive punch and clarity. The Class D design reduces idle current and minimizes distortion.
Power Output: The DUBa11000D mono block amplifier delivers the following power output:
- CEA Specifications: RMS power output @ 1% THD+N, 10-300Hz, 14.4 VDC:
- 475 watts x 1 @ 4 ohms
- 765 watts x 1 @ 2 ohms
- 1000 watts x 1 @ 1 ohm
- RMS Power Output @ 2% THD+N, 1 kHz, 14.4 VDC:
- 500 watts x 1 @ 4 ohms
- 800 watts x 1 @ 2 ohms
- 1100 watts x 1 @ 1 ohms
Protection Circuitry: The amplifier features protection circuitry for thermal overload, DC-offset, and short circuits. The LED on the top of the amp glows yellow if a fault is detected.
Pass-thru RCAs: The DUBa11000D has a pair of RCA connectors that allow you to connect additional amplifiers without having to use a Y-adapter. The line output is unfiltered, providing the same signal as the RCA input.
End Caps: The DUB Edition amps include end caps to cover the wiring and controls for a clean installation. The end caps can be painted to match your vehicle, if desired. The end cap brackets can be removed if you wish to install the amp without the end caps.
Controls
Input Level: The DUBa11000D's rotary gain control let you match the amp's input sensitivity to the output of the source unit. The input sensitivity range of the amplifier is continuously variable between 400mV and 4V. A small screwdriver (not included) is required to set the gain.
Remote Input Level Control: The amp includes a Remote Input Level Control module with a 5-meter (16.5') interface cable. You can adjust the input level of the amplifier from the driver's seat or an alternate location. This allows you to tune the amount of bass you want for different types of music. The module can be mounted under or in the dash.
Low-pass Filter: The amp features a 12 dB/octave low-pass filter that is adjustable from 40 to 300 Hz.
Sub Sonic Filter: The Sub Sonic filter removes ultra-low frequencies that cannot be reproduced by most subwoofers. These frequencies do not become sound, but unnecessary oscillations which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to speakers. The filter's crossover point is variable from 10 to 40 Hz with a slope of 12 dB/octave.
Bass Boost: The DUBa11000D has a 0 to 12dB bass boost, centered at 45Hz.
Phase Switch: The amplifier has a Phase Switch that is selectable to 0° (normal polarity) and 180° (inverted polarity). You will need to perform a sound test with the Phase Switch at both positions, and set the switch to the position which produces the most dynamic bass.
Connections
Set-screw Terminals: The Jensen DUBa11000D uses set-screw terminals for the +12V power, ground, turn-on (remote) lead, and speaker outputs. The set-screws can be tightened/loosened with a Phillips-head screwdriver (not provided).
Power/Ground: The +12V Power and Ground terminals will accept up to 4 AWG wire. It is recommended that you use a 4 AWG power wire to the battery, with an in-line 100A fuse installed no more than 18" from the battery terminal. A 4 AWG ground wire (minimum) should be used, and attached to a metal area close to the amplifier.
Remote Turn-On: The Remote set-screw terminal will accept up to 8 AWG wire. Typically, an 18 AWG turn-on lead is included in an amplifier wiring kit.
Low-Level Input: The amplifier is equipped with a pair of RCA inputs for connecting a stereo RCA patch cable from the head unit to the amp. A stereo RCA line output is also provided for daisy-chaining another amplifier without requiring a Y-adapter.
Speaker Outputs: The amp features two positive and two negative set-screw terminals for connecting one or two speakers. For maximum power, it is recommended that you configure the speakers for a nominal 1-ohm load. The terminals will accept up to 8 AWG wire, however, it is recommended that you use a minimum of 12 AWG wire.
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...
All around great amp! Easy install too Haven't had any problems with it and takes a long time to heat up with use. I for sure recommend it if it fits what you're looking for.
Robbie from Asheville, North Carolina