JL Audio Slash 300/4v3

4-channel car amplifier — 75 watts RMS x 4

Item #: 1363004V3

In Stock

4 Reviews | Ask Questions

Your price: $599.99 Earn up to 600 Rewards points

Add to Cart Free Shipping Lifetime Tech Support

+ Add to wishlist + Email me alerts for this product

View all associated offers

1.888.955.6000

Email

Chat

We don't check this item for fit or compatibility.

Pure power for your system

JL Audio's 300/4v3 4-channel amplifier puts out 75 watts RMS per channel to your speakers, so you'll enjoy powerful, moving music in you car. You can also configure this amp to 2-channel mode and run two subwoofers with 150 watts RMS each. JL Audio's patented Class-AB amp circuitry delivers exceptional, natural sound with extremely low distortion. The cast aluminum heatsink dissipates heat quickly, so the amp will run reliably for a long, long time.

Consistent power for performance you can count on

This Slash v3 amplifier isn't just powerful, it's smart. As your car system's voltage fluctuates while you drive, the Regulated, Intelligent Power Supply™ system maintains steady, consistent power at any impedance between 1.5 and 4 ohms and at any voltage between 11 and 14.4 volts. You'll get all the power, all the time, even with a wide range of speaker combinations.

Minimize external noise

The 300/4v3 uses "differential-balanced inputs" to isolate the signal's ground from the chassis ground, reducing noise and making this Slash v3 amplifier compatible with almost any system, including most factory radios. Variable high- and low-pass filters give you precise level of control needed to maximize the performance of your speakers or subwoofers.

Product Highlights:

  • 4-channel car amplifier
  • 75 watts RMS x 4 at 1.5 to 4 ohms
  • 150 watts RMS x 2 at 3 to 8 ohms
  • Regulated, Intelligent Power Supply system
  • differential-balanced inputs
  • variable high- and low-pass filters (50-5000 Hz, 12 or 24 dB/octave)
  • Absolute Symmetry™ Class-AB amplifier design
  • MOSFET power and output stages
  • preamp and speaker-level inputs (speaker-level input requires two optional adapter packs)
  • 4-gauge power and ground leads and a 40-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 40-amp in-line fuse between the distribution block and the amplifier is recommended
  • 13-7/16"W x 2-1/4"H x 10"D
  • warranty: 2 years
  • Our 60-day money-back guarantee

My system has plenty of power. Who needs an amp?

You might think you don't need an amp because you have a 400-watt system in your car, or because your new stereo puts out 50 watts a channel. But those are peak wattage ratings, which may boil down to 15 or 20 watts per channel, using the more realistic RMS rating. An amp sends your speakers the power they need to deliver your music with clarity and impact, whether you're using factory speakers or high-performance components. And low-frequency reproduction requires lots of power, so an amp is an absolute must if you're adding a sub to your system.

Hands-on research

What's in the box?

Download owner's manual

  • Four channel amplifier
  • 2.5mm Allen wrench
  • Owner's manual

Product Research

Features
Controls
Connections

Features

Four-Channel Full-Range Amplifier: The JL Audio 300/4v3 is a class A/B four-channel, full-range amplifier, rated at 75 watts RMS x 4-channels into a 1.5Ω to 4Ω load, measured from 20 Hz to 20kHz with a power supply voltage of 11 to 14.5 Volts. The signal-to-noise-ratio is 108.5 dB and total harmonic distortion is 0.03%, both at rated power from 20 Hz to 20kHz. The amplifier can also be bridged to output 150 watts RMS x 2-channels into 3Ω to 8Ω loads.

R.I.P.S. (Regulated Intelligent Power Supply): The JL Audio R.I.P.S. system ensures consistent power delivery over a wide range of battery voltages and load impedances, providing the rated power output at any impedance from 1.5Ω to 4Ω and at any vehicle voltage from 11V to 14.5V.

  • Regulated Power Supply: The power supply adjusts to maintain the amplifier's rated power output and low distortion operation over a wide range of vehicle voltages (11V-14.5V), so the amplifier's output remains stable in real-world car audio situations.
  • Intelligent Power Supply: An intelligent circuit monitors output current to optimize the amplifier's output power over a wide range of load impedances (1.5Ω to 4Ω). The R.I.P.S. System detects the actual load impedance, rather than relying on often inaccurate assumptions based on a speaker's rated impedance, and adjusts output rail voltages to deliver consistent output.

