About the Kicker 11ZX300.1
Big bass
Big bass
This Kicker ZX300.1 mono subwoofer amplifier pumps your bass up loud and clear with up to 300 watts RMS of power. This sub amp runs reliably even when pushed hard, thanks to its heavy-duty internal components and the efficient cooling system it uses as it boosts your bass.
Works with almost any stereo
Kicker employs their Fail-Safe Integration Technology™ (FIT) to reject noise and stop any interference generated by your car's electronics, so you'll enjoy your music clean and pure. Speaker-level inputs make it simpler to hook this amp up to your factory system.
Bass controls
The steeply-sloped subsonic and low-pass filters keep the bass tight and up front in your car. A bass boost gives you even more kick, if you so desire. Be sure to get the optional wired remote level controller so you can crank up the level of fun from the front seat.
Confused about impedance? Check out our article on matching subs and amps.
Product highlights:
- mono subwoofer amplifier
- 150 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- low-pass filter (80 Hz, 24 dB/octave)
- fixed subsonic filter (25 Hz, 24 dB/octave)
- switchable bass boost (12 dB at 40 Hz)
- Class AB amp technology
- Fail-Safe Integration Technology eliminates noise from your vehicle's electrical system
- preamp and speaker-level inputs (speaker-level input requires an optional adapter)
- preamp outputs
- optional wired ZXRC Remote Bass Control available
- 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- fuse rating: 20A x 2
- 13-1/2"W x 2-1/8"H x 9-5/8"D
- warranty: 2 years (extends to 3 years when purchased with either a Kicker single amp wiring kit or a Kicker multi-amp kit)
- MFR # 11ZX3001
What's in the box:
Kicker 11ZX300.1 owner's manual
- Mono amplifier
- Owner's manual (English/ Spanish/ German/ French)
Customer reviews for Kicker 11ZX300.1
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kicker 11ZX300.1
Features & specs
| Performance | ||
|---|---|---|
| RMS Power Output (Watts x Channels) |
150 x 1 | |
| Peak Power Output (Watts x Channels) | N/A | |
| Power at 2 Ohms (Watts x Channels) | 300 x 1 | |
| Power at 1 Ohm (Watts x Channels) | --- | |
| Bridged Power (Watts x Channels) | N/A | |
| Minimum Impedance Bridged | N/A | |
| Minimum Impedance Unbridged | 2 | |
| Minimum Impedance | 2 | |
| Best Frequency Response | 25-20k Hz | |
| THD at Rated RMS Power | 1% | |
| Signal to Noise Ratio | 96 dB | |
| Input Voltage | 14.4v | |
| Features | ||
| Amplifier Class | AB | |
| Low-Pass Crossover Frequency | 80 Hz | |
| Low-Pass Slope (dB/octave) | 24 dB/octave | |
| High-Pass Crossover Frequency | N/A | |
| High-Pass Slope (dB/octave) | N/A | |
| Bass Boost | 0, 12 dB | |
| Bass Boost Frequency | 40 Hz | |
| Fan Cooled | No | |
| Fuse Rating | 40 | |
| Speaker Level Inputs | --- | |
| Preamp Outputs | 1 pair | |
| Width (inches) | 13-1/2 | |
| Height (inches) | 2-1/8 | |
| Depth (inches) | 9-5/8 | |
| Parts Warranty | 2 Year | |
| Labor Warranty | 2 Year | |
Product Research
Controls
Gain: The rotary gain control is continuously variable from 125 mV to 5 V when the Input Sensitivity switch is set to Low and 250 mV to 10 V when the Input Sensitivity switch is set to High.
Crossover: The crossover can be set to low-pass or off (full-range). The crossover point is fixed at 80 Hz and the slope is 24dB per octave.
Auto Turn-on Switch: The amp offers three automatic turn-on modes; select from:
- +12V: connect a wire from the remote turn-on lead from your source unit to the REM terminal on the amplifier; this is the preferred turn-on method
- DC Offset: turns the amp on when a 6-volt DC offset is detected at the high-level speaker inputs when the source unit is turned on
- Audio: detects the incoming audio signal from your source unit and automatically turns the amp on; will not work if the input gain control is not set properly
Bass Boost: The bass boost circuit provides a 12 dB boost at 40Hz. The bass boost can be turned off if you prefer.
ZXRC Remote Bass Control: The bass output level can be controlled remotely using an optional wired remote bass control (item number 20610ZXRC, sold separately).
Connections
Left Side of Amplifier:
- +12V (power): set screw terminal
- REM (remote turn-on): set screw terminal
- GND (ground): set screw terminal
- Fuses: two 20-amp ATO fuses
Right Side of Amplifier:
- Speaker Outputs: one pair of set screw terminals
- RCA Input: one pair of stereo RCA input jacks; also used for speaker level input (item number 20609ZiSL needed, sold separately)
- RCA Output: one pair of stereo RCA output jacks
Amp Wiring Kit: Kicker recommends using a 8-gauge wiring kit with this amplifier.
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
I installed this amp which is powering the Boston Acoustics G110PD. It sounds much better now in my '02 Rodeo.
Jeff S from Athens, TN