1-888-955-6000
crutchfield.com
Crutchfield

JL Audio Slash 1200/1v3

Mono subwoofer amplifier — 1,200 watts RMS x 1

Save 50% on a select amp wiring kit with any $249+ car amplifier with any $249+ car amplifier
Zoom
  • JL Audio Slash 1200/1v3

    Front

  • JL Audio Slash 1200/1v3

  • JL Audio Slash 1200/1v3

  • JL Audio Slash 1200/1v3

Crutchfield OMC logo
We don't check this item for fit or compatibility.
 

Our take on the JL Audio Slash 1200/1v3

by Buck Pomerantz
JL Audio

My system has plenty of power. Who needs an amp?

You might think you don't need an amp because you have a 400-watt system in your car, or because your new stereo puts out 50 watts a channel. But those are peak wattage ratings, which may boil down to 15 or 20 watts per channel, using the more realistic RMS rating. An amp sends your speakers the power they need to deliver your music with clarity and impact, whether you're using factory speakers or high-performance components. And low-frequency reproduction requires lots of power, so an amp is an absolute must if you're adding a sub to your system.

Pure power for your subs

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy powerful, moving bass in your car. Its patented Class-D amp circuitry delivers exceptional, natural sound with extremely low distortion, while a parametric EQ bass boost give you precise control over your bass. You can add the RBC-1 wired remote (not included) to dial in the right amount of thump from the front seat.

Consistent power for performance you can count on

This Slash v3 amplifier isn't just powerful, it's smart. As your car system's voltage fluctuates while you drive, the Regulated, Intelligent Power Supply™ system maintains steady, consistent power at any impedance between 1.5 and 4 ohms and at any voltage between 11 and 14.4 volts. You'll get all the power, all the time, even with a wide range of speaker combinations.

Minimize external noise

The 1200/1v3 uses "differential-balanced inputs" to isolate the signal's ground from the chassis ground, reducing noise and making this Slash v3 amplifier compatible with almost any system, including most factory radios. You can adjust the variable infra-sonic- and low-pass filters to maximize the performance of your subwoofers.

JL Audio 1200/1v3

Slash 1200/1v3 control and connection panel

See more info on this item

Highlights:

  • mono subwoofer amplifier
  • 1,200 watts RMS x 1 at 1.5 to 4 ohms
  • Regulated, Intelligent Power Supply system
  • differential-balanced inputs
  • variable low-pass filter (40-200 Hz, 12 or 24 dB/octave)
  • parametric EQ bass boost (0-15 dB at 20-80 Hz)
  • variable infrasonic filter (15-60 Hz, 24 dB/octave)
  • optional wired remote bass boost
  • Class-D amplifier design
  • MOSFET power and output stages
  • preamp and speaker-level inputs (speaker-level input requires an optional adapter)
  • preamp outputs
  • 4-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended
  • 19-3/4"W x 2-3/8"H x 9-7/8"D
  • warranty: 2 years
  • Our 60-day money-back guarantee

Hands-on research from the Crutchfield Labs (what are the Labs?)

Features and Specs
Performance
RMS Power Output (Watts x Channels)
Loading...
1200 x 1
Peak Power Output (Watts x Channels)
Loading...
N/A
Power at 2 Ohms (Watts x Channels)
Loading...
1200 x 1
Bridged Power (Watts x Channels)
Loading...
N/A
Minimum Impedance Bridged
Loading...
N/A
Minimum Impedance Unbridged
Loading...
1.5
Best Frequency Response
Loading...
5-250 Hz
THD at Rated RMS Power
Loading...
0.05%
Signal to Noise Ratio
Loading...
95 dB
Input Voltage
Loading...
12.5v
Features
Amplifier Class
Loading...
D
Low-Pass Crossover Frequency
Loading...
40-200 Hz
Low-Pass Slope (dB/octave)
Loading...
12 or 24 dB/oct
High-Pass Crossover Frequency
Loading...
N/A
High-Pass Slope (dB/octave)
Loading...
N/A
Bass Boost
Loading...
0-15 dB
Bass Boost Frequency
Loading...
20-80 Hz
Fan Cooled
Loading...
No
Fuse Rating
Loading...
100
Speaker Level Inputs
Loading...
RCA
Preamp Outputs
Loading...
1 pair
Width (inches)
Loading...
19-3/4
Height (inches)
Loading...
2-3/8
Depth (inches)
Loading...
9-7/8
Parts Warranty
Loading...
2 Years
Labor Warranty
Loading...
2 Years
Product Research
What's in the box?