RealSink Heat Management: The large cast alloy heat sink's vertical fins are very effective at dissipating heat from the amplifier via convection and radiation. This design is achieved through extensive finite-element analysis, resulting in an amplifier that stays cool under demanding conditions. As an added cosmetic benefit, the cast-aluminum end-caps replicate half of a heat sink fin so that when two or more amplifiers are mounted end-to-end, you get a seamless custom look.

Advanced Rollback Protection: If a Slash v3 amplifier should ever reach an unsafe temperature, the Advanced Rollback Protection circuit reduces power until the amplifier cools down, without turning the music off completely.

Absolute Symmetry Class A/B Circuitry: The 300/4v3 amplifier benefits from patented Absolute Symmetry Class A/B Circuitry technology to maintain high fidelity with low distortion over a wide range of load impedances. The circuit employs identical N-Channel MOSFET transistors to push and pull the speaker with true buffering from the load impedance.

Differential-Balanced Inputs: The amplifier features differential-balanced input architecture to effectively control noise and ensure compatibility with a wide variety of source units, including many OEM systems. Without adding line output converters, you can directly connect most factory radios without creating any noise or compatibility issues. Unlike conventional single-ended inputs, the differential-balanced design does not connect one side of the audio signal to chassis ground, eliminating any voltage sensitivity between that terminal and ground, and greatly reducing the incidence of alternator whine in a typical car audio installation.

Protection Circuitry with Status Indicator Lights: There are three status indicator lights on the top of the amplifier:

  • Power (Green): lights green to indicate the amplifier is on and operating normally
  • Thermal (Red): lights to indicate the amplifier has exceeded its safe operating temperature, putting the amplifier into a shelf-protection mode, which reduces the power output of the amplifier; the red light will turn off and the amplifier will return to full-power operating mode when the internal temperature returns to a safe level
  • Low Ohm (Amber): lights to indicate the impedance of the speaker load is lower than optimum; when this light is on, a protection circuit engages and reduces the power output of the amplifier; the amber indicator will also light when a short-circuit is detected in the speaker wiring

Note: The only condition that will shut down the 300/4v3 completely is the battery voltage dropping below 10 volts.

Controls

Gain: The front and rear amplifier sections have independent gain controls, continuously variable from 200mV to 8V (200mV to 2V with the Input Voltage switch in the Low position, 800mV to 8V with the Input Voltage switch in the High position). The amplifier's R.I.P.S. feature also offers an easy way to optimize the gain setting. Because the amplifier will always deliver the same amount of power within its operational impedance range and supply voltage range, the maximum, unclipped output is predictable. This makes setting the gain level of the amplifier via the input sensitivity control very simple. All you need is digital AC voltmeter (item number 142TK12V, sold separately) and a test disc with a sine wave test tone recorded at 0 dB reference level in the frequency range to be amplified (item number 503CD104, sold separately).

Active Crossover: The front and rear amplifier sections also have independent crossover controls:

  • Filter Mode: three position switch; Off (full-range), LP(low-pass), or HP (high-pass)
  • Frequency: rotary dial, variable from 50 Hz to 500 Hz or 500 Hz to 5 kHz (depending on the frequency range switch)
  • Frequency Range: two position switch to specify the crossover frequency dial range; 50 Hz to 500 Hz (x1) or 500 Hz to 5 kHz (x10)
  • Filter Slope: two position switch to specify the crossover slope; 12dB/octave (Butterworth) or 24dB/octave (Linkwitz-Riley)

Input Mode: The amplifier's input mode switch allows you to choose between 4-channel and 2-channel mode. The 4-channel mode requires that two pair of RCA inputs be connected to the amplifier's front and rear inputs, while the 2-channel mode only requires one pair connected to the front inputs. Not front to rear fading is possible in the 2-channel mode.

Connections

Power and Ground: The amplifier's set-screw power and ground connections accept up to 4-gauge wire. JL Audio recommends 4-gauge for any power wire longer than six feet (8-gauge is acceptable if the power wire is shorter than six feet).

