About the JL Audio J2 360.2
JL Audio's J2 amplifiers will electrify you with strong performance at an affordable price, as these high-powered amps transform your system with their superb sound quality. Oversized output transistors, extra-quiet input circuitry, and high-tech power supplies deliver strong, stable output and reliable performance. These amps are overbuilt and underrated, so you'll get the maximum clean power you'd expect from JL Audio.
The J2 360.2 2-channel amp delivers 110 watts RMS per channel to your speaker system, a great match for a high-quality set of component speakers or you can switch over to mono mode to send 360 watts RMS to a sub. You can use the frequency filters and bass boost to tune your amp's sound to match your speaker system perfectly. Preamp outputs send the signal to a second amp in your system, so you don't have to run a second set of patch cables from your receiver.
Product highlights:
- 2-channel car amplifier
- 110 watts RMS x 2 at 4 ohms (180 watts RMS x 2 at 2 ohms)
- 360 watts RMS x 1 at 4 ohms
- Class AB amplifier design
- MOSFET switching power supply
- frequency response: 10-35K Hz
- variable high- and low-pass filter (50-500 Hz, 12 dB/octave)
- variable bass boost (0-9 dB at 45 Hz)
- preamp inputs and outputs
- speaker-level inputs
- fuse rating: 20A x 2
- 4-gauge power and ground leads and a 40-amp fuse recommended wiring and hardware not included with amplifier
- 12-13/16"W x 2-3/16"H x 9-5/8"D
- warranty: 1 year
- MFR # 99394
What's in the box:
JL Audio J2 360.2 owner's manual
- 2-Channel full-range amplifier
- Four 20 amp ATO fuses (2 installed)
- 2mm Allen wrench
- 2.5mm Allen wrench
- 3mm Allen wrench
- 10" Speaker input harness
- Four 3/4" Self-tapping screws
- 4 Flat washers
- Owner's manual
Customer reviews for JL Audio J2 360.2
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the JL Audio J2 360.2
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
110 x 2 | |
Peak Power Output (Watts x Channels) | N/A | |
Power at 2 Ohms (Watts x Channels) | 180 x 2 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 360 x 1 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-35k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | N/A | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | AB | |
Low-Pass Crossover Frequency | 50-500 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | 50-500 Hz | |
High-Pass Slope (dB/octave) | 12 dB/oct | |
Bass Boost | 0-9 dB | |
Bass Boost Frequency | 45 Hz | |
Fan Cooled | No | |
Fuse Rating | 20 x 2 | |
Speaker Level Inputs | --- | |
Preamp Outputs | 1 pair | |
Width (inches) | 13-5/16 | |
Height (inches) | 2-3/16 | |
Depth (inches) | 9-11/16 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Features
Stereo Amplifier: The JL Audio J2 360.2 is a class A/B stereo amplifier rated at 110 watts RMS x 2 into a 4Ω load, 135 watts RMS x 2 into a 3Ω load, and 180 watts RMS x 2 into a 2Ω load. When bridged the output is 360 watts RMS x 1 into a 4Ω load, 270 watts RMS x 1 into a 6Ω load, and 220 watts RMS x 1 into an 8Ω load.
Status LEDs: There are two LEDs on the left side of the amplifier:
- Power: green LED indicates the amplifier is turned on and operating normally
- Protect: red LED indicates the amplifier has exceeded its safe operating temperature, detected a short in a speaker output, or the speaker impedance is too low
Controls
Active Crossover: The crossover can be set to high-pass, low-pass, or off (full range). The crossover point is continuously variable from 50 Hz to 500 Hz and the crossover slope is 12 dB/octave.
Bass Boost: The bass boost circuit is adjustable from 0 to +9 dB. The boost frequency is fixed at 45 Hz.
Connections
Power and Ground: The Power and Ground connections accept 4 gauge wire, which JL Audio recommends as the minimum size. The set-screw terminals are tightened/loosened using the included 3mm Allen wrench.
Remote Turn-On: The remote terminal will accept 10 to 18 gauge wire. The set-screw terminal is tightened/loosened using the included 2mm Allen wrench.
Speaker Outputs: The speakers' set-screw terminals will accept 8 to 16 gauge speaker wire; they are tightened/loosened using the included 2.5mm Allen wrench.
Preamp Inputs: The amplifier features one set of RCA line level inputs. The input sensitivity is adjustable from 200mV to 4V RMS.
Speaker Inputs: When connecting the amp to a head unit without line level outputs, use the included speaker level input harness. In this case the input sensitivity is adjustable from 2V to 10V RMS.
Preamp Outputs: There is a pair of preamp outputs so you can send audio to another amplifier in your system. The preamp output is not affected by the crossover or bass boost circuits.
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Great little amp. Pushing 1, 12" BA G2 and it pounds. It's half the size of the amp I was previously using, looks great, stays very cool on a bridged 4 ohm load and is worth the $170 bucks. It isn't JL's top of the line gear but the quality is there and the name is one we all trust!
Dave from San Diego