Skip Navigation

Kicker 11DX200.4

4-channel car amplifier — 25 watts RMS x 4

1 Review | 1 question - 1 answer

Item #: 20611DX2K4

This item is no longer available.

Original Price: $139.99

Shop all Car Amplifiers

Add to Cart

Kicker 11DX200.4

Overview

Our take on the Kicker 11DX200.4

For some people, great music is what makes life worth living. Kicker built their DX200.4 4-channel amp to send 25 watts RMS to each of your car's speakers — about double the power of most factory and many aftermarket receivers — so you can feel the musical joy too. And all from an amp with a footprint less than the size of a piece of computer paper.

Boost your music's power

For some people, great music is what makes life worth living. Kicker built their DX200.4 4-channel amp to send 25 watts RMS to each of your car's speakers — about double the power of most factory and many aftermarket receivers — so you can feel the musical joy too. And all from an amp with a footprint less than the size of a piece of computer paper.

You can also switch this versatile amp into 2-channel mode to run a pair of high-performance components with 100 watts RMS of goodness each. You can harness this power with built-in high- and low-pass filters that tailor the notes to fit your speakers. Independent front and rear bass boosts lets you add some extra bump to your tunes.

Isolates and eliminates noise

You want lots of power for your speakers, but this Kicker DX amp gives you something extra — clean power. Kicker's FIT™ — Fail-Safe Integration Technology — rejects noise from alternators, audio/video gear, and other car electronics for crisp, clean operation, and accepts a wide range of signals so you can hook up the DX200.4 to almost any stereo.

DX200.4 control panel

Swapped out an old generic amp for this kicker amp. so much better sound and no more engine whine coming through

Ty, cincinnati oh

What's in the Box:

  • 4-Channel amplifier
  • Two 30-Amp ATO blade fuses (1 installed/1 spare)
  • Two 4-gauge crimp-on barrier spade connectors
  • Eight 12-gauge crimp-on barrier spade connectors
  • One 14-gauge crimp-on barrier spade connector
  • Four 3/4" Self-tapping screws
  • Eight 16-22 Gauge butt connectors
  • Owner's manual (English/ Spanish/ German/ French)
  • Power certification sheet

Product Highlights:

  • 4-channel car amplifier
  • 25 watts RMS x 4 at 4 ohms (50 watts RMS x 4 at 2 ohms)
  • 100 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode)
  • CEA-2006 compliant
  • selectable low-pass filters (80 Hz, 18 dB/octave)
  • selectable high-pass filters (100 Hz, 18 dB/octave)
  • selectable bass boosts (0, 9 dB at 40 Hz)
  • Class AB amp technology
  • differential-balanced inputs eliminate noise from your vehicle's electrical system
  • preamp and speaker-level inputs (speaker wire to RCA adapter required for speaker-level input)
  • 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • fuse rating: 30A x 1
  • 10-1/2"W x 2-1/4"H x 8-5/16"D
  • warranty: 2 years (extends to 3 years when purchased with either a Kicker single amp wiring kit or a Kicker multi-amp kit)
  • Our 60-day money-back guarantee
Reviews

Kicker 11DX200.4 Reviews

Average Customer Review:

1 Review

great amp

Written by: Ty from cincinnati oh on June 15, 2013

Crutchfield Customer Review (What's this?)

Swapped out an old generic amp for this kicker amp. so much better sound and no more engine whine coming through

Pros: High low settings are great if you have an equalizer or no low outputs on the head unit

Cons: terminals are designed to not lose the screws but they make it harder to put the wire terminals in it

Details

Hands-on research

What's in the box?

Download the Kicker 11DX200.4 manual

  • 4-Channel amplifier
  • Two 30-Amp ATO blade fuses (1 installed/1 spare)
  • Two 4-gauge crimp-on barrier spade connectors
  • Eight 12-gauge crimp-on barrier spade connectors
  • One 14-gauge crimp-on barrier spade connector
  • Four 3/4" Self-tapping screws
  • Eight 16-22 Gauge butt connectors
  • Owner's manual (English/ Spanish/ German/ French)
  • Power certification sheet

Product Research

Features
Controls
Connections
Warranty

Features

CEA 2006 Compliant: The Kicker DX200.4's power and signal to noise ratio are measured according to CEA 2006 standards (Consumer Electronics Association). These standards allow you to accurately compare the specifications of all CEA 2006-compliant amplifiers, even if they are different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging. The rated power output is 25 watts RMS x 4 channels into 4Ω (20 Hz-20 kHz, <1% THD+N). While the CEA 2006 S/N is 85 dB (measured at 1 watt), the S/N at rated power is >95 dB.