Note: The Amplifier is not equipped with an internal fuse. An external 40-amp fuse (not included) must be installed on the power wire. If the system has only this amp and a wiring kit is used that includes a fuse with a value other than 40-amps, the original should be replaced with a 40-amp fuse.

Remote Turn-On: The set-screw remote terminal accepts up to 8-gauge wire.

Speaker Outputs: The four pair of set-screw speaker terminals accept up to 8-gauge speaker wire.

Signal Input: The amplifier features two pair of stereo RCA inputs (front and rear). If no line level signal is available, you will need two speaker wire to RCA adaptors (item number 136XDCLR2S, sold separately) to connect the amplifier to the source unit via speaker wires.

Note: All inputs, outputs, and controls are located on the front side of the amplifier to make installation of the amplifier simple and neat.

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

JL Audio Slash 300/4v3 Reviews

Average Customer Review:

4 reviews
Review this product
Great Gear Giveaway

Submit a review and then enter to win a $500 rewards card

(0)
(0)
(0)
(0)
(0)

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
  Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left

Clean Power

Written By RockR, Cedar Hill, Tx on Thursday, October 02, 2014

Crutchfield Customer Review (What's this?)

I've been a fan of JL for quite some time. This was an upgrade from my V1 300/4. I have been no less than blown away with how clean and powerful these amps are.

Pros: Clean, quality workmanship, very versatile.

Cons: N/A

Excellent amp

Written By Michael, PA on Thursday, May 29, 2014

Crutchfield Customer Review (What's this?)

This amp has unbelievable sound. I hear details in music my previous Eclipse amp simply did not reproduce. No distortion at all and truly reference grade sound. However, this amp seems to have unusually powerful midbass, I had to tweak down my PEQ settings accordingly and I highly recommend using dynamat liberally.

Pros: Great sound, no audible distortion

Cons: Expensive

Another awesome product from JL Audio!!!!

Written By Mike, South Jersey on Thursday, March 13, 2014

I picked this amp up to upgrade my older JL Audio Slash 300/4 v1. I've been using JL Audio products in my Vehicle for about 10 years now. I'm using this amp to push a pair of Focal Integration speakers (temporary until I get the funds to get a pair of Focal K2's) and temporarily pushing a JL 10W7v2 with channels 3 and 4 bridged. This amp not only puts out amazing clear full range sound to the component speakers, but It is easily pushing that 10W7v2 without distortion or compromise despite the fact that it's only sending 150W to the sub!! Obviously this is temporary until I pick up the new 600/1v3 Slash which is gonna replace my 500/1v1 Slash which just gave out on me after 10 years! This amp is a beast and looks awsome with the powder black case. I couldn't be happier with this amp and I highly recommend this amp and any other JL product. You can't go wrong!!!

Pros: Awesome sound and top notch Circuitry JL amps output at least what they are rated at unlike most other brands Good price for what you get, Definitely worth every penny and more!!!

Cons: None

JL Amp rocks!

Written By Dave, Indianapolis on Sunday, September 15, 2013

Crutchfield Customer Review (What's this?)

Great amp. Worth the price. You always get what you pay for with JL Audio. Building a competition system. This amp drives 4 Alpine door speakers in a 2010 Highlander. Mounted underneath front passenger seat.

Pros: Rocks. No issues thus far.

Cons: None at this time.

Get everything you’ll need to enjoy your new JL Audio Slash 300/4v3

Bring the music from your amp to your speakers.
Patch cables take the music from your stereo to the amplifier. Most amp wiring kits don't include them.
For multi-amp systems, you'll need a separate fuse holder.
Helps protect your car's charging system and improves power handling. Required power and ground wires not included with cap.
The right tools will make the installation easier.
Kicker PK4

Kicker PK4

4-gauge amplifier power wiring kit

Item #: 206PK4

$129.99
Add to Cart
T-Spec 4PK Installation Kit

T-Spec 4PK Installation Kit

4-gauge amplifier wiring kit — includes speaker wire

Item #: 1204PK

(3)

