CEA-2006 Compliant: CEA-2006 is a system of testing and
measurement for mobile audio amplifiers. This voluntary standard advocates a
uniform method for measuring an amplifier's RMS power output and signal-to-noise
ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts
and the RMS power output is measured into a 4Ω load, with 1% or less Total
Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to
20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted
absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards
allow consumers to compare car amplifiers and receivers under the same conditions
(apples to apples). Using CEA-2006 criteria, the Kenwood KAC-6406 is rated at 40
watts RMS x 4 channels with an 80 dBA signal to noise ratio. The signal to noise
ratio at the rated power output (not CEA-2006 conditions) is 100 dB.
2-Ohm Stable: The amplifier can support a 2-ohm load in stereo;
the 2-ohm power output is 60 watts RMS x 4 channels.
Bridgeable: Each half of the four-channel amplifier can be
bridged into a 4-ohm mono load; the bridged output is 130 watts RMS x 2 channels.
If you prefer, just half the amp can be bridged for three-channel operation (40
watts RMS x 2 channels + 130 watts RMS x 1 channel).
Cast Aluminum Heat Sink: The KAC-6406 utilizes a cast aluminum
heat sink design to ensure the amplifier stays cool.
Protection circuitry: The amplifier features protection
circuits that will turn the amp off in case of the following events:
- speaker wire short-circuits
- speaker output contacts ground
- unit malfunctions and DC is sent
to speaker output
- the amp overheats
Power Indicator: When the amplifier is turned on the Power
indicator (on top of the amp) lights up. This indicator turns off with the
amplifier, and will turn off if the amplifier goes into protect mode.
Auto Turn-on: When using a speaker level input, the amp will
turn on automatically when it senses the input signal.
Gain: To accommodate the varying range of signal levels from
today's factory and aftermarket radios, the KAC-6406 features an adjustable gain
control; 0.2-5.0 volts line level (RCA) and 4.0-12.0 volts speaker level.
Crossover: The four-channel amp is separated into two
halves, labeled A and B. The A and B sections have independent crossovers:
- A-Channels: high pass with a fixed 80 Hz crossover
point; 12 dB/octave slope; can be turned on or off
- B-Channels: low-pass with a continuously variable
(50-200 Hz) crossover point; 24 dB/octave slope; can be turned on or off
Power Connections: The power and ground connections are
0.5" wide screw terminals. The remote turn-on screw terminal is 0.35"
wide. A Phillips-head or flat blade screw driver (not supplied) is required to
tighten/loosen the terminals. Spade connectors are recommended. Minimum 10 gauge
wire is required for power and ground.
Speaker Outputs: The four pair of speaker outputs are 0.35"
wide screw terminals. A Phillips-head or flat blade screw driver (not supplied)
is required to tighten/loosen the terminals. Spade connectors are also recommended
for the speaker wires.
Line Level Input: The line input is
two pair of stereo RCA
jacks (A-channels and B-channels).
Speaker Level Input: A wiring harness is included for the
speaker level input.
Fuse: The amplifier uses a 30-amp ATO blade-type fuse.
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to
find elsewhere. That's because we have our own in-house Product Research
team. They verify what’s in the box, check the owner's manual, and record
dimensions, features and specs. We stay on top of new products and technologies
to help people make informed choices.