Kicker Livin' Loud Certified Power: The amplifier comes with a certificate that indicates the total maximum wattage of the particular amplifier, along with the model number, serial number, tested date, and whether the amplifier passed the total harmonic distortion, signal-to-noise ratio, and protection circuit tests.

Protection Circuitry: The DX200.4 has protection circuitry that will turn the amp off in the event of overheating, over voltage (power input), under voltage (power input), short circuit (speaker output), and over current (speaker output). If the Protection LED on the left side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.

Fail-Safe Integration Technology (FIT): To accommodate the varying range of signal levels coming from today's factory and aftermarket radios, the DX200.4 utilizes Fail-Safe Integration Technology (FIT), offering isolated differential inputs for significant noise reduction, and compatibility with virtually any factory radio.

Speaker Level Input: High level inputs can be used when the source device doesn't have preamp level outputs. The same RCA inputs on the amp are used for either speaker level or line level connections. When a speaker level signal is used, speaker wire to RCA adapters are needed (item number 206KISL, sold separately) and the Input Level should be set to High.

Controls

Gain Control: The front and rear sections of the amp have independent input gain controls. With the Input Level Control switch at the appropriate setting, you can set the rotary Gain Control to match the output of the source unit. The Gain Controls are adjusted with a flat-head screwdriver and can be set between 0 and 11.

Input Level: The input level control is switchable; when set to Low, the amp can accommodate a line level input signal of 125mV-5V, on High, the amp will accept a 250mV-10V speaker level signal.

Auto Turn-On: The Auto Turn-On switch offers three options:

  • +12 V: the amp turns on when +12 volts is applied to the remote terminal
  • DC Offset: the amp turns on when a 6 volt surge is detected on the signal inputs (from a speaker level source); in this mode the amp's remote terminal acts as a +12 volt output to turn on another component
  • Audio: the amp turns on when an incoming audio signal is detected; in this mode the amp's remote terminal acts as a +12 volt output to turn on another component

Crossover: The front and rear amplifier channels have independent crossover settings and can be set for low-pass, high-pass, or full-range operation. The low-pass crossover points are 80 Hz and the high-pass crossover points are 100 Hz; the crossover slope is 18 dB per octave.

KICKEQ Bass Boost: The front and rear amplifier channels have independent bass boost switches (on/off). The bass boost circuits provide a +9 dB signal boost at 40 Hz.

Fader: When powering four speakers and using both the front and rear inputs, turn the fader switch On to maintain front/rear fader control.

Connections

Left Side of Amplifier:

  • +12V (power): screw terminal; accepts spade connector up to 0.5" wide
  • REM (remote turn-on): screw terminal; accepts spade connector up to 0.325" wide
  • GND (ground): screw terminal; accepts spade connector up to 0.5" wide
  • Speaker Outputs: four pair of screw terminals; accept spade connectors up to 0.325" wide
  • Fuse: 30-amp ATO fuse (factory installed)

Right Side of Amplifier:

  • RCA Inputs: two pair of RCA input jacks, front and rear

Warranty

Extended Warranty: Kicker will add a year to the standard two year warranty (for a total of three years) when any matching Kicker amplifier wiring kit is used with this amp (8 gauge minimum). Both the amp and wiring kit should be purchased on the same order and the usual warranty limitations apply (covers manufacturing defects, must be purchased from an authorized Kicker dealer, etc.).

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Accessories
Q & A

Customer Q&A

1 question already asked

Thanks for your question. For information on selecting the best amp for your subs I would recommend reaching out to an Advisor by phone (1-800-324-9695) or online chat. They will be able to help determine the differences between the amp models and help you make the best choice for your system. [ Krissy  May 26, 2014 ]  Staff
Library