$89.99
Add to Cart
Rockford Fosgate RFK4X

Rockford Fosgate RFK4X

Complete 4-gauge amplifier wiring kit
Includes patch cable and speaker wire

Item #: 575RFK4X

(12)

$159.99
Add to Cart
EFX PA4BX Wiring Kit

EFX PA4BX Wiring Kit

4-gauge amplifier wiring kit — includes 2-channel patch cable

Item #: 142PA4BX

(5)

$79.99
Add to Cart
Rockford Fosgate RFK4

Rockford Fosgate RFK4

4-gauge amplifier power wiring kit

Item #: 575RFK4

(10)

$114.99
Add to Cart
T-Spec V10-RAK4

T-Spec V10-RAK4

4-gauge amplifier wiring kit — includes 2-channel patch cable

Item #: 120V10RAK4

(1)

$99.99
Add to Cart
Kicker CK4

Kicker CK4

Complete 4-gauge amplifier wiring kit — includes 2-channel patch cable and speaker wire

Item #: 206CK4

$149.99
Add to Cart
Lightning Audio LA-4i

Lightning Audio LA-4i

4-gauge amplifier wiring kit — includes 2-channel patch cable

Item #: 495LA4I

(7)

$69.99
Add to Cart
T-Spec 16-gauge Speaker Wire

T-Spec 16-gauge Speaker Wire

Black/white jacket — priced per foot

Item #: 120SW16WB1

(13)

T-Spec 12-gauge Speaker Wire

T-Spec 12-gauge Speaker Wire

Black/white jacket — priced per foot

Item #: 120SW12WB1

(30)

Stinger PRO Series Speaker Wire

Stinger PRO Series Speaker Wire

Priced per foot (16 Gauge)

Item #: 541SPW516B

(51)

JL Audio XD-CLRAIC2-SW

JL Audio XD-CLRAIC2-SW

2-channel speaker output converter (bare speaker wires to male RCAs)

Item #: 136XDCLR2S

(12)

T-Spec 2-Channel RCA Patch Cables

T-Spec 2-Channel RCA Patch Cables

Available in 7 different lengths (20-foot)

Item #: 120RCA202

(27)

$20.99
Add to Cart
T-Spec 4-Channel RCA Patch Cable

T-Spec 4-Channel RCA Patch Cable

17-foot length

Item #: 120RCA174

(8)

$29.99
Add to Cart
EFX 17-foot RCA Patch Cable

EFX 17-foot RCA Patch Cable

Item #: 142A17C

(55)

$7.99
After $2.00 Savings Add to Cart
EFX CFHG4 Fuse Holder

EFX CFHG4 Fuse Holder

In-line AGU fuse holder accepts 4- to 8-gauge wire

Item #: 142CFHG4

Rockford Fosgate RFFAGU Fuse Holder

Rockford Fosgate RFFAGU Fuse Holder

Platinum-plated AGU fuse holder
Fits 4- or 8-gauge cable

Item #: 575RFFAGU

(25)

$10.99
Add to Cart
T-Spec Capacitor

T-Spec Capacitor

1.5-farad capacitor with red LCD meter

Item #: 12015DDC

(11)

$79.99
Add to Cart
Pro.Fit Wire Worm

Pro.Fit Wire Worm

Installation tool helps route wiring through tight spaces

Item #: 042DM4533

(33)

$12.99
Add to Cart
S&G Wire Cutter/Stripper Tool

S&G Wire Cutter/Stripper Tool

Cuts and strips 12- to 22-gauge wire

Item #: 18119100

(15)

$19.99
Add to Cart
Bojo Trim Panel Tools

Bojo Trim Panel Tools

Set of 6 pry tools — helps remove interior and exterior trim and door panels

Item #: 126CR6NGL

(52)

$24.99
Add to Cart
Bojo Trim Panel Tools

Bojo Trim Panel Tools

Set of 6 pry tools — helps remove interior and exterior trim and door panels

Item #: 126CR6LNGL

(2)

$29.99
Add to Cart
DEI Heat Shrink Tubing

DEI Heat Shrink Tubing

Black 4-foot length (Assortment)

Item #: 696010839

(7)

$24.99
Add to Cart

Questions & Answers Ask the community. Share your knowledge.