Download owner's manual

  • Monoblock subwoofer amplifier
  • 2.5mm Allen wrench
  • Owner's manual

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Features
Controls
Connections

Features

Mono Subwoofer Amplifier: The JL Audio 1200/1v3 is a class D monoblock subwoofer amplifier. With its regulated power supply, the rated output is 1,200 Watts RMS x 1-channel into a load of 1.5Ω to 4Ω, with an input voltage of 11V to 14.5V. The signal to noise ratio is >95 dB and a total harmonic distortion is <0.05%, both measured at rated power (1,200 watts RMS). The amplifier's frequency response is 5-250Hz. (It is not designed for driving full range speakers.)

R.I.P.S. (Regulated Intelligent Power Supply): The JL Audio R.I.P.S. system ensures consistent power delivery over a wide range of battery voltages and load impedances, providing the rated power output at any impedance from 1.5Ω to 4Ω and at any vehicle voltage from 11V to 14.5V.

  • Regulated Power Supply: The power supply adjusts to maintain the amplifier's rated power output and low distortion operation over a wide range of vehicle voltages (11V-14.5V), so the amplifier's output remains stable in real-world car audio situations.
  • Intelligent Power Supply: An Intelligent circuit monitors output current to optimize the amplifier's output power over a wide range of load impedances (1.5Ω to 4Ω). The R.I.P.S. System detects the actual load impedance, rather than relying on often inaccurate assumptions based on a speaker's rated impedance, and adjusts output rail voltages to deliver consistent output.

RealSink Heat Management: This Slash v3 amplifier features a real cast-alloy heat sink with vertically-oriented fins, very effective at dissipating heat from the amplifier via convection and radiation. This design is achieved through extensive finite-element analysis, resulting in an amplifier that keeps cool under the most demanding conditions. As an added cosmetic benefit, the cast-aluminum end-caps replicate half of a heat sink fin so that when two or more amplifiers are mounted end-to-end, you get a seamless custom look.

Advanced Rollback Protection: If a Slash v3 amplifier should ever reach an unsafe temperature, the Advanced Rollback Protection circuit reduces power until the amplifier cools down, without turning the music off completely.

Class D Circuitry: JL Audio's Patented Class D output circuit utilizes a discrete control section and a unique feedback loop design, resulting in a damping factor greater than 500 at 4Ω (>250 at 2Ω), higher than most other Class D and Class A/B designs. The benefit is tight, clean bass reproduction with the efficiency advantage of Class D.

Differential-Balance Inputs: The 1200/1v3 features differential-balanced input architecture to reject noise and ensure compatibility with a wide variety of source units, including many OEM systems. Without using a line output converter, you can connect most OEM or aftermarket source units to the amplifier without creating any noise or compatibility issues.

Note: You will need a speaker wire to RCA adaptor (item number 136XDCLR2S, sold separately) when using a speaker-level input.

Preamp Outputs: The preamp outputs make connecting multiple amplifiers simple. The 1200/1v3 features an independent crossover for the preamp output with frequency (40-200 Hz), mode (Full Range, LP, or HP) and slope (12 or 24 dB) adjustments.

Protection Circuitry With Status Indicator Lights: There are four status indicator lights on the top of the amplifier:

  • Power (Green): green LED indicates the amplifier is turned on and operating normally
  • Thermal (Red): red LED indicates the amplifier has exceeded its safe operating temperature; the power output is reduced until the heat sink temperature drops back to a safe level
  • Low Ω (Amber): amber LED indicates the impedance of the connected speaker(s) is lower than the optimum impedance range for the amplifier and the power output is reduced; the amber LED can also indicate a short in the speaker wire
  • Low V (Blue): blue LED indicates a drop in supply voltage below 8 volts; the LED will remain lit longer than the duration of the voltage drop to alert you to the problem; in this situation the amplifier will also shutdown (and the green LED turns off); once the voltage rises above 9 volts, the amplifier will turn itself back on

Infrasonic Filter: Ultra-low frequencies that cannot be reproduced by a subwoofer do not become sound, but unnecessary oscillations which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to speakers. Using the infrasonic filter, variable from 15 Hz to 60Hz, removes the signal below the setting to improve the performance of the speakers by eliminating harmful distortion. The infrasonic filter can be turned off.

Controls

Simplified Gain Setting: The amplifier's R.I.P.S. feature allows easy gain setup. Because the amplifier always delivers the same output power within its operational range of load impedance and power supply voltage, the maximum, unclipped output is predictable. This makes setting input gain very simple; you'll need a Digital AC Voltmeter (sold separately) and a CD with a sine-wave bass test tone recorded at 0 dB reference level (item number 503CD104, sold separately). In addition to the continuously variable rotary gain control, the Input Voltage switch adjusts the gain range, set to Low (200mV-2V) or High (800mV-8V).

