About the Kenwood P-W100B 150-Watt Bass Package
Solid package
Solid package
This Kenwood bass package includes the KAC-5206 amplifier and a ported enclosure with a 10" sub. The sub's injection-molded polypropylene cone handles your bass frequencies with ease, while its ported enclosure maximizes your low-frequency punch.
Small enclosure
The enclosure is made to fit into tight spaces, with a depth of only 7-1/4 inches. It'll fit behind truck seats and in tight trunks, making use of the empty space for great bass in a small package.
Powerful amplification
The KAC-5206 Class AB amplifier delivers 150 watts RMS in mono mode to the enclosure, while its built-in low-pass filter sends only the lows to the 10" sub. You'll be able to hear and feel the low-frequency notes your car's full-range speakers can't play.
Product highlights:
- package includes Kenwood KAC-5206 2-channel amplifier and ported enclosure with 10" subwoofer
KAC-5206 2-channel Amplifier:
- 150 watts RMS x 1 bridged at 4 ohms (60 watts RMS x 2 at 4 ohms)
- fixed low-pass filter (80 Hz at 18 dB per octave)
- preamp and speaker-level inputs
- requires 10-gauge power and ground leads — wiring and hardware not included with amplifier
- dimensions: 8-7/8"W x 2-3/16"H x 7-1/16"D
- warranty: 1 year
Subwoofer Enclosure:
- one 10" 4-ohm woofer
- ported enclosure
- power handling: 175 watts RMS (700 watts peak)
- frequency response: 45-500 Hz
- sensitivity: 86 dB
- enclosure dimensions: 21-11/16"W x 14-1/2"H x 7-5/16"D
- warranty: 1 year
- MFR # P-W100B
What's in the box:
Kenwood P-W100B 150-Watt Bass Package owner's manual
- Enclosure loaded with one 10" Subwoofer
- 2-Channel KAC-5206 amplifier
- 25 amp ATO fuse (installed)
- 7" Speaker-level input harness
- 2 Subwoofer mounting brackets
- Eight 1" Screws
- Four 5/8" Screws
- System wiring instructions
- Amplifier instruction manual (English/ French/ Spanish)
- Warranty information
Customer reviews for Kenwood P-W100B 150-Watt Bass Package
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kenwood P-W100B 150-Watt Bass Package
Product Research
Features
Subwoofer Features:
- Terminals: spring post terminals (one pair); mounted on the right side of the enclosure; will accept pin connectors, single or dual banana plugs (3/4" width), or bare wire up to 10 gauge
- Port: slot port on the right side of the enclosure, at the top
- Dimensions:
- Width: 21-7/8"
- Height: 14-1/2"
- Depth (at base): 7-3/8" (8-1/8" including the subwoofer flange)
- Depth (at top): 4-1/8"
Amplifier Features:
- Auto Turn-on: when using a speaker level input, the amp will turn on automatically when it senses the input signal
- Crossover: 80Hz, -18 dB/oct low-pass crossover; can be turned On/Off (should be turned on to power the subwoofer)
- Bridgeable: two-channel amplifier is bridged to the 4Ω mono subwoofer load; the bridged output is 150 watts x 1 channel RMS
- Power Connections: power, ground, and remote turn-on connections are 0.35" wide screw terminals; Phillips-head or flat blade screw driver (not supplied) required to tighten/loosen the terminals; spade connectors recommended; minimum 10 gauge wire required for power and ground
- Speaker Outputs: two pair of speaker outputs; 0.35" wide screw terminals; Phillips-head or flat blade screw driver (not supplied) required to tighten/loosen the terminals; spade connectors also recommended for the speaker wires
- Line Level Input: one pair of stereo RCA jacks
- Speaker Level Input: wiring harness is included
- Gain: continuously variable gain control; 0.2-5.0 volts line level (RCA); 4.0-12.0 volts speaker level
- Protection circuitry: The amplifier features protection
circuits that will turn the amp off in case of the following:
- speaker wire short-circuits
- speaker output contacts ground
- unit malfunctions and DC is sent to speaker output
- the amp overheats
- Cast Aluminum Heat Sink: cast aluminum heat sink designed to ensure the amplifier stays cool
- Fuse: one 25-amp ATO blade-type fuse
- Dimensions:
- Width: 9-1/8"
- Height: 2-1/8"
- Depth: 7-1/8"
- CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). Using CEA-2006 criteria, the Kenwood KAC-5206 is rated at 60 watts RMS x 2 channels with an 80 dBA signal to noise ratio. The signal to noise ratio at the rated power output (not CEA-2006 conditions) is 95 dB.
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...
Outstanding price and sound quality. This was perfect for my 2004 Nissan Xterra, it added the sound I wanted. This Kenwood Sub and Amp would be perfect for anyone.
Johnathan from Shawnee, KS