About the Kenwood KAC-629S
Want to pump some serious power into your system without pumping too much cash out of your bank account? Then the powerful and affordable Kenwood KAC-629S is the amplifier for you!
Kenwood loaded this amplifier with components not usually found in this price range: MOSFET power supplies, extra-large capacitors, copper-shielded EE core transformers, and toroidal noise filters. Translation the KAC-629S will keep your music crisp and clean even at the highest sound levels.
Details:
- stereo or bridged mono output
- Tri-way capable (Tri-Way crossover required)
- 75 watts x 2 at 2 ohms
- 150 watts x 1 in bridged mode
- requires 10-gauge power and ground leads wiring and hardware not included with amplifier
- 80 Hz selectable low-pass crossover, 18 dB/octave
- 150 Hz selectable high-pass crossover, 12 dB/ octave
- speaker-level inputs
- 4-way protection circuitry
- signal-to-noise ratio 100 dB
- dimensions: 9-7/8"W x 2-1/4"H x 9-7/8"D
- 1-year warranty
What's in the box:
Kenwood KAC-629S owner's manual
- 2-Channel amplifier with one 25 amp fuse
- Rubber terminal cover
- 4 Self-tapping screws
- Instruction Manual (English)
- Instruction Manual (French/Spanish)
- Warranty Card
Customer reviews for Kenwood KAC-629S
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kenwood KAC-629S
Product Research
Features
Controls
Inputs and Outputs
Specifications
Ground Isolation Circuit: This circuit cancels noise from the input of the negative side of the RCA cable, preventing vehicle electrical noise from interfering with the music.
Quiet Turn-On: This feature allows the amplifier to power up over a period of several milliseconds instead of instantaneously, protecting your speakers from thumps and other sounds that could be damaging.
Internal Crossover: The internal crossover is a 12dB/octave crossover that can be set for 80Hz low-pass or 150Hz high-pass operation. The crossover may be turned off for full-range output.
Right Side Of Amplifier:
- Filter Switch: Allows you to select full range, 80Hz low-pass, or 150Hz high-pass crossover operation
- Stereo/L+R/Mono Switch: Allows you to choose stereo, mono or L+R amplifier operation. In L+R mode, the left and right signals are combined before being amplified.
- Input Sensitivity: This variable control allows you to adjust the input sensitivity of the amplifier from 0.2V-5V.
Right Side Of Amplifier:
- Line In: Gold-plated stereo RCA jacks
- Speaker Level Input: Screw terminals (each terminal is 0.25" wide)
Left Side Of Amplifier:
- Speakers: Gold-plated screw terminals (each terminal is 0.35" wide)
- BATT (power): Gold-plated screw terminal (terminal is 0.35" wide)
- GND (ground): Gold-plated screw terminal (terminal is 0.35" wide)
- P.CON (remote turn-on): Gold-plated screw terminal (terminal is 0.35" wide)
- Fuse: Inserted 25-amp fuse
Maximum Power Output:
- Bridged Into A 4-Ohm Load: 350 watts x 1
- Per Channel Into A 4-Ohm Load: 120 watts x 2
Rated Power Output:
- Bridged Into A 4-Ohm Load: 150 watts x 1
- Per Channel Into A 2-Ohm Load: 75 watts x 2
- Per Channel Into A 4-Ohm Load: 60 watts x 2
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Good amp powering my 12" sub never an issue
bryce from 61301 illinois