Low Pass Crossover: The built-in crossover allows you to adjust the frequency and filter slope of the amplifier's powered output:

  • Mode/Slope Switch:
    • Off: crossover is bypassed, useful when using an external crossover; in this position the Advanced Bass Control is defeated
    • 12 dB: filter slope is 12 dB/octave, often used when the subwoofer is in the trunk of a sedan
    • 24 dB: filter slope is 24 dB/octave
  • Frequency: crossover frequency variable from 40 Hz to 200 Hz; the detented potentiometer allows accurate adjustment

Preamp Output Crossover: An independent crossover address what frequencies the preamp outputs will pass:

  • Output Mode:
    • Full Range: the preamp output is the same as the amplifier's input; the signal is not affected by the Advanced Bass Control
    • Amp Filter: the preamp output signal is the same as the amplifier's powered output, governed by the Low Pass Crossover and Advanced Bass Control
    • Out Filter: the independent crossover controls affect the preamp output:
      • Filter Slope: 12 dB/octave or 24 dB/octave
      • Filter Mode: Low Pass or High Pass
      • Filter Frequency: crossover frequency variable from 40 Hz to 200 Hz; the detented potentiometer allows accurate adjustment

Advanced Bass Controls: The bass control functions on the amplifier include:

  • Variable Bass Boost: The amplifier's variable bass boost features a single band parametric equalizer with variable Q (0.5 - 4.3), center frequency (20 Hz to 80 Hz), and boost (0 to +15dB).
  • Infrasonic Filter: The 24dB/octave infrasonic filter has a variable crossover point (15 Hz to 60 Hz). The infrasonic filter can be turned off.
  • Remote Bass Port: The amplifier is equipped with a connection for an optional wired Remote Bass Control (item number 136RBC1, sold separately), allowing boost control from the front of your vehicle.

Output Polarity: Depending on the distance between the mid-bass speakers and the subwoofer in your system, it might be preferable to reverse the polarity of the subwoofer to produce a better transition between the two. The Output Polarity switch allows you to quickly reverse the subwoofer's polarity (0°/180°).

Connections

Power and Ground: The amplifier's set-screw Power and Ground connections accept up to 4-gauge wire (4-gauge minimum is recommended).

Note: The Amplifier is not equipped with a fuse. An external 100-amp fuse (not included) must be installed on the power wire. If the system has only this amp and a wiring kit is used that includes a fuse with a value other than 100-amps, the original should be replaced with a 100-amp fuse.

Speaker Output Terminals: The two pair of set-screw speaker terminals accept 12-gauge to 8-gauge wire. The terminals are internally shorted together, making it easy to connect two subwoofers.

Remote Turn-On: The set-screw turn-on lead terminal will accept 12-gauge to 8-gauge wire.

Note: If your headunit does not have a dedicated remote turn-on output, the amplifier's turn-on lead can be connected to a switched +12V volt circuit.

Preamp Inputs: The amplifier features one set of differential-balanced RCA inputs. The amplifier's input level can be set to Low (200mV-2V RMS) when connecting the amplifier to a low-level preamp signal or set to High (800mV-8V RMS) when connecting the amplifier to a higher voltage preamp or speaker-level signal.

Preamp Outputs: The amplifier also features one set of preamp outputs so you can send audio to another amplifier in your system. The preamp output can be full range, or the built-in crossover can be applied.

Note: All inputs, outputs and controls are located on the front side of the amplifier to make installation simple and neat.
 
Review this product
Great Gear Giveaway rewards card

Submit a review and then enter to win a $500 rewards card

JL Audio Slash 1200/1v3 Reviews

Average Customer Review:

1 people say:

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left
Filter by rating:
5 out of 5

AMAZING POWER!!!

Written By Matt, Albuquerque on Thursday, April 11, 2013
 
I have this amp with two new JL W6v3 12" subs and I haven't even turned the sensitivity up due to the fact that I'm breaking in the subs, and my lights are dimming down to almost off and I blew the distribution block 100amp fuse. I'm definitely gonna have to get a better battery and new alternator. Just an amazing amount of power.
Pros:
Everything!
Cons:
Nothing! Besides your probably gonna have to get an alternator and deep cycle battery.
5 out of 7 people found this helpful
Was this review helpful?    Yes | No
 

Add accessories for the JL Audio Slash 1200/1v3

You'll need an amp wiring kit to install your new amplifier, as wiring is not included. See all categories & accessories

