About the Kenwood KAC-8405
Kenwood Performance Series car amplifiers offer long-term reliability and superior sound quality in a compact, no-nonsense package. The KAC-8405 4-channel amp delivers 60 watts RMS to each of your front and rear speakers, or you can drive a couple of subs with 180 watts RMS each in 2-channel mode. A rugged cast-aluminum heatsink combines with two cooling fans to keep this amp running at optimal temperatures, even when you're pushing your system hard.
Built-in high- and low-pass filters adjust the output so you'll get the best sound possible from your system. You can dial in up to 18 dB of bass boost to fatten up the sound.
An aluminum cover plate covers and protects the amp's controls and connections, giving your installation a professional look. Speaker-level inputs and signal sensing turn-on allow these amps to hook up to factory radios without preamp outputs.
Product highlights:
- 4-channel car amplifier
- 60 watts RMS x 4 at 4 ohms (90 watts x 4 at 2 ohms)
- 180 watts RMS x 2 bridged output at 4 ohms (4 ohm stable in bridged mode)
- 2-, 3-, and 4-channel operation
- CEA-2006 compliant
- variable high- and low-pass filters (50-200 Hz, 12 dB per octave)
- variable bass boost (0-18 dB at 40 Hz)
- dual cooling fans
- MOSFET power supply
- speaker-level inputs with signal sensing turn-on
- preamp inputs
- fuse rating: 30A x 2
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 11"W x 2-3/8"H x 9-1/2"D
- warranty: 1 year
- MFR # KAC-8405
What's in the box:
Kenwood KAC-8405 owner's manual
- 4-Channel amplifier (with two 30A ATO fuses inserted in chassis)
- 8" Speaker-level input harness
- 4 Self-tapping screws (4mm diameter x 16mm)
- Allen wrench
- Instruction Manual (Eng/Fre/Spa)
- Warranty card
Customer reviews for Kenwood KAC-8405
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kenwood KAC-8405
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
60 x 4 | |
Peak Power Output (Watts x Channels) | 180 x 4 | |
Power at 2 Ohms (Watts x Channels) | 90 x 4 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 180 x 2 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 5-50k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 95 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | AB | |
Low-Pass Crossover Frequency | 50-200 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | 50-200 Hz | |
High-Pass Slope (dB/octave) | 12 dB/oct | |
Bass Boost | 0-18 dB | |
Bass Boost Frequency | 40 Hz | |
Fan Cooled | Yes | |
Fuse Rating | 60 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 11 | |
Height (inches) | 2-3/8 | |
Depth (inches) | 9-1/2 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Controls
Connections
Features
MOSFET Switching Power Supply: The amplifier utilizes a MOSFET switching power supply providing thermal stability and efficient switching speeds guaranteeing performance and dependability.
CEA 2006 Compliant: The KAC-8405's power ratings are measured according to the strict standards dictated by the Consumer Electronics Association (CEA). These standards allow you to accurately compare the rated power output of all CEA 2006-compliant amplifiers, even if they come from different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging.
Amplifier Rating: The Kenwood KAC-8405 Four-Channel amplifier is bridgeable (4-ohm), as well as 2-ohm stable in stereo.
- Four-Channel (CEA 2006 Compliant): 60 watts x 4 channel RMS @ 4 ohms (20 Hz-20 kHz, 1% THD)
- Four-Channel (2-ohm): 90 watts x 4 channel RMS (1 kHz, 0.08% THD)
- Bridged (4-ohm): 180 watts x 2 channel RMS (1 kHz, 0.08% THD)
- Peak Power: 180 watts x 4 channel (720 watts total max power)
Cast Aluminum Heat Sink: The Kenwood KAC8405 utilizes a cast aluminum heat sink design to ensure that the amplifier stays at its optimal temperature.
Fan Cooled: There are two fans and two vents located on the back side of the amplifier to help dissipate heat and ensure cool, reliable operation. Make sure not to block these vents or fans when you install the amplifier.
Protection circuitry: The amplifier features protection circuits that will turn the amp off in case of the following events:
- Speaker output contacts ground
- Speaker wire short-circuits
- Unit malfunctions and DC is sent to speaker output
Aluminum Cover Plate: The amplifier's controls and connections are hidden under a removable extruded aluminum cover plate. The cover plate provides a professional looking installing while helping to protect the amplifier's connections and control settings. The cover is held in place by two hex head screws. An allen-wrench is supplied to remove the cover.
Blue/Red Illumination: The Kenwood Four-Channel amplifier features a blue and red LED illumination when the amplifier is turned on. When the power is turned on to the amplifier, the Power indicator will light up red. This indicator will turn off with the amplifier and will turn off if the amplifier goes into protect mode. The amplifier also features a Blue LED lamp on the top of the amplifier which illuminates when the amplifier is on.
Signal-sensing Turn-On Circuitry: When the speaker-level input is used, it is not necessary to connect the power control wire (turn-on lead). The amplifier senses the signal from the speaker-level input and turns the amplifier power on automatically. Shortly after no signal is detected, the amplifier will automatically shut itself off.
Controls
Stereo/Mono Operation: You can independently switch Amplifier's front and rear channels from Stereo to Mono operation. When switched to Mono, the signal from the left channel inputs are only used.
Gain: To accommodate the varying range of signal levels coming from today's factory and aftermarket radios, the Kenwood KAC-8405 features an adjustable, independent gain control (0.2-5.0V) for the front and rear channels. This means that no matter what kind of radio is connected to this amplifier, the appropriate gain control adjustment can be made to ensure loud, clear, distortion-free music.
Crossovers: The KAC-8404 has built-in high pass and low pass crossovers. The high pass crossover's slope is 12 dB/octave and is continuously variable from 50Hz to 200Hz and can be controlled independently for the front and rear channels. The low pass crossover's slope is also 12 dB/octave and continuously variable from 50Hz to 200Hz and can be controlled independently for the front and rear channels. The amplifier can also be operated at full-range simultaneously for both the front and rear channels.
Bass Boost: A fixed bass boost of 18dB at 40Hz can be engaged for the rear-channels only. There is no bass boost for the front channels.
Connections
Power Connections: The power, ground, and remote turn-on connections are 0.3125" wide screw terminals that will accommodate up to 8-gauge wire. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended for the power, ground, and remote wires.
Speaker Outputs: The Kenwood KAC-8405 is equipped with four pair of speaker terminals. All eight speaker terminals are 0.3125" wide screw terminals and will accommodate up to 8-gauge wire. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended for the speaker wires.
Note: The speaker output terminals can be used in 4-channel mode or bridged to 2-channels.
Line Level Input: The four-channel amplifier is equipped with two pair of gold-plated RCA line level inputs.
Speaker Level Input: The KAC-8405 comes with a four channel speaker level input harness. Once you splice the speaker wires from the receiver to the harness, you have plug-in convenience to the amplifier. This feature makes it easier to add an amplifier to a factory radio or to a receiver with no preamp outputs. The maximum power output from the source receiver can be no more than 40 watts.
Fuses: The KAC-8405 is equipped with two 30 amp ATC blade fuses.
The Kenwood KAC-8405 replaces these items
Polk Audio PA200.4
45 watts RMS x 4
- 100 watts RMS x 2 at 4 ohms (4-ohm stable in bridged mode)
- selectable high- and low-pass filters
- selectable bass boost
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Have this amp running my highs and mids(Polk Audio) does a awesome job. Barely have them gains turned up. Nice that is has built in fans. Reasonable price
rocuno from Florence, Az