Rockford Fosgate RFK4X Complete 4-gauge amplifier wiring kit
Includes patch cable and speaker wire
12 people say
Your Price: $159.99
Add to Cart
EFX PA4BX Wiring Kit 4-gauge amplifier wiring kit — includes 2-channel patch cable
Your Price: $79.99
Add to Cart
Rockford Fosgate RFK4 4-gauge amplifier power wiring kit
9 people say
Your Price: $114.99
Add to Cart
T-Spec 4RAK Installation Kit 4-gauge amplifier wiring kit — includes 2-channel patch cable and speaker wire
6 people say
Your Price: $99.99
Add to Cart
T-Spec 4PK Installation Kit 4-gauge amplifier wiring kit — includes speaker wire
3 people say
Your Price: $89.99
Add to Cart
T-Spec 12-gauge Speaker Wire Black/white jacket — priced per foot
26 people say
Your Price: $1.99
Add to Cart
T-Spec 16-gauge Speaker Wire Black/white jacket — priced per foot
11 people say
Your Price: $0.69
Add to Cart
Stinger PRO Series 16-gauge Speaker Wire Black jacket — priced per foot
45 people say
Your Price: $0.39
Add to Cart
T-Spec 2-Channel RCA Patch Cables Available in 7 different lengths (17-foot)
23 people say
Your Price: $19.99
Add to Cart
JL Audio XD-CLRAIC2-SW 2-channel speaker output converter (bare speaker wires to male RCAs)
12 people say
Your Price: $9.99
Add to Cart
51 people say
Your Price: $9.99
Add to Cart
Rockford Fosgate RFFM100 MAXI Fuse Pair of 100-amp platinum-plated wafer fuses
2 people say
Your Price: $4.99
Add to Cart
T-SPEC V8 Mini-ANL Fuses Pair of nickel-plated mini-ANL fuses (100-amp)
7 people say
Your Price: $3.99
Add to Cart
JL Audio RBC-1 Remote bass control for JL Audio amps
19 people say
Your Price: $34.99
Add to Cart
T-Spec Capacitor 1.5-farad capacitor with red LCD meter
9 people say
Your Price: $79.99
Add to Cart
T-Spec Capacitor 3.0-Farad capacitor with red LCD meter
7 people say
Your Price: $99.99
Add to Cart
S&G Wire Cutter/Stripper Tool Cuts and strips 12- to 22-gauge wire
14 people say
Your Price: $19.99
Add to Cart
Pro.Fit Wire Worm Installation tool helps route wiring through tight spaces
27 people say
Your Price: $12.99
Add to Cart
Metra Crimp Tool and Connectors Package contains crimp tool and over 150 pieces
15 people say
Your Price: $19.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
51 people say
Your Price: $24.99
Add to Cart
S&G Tool Aid 87650 Door Trim and Panel Removal Tool
65 people say
Your Price: $9.99
Add to Cart
Skewdriver Pro SPK4042 Ratcheting straight and offset screwdriver set with 40 bits (Skewdriver Pro with ratchet handle, pictured)
7 people say
Your Price: $49.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
2 people say
Your Price: $29.99
Add to Cart
DEI Heat Shrink Tubing Black 4-foot length (Assortment)
6 people say
Your Price: $24.99
Add to Cart
InstallCard: Amp or Equalizer Prepaid professional amplifier or EQ installation
17 people say
Your Price: $79.99
Add to Cart
Kicker 09PKD1 1/0-gauge multi-amp wiring kit
2 people say
Your Price: $399.99
Add to Cart
Autosound 2000 Disc Four Amplifier Optimizer Test CD
8 people say
Your Price: $9.99
Add to Cart
Autosound 2000 Disc One Low Frequency Test CD (Disc One)
1 person says
Your Price: $19.99
Add to Cart
Your Price: $69.95

After $10.00 Price Break

Add to Cart
Autosound 2000 Disc Five System Demonstration — Test CD
Your Price: $9.99
Add to Cart
Autosound 2000 Disc Two Image/Placement Test CD
Your Price: $19.99
Add to Cart
Autosound 2000 Disc Three System/Environmental Test CD
Your Price: $19.99
Add to Cart

Why choose SquareTrade?

The #1-Rated Protection Plan

Thousands of people have reviewed SquareTrade Protection Plans — and made us #1.

5-Day Service Guarantee & Free Shipping

We'll repair or replace your item in five business days or less after we've received it, or your plan is free. And, as always, we pay for all shipping.

Protection from Normal, Everyday Use

Repairing your average mechanical or electrical failure can cost as much as buying a new device. With SquareTrade, you're covered — including parts and labor.

3 Year Protection Plan
3 Year Protection Plan
Your Price: $144.99
Add to Cart
4 Year Protection Plan
4 Year Protection Plan
Your Price: $187.99
Add to Cart

For a more in-depth review and enhanced detailed information on the JL Audio Slash 1200/1v3, please visit the Crutchfield website product page (/ISEO-rccbcspd/p_13612001V3/JL-Audio-Slash-1200-1v3.html ).