About the Kicker DXA125.2
Power your music
Power your music
Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..
Works with a factory stereo
Kicker's Fail-Safe Integration Technology (FIT™) allows you to tap into your vehicle's factory speaker wiring for the amp's input signals without needing a converter. The "differential-balanced" inputs also help prevent audio interference and noise from entering the system.
DXA125.2 input and control panel
Tone controls to help get the job done
The DXA125.2 features separate controls that work with a variety of different speakers or subs. A high-pass filter clears out rumble from small speakers so they can play more efficiently, while a low-pass filter adjusts the bass frequencies going to your sub, so it'll play cleanly. The bass boost can add some extra foundation to the sound if you want.
Product highlights:
- 2-channel car amplifier
- 30 watts RMS x 2 at 4 ohms (60 watts RMS x 2 at 2 ohms)
- 125 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode)
- CEA-2006 compliant
- variable high- and low-pass filters (50-200 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 40 Hz)
- Class AB amp technology
- differential-balanced inputs eliminate noise from your vehicle's electrical system
- preamp and speaker-level inputs
- speaker-level inputs (require speaker wire to RCA adapters)
Other Features
- 8-gauge power and ground leads and a 40-amp fuse recommended wiring and hardware not included with amplifier
- no onboard fuses — when installing multiple amps in a system, an additional 40-amp in-line fuse between the distribution block and the amplifier is recommended
- 8-3/16"W x 2-3/8"H x 7-1/8"D
- warranty: 2 years (extends to 3 years when purchased with a Kicker 8-gauge amp kit or multi-amp kit)
- MFR # 41DXA1252
What's in the box:
Kicker DXA125.2 owner's manual
- Two-channel amplifier
- Four 3/4" #8 self-tapping screws
- Owner's Manual
Customer reviews for Kicker DXA125.2
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kicker DXA125.2
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
30 x 2 | |
Peak Power Output (Watts x Channels) | 250 x 1 | |
Power at 2 Ohms (Watts x Channels) | 60 x 2 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 125 x 1 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-20000 Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 95 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | AB | |
Low-Pass Crossover Frequency | 50-200 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/octave | |
High-Pass Crossover Frequency | 50-200 Hz | |
High-Pass Slope (dB/octave) | 12 dB/octave | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 40 Hz | |
Fan Cooled | No | |
Fuse Rating | 40 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 8-3/16 | |
Height (inches) | 2-3/8 | |
Depth (inches) | 7-1/8 | |
Parts Warranty | 2 Years | |
Labor Warranty | 2 Years |
Product Research
Features
Controls
Installation
Connections
Features
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over the full frequency range of the amp with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels at a reference of 1 watt. CEA-2006 allows consumers to compare car amplifiers and receivers on equal footing. Measured under CEA-2006 conditions the Kicker DXA125.2 is rated at 30 watts RMS x 2 channels into a 4-ohm load and the signal to noise ratio is >95 dB. Additional specs listed in the manual (but not listed as CEA-2006 compliant) include 60 watts RMS x 2 channel into a 2-ohm load (measured using a 14.4 volt power supply with no more than 1% THD+N) and 95 dB signal-to-noise ratio (measured at the rated power output).
Auto Turn-On: There are two ways to automatically turn on the amplifier. Most aftermarket car stereo head units will have a remote turn-on lead, which can be extended to the amplifier location and connected to the amp's Remote terminal. If connecting the amplifier to a factory stereo, or a head unit without a remote turn-on lead, the amp can automatically turn on using the DC Offset mode. The amp detects a 6-volt DC surge on the signal inputs and turns the amplifier on. There is no switch on the amp to select the Turn-On method.
Protection Circuitry: The DXA125.2 has protection circuitry that will turn the amp off in the event of overheating, over voltage (over 16 volt input), under voltage (under 10 volt input), and short circuit (speaker output). If the Protection LED on the right side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.
Dual Input Sensitivity: The DXA125.2 can receive low- or high-level signals from your car stereo source unit at the amplifier's left and right RCA inputs. The low-level signal can be sent from the source unit's RCA line-level outputs. In this case, the Input Sensitivity switch on the amp should be set to "LO". A high-level signal can come from the source unit's speaker outputs, and connected to the amplifier using the Kicker KISL adapters. The Input Level switch should be set to "HI".
Fail-Safe Integration Technology (FIT): FIT utilizes isolated differential inputs, rejecting noise and electrical interference for the quietest operation possible. FIT also allows Kicker amps to accept output from nearly any factory or aftermarket head unit.
Stereo-and-Mono-Simultaneously (SAMS): The amp has the capability of powering a pair of full-range speakers and a mono subwoofer from one pair of channels. Using passive crossovers, you can high-pass the signals to the full-range speakers and to low-pass the signals to the subwoofers. The SAMS wiring diagram can be found in the Owner's Manual.
Controls
Input Level: The DXA125.2 has a two position (in/out) switch to set the input level type. It can be pressed in for High (for speaker level) or set to out for Low (for line level).
Gain: The input gain is continuously variable, labeled 0 to 11. The gain range is governed by the input level switch: 250mV to 10V for speaker level (HI) and 125mV to 5V for line level (LO). A small screwdriver is needed to adjust the gain.
Crossover Frequency: The crossover can be set for low-pass (LO), high-pass (HI), or full-range operation (OFF). The crossover frequency range is continuously variable between 50 Hz and 200 Hz. The crossover slope is 12 dB per octave A small screwdriver is needed to set the crossover cutoff frequency.
KickEQ Bass Boost: The KickEQ bass boost circuit provides a signal boost centered at 40 Hz. The bass boost is continuously variable between 0 and 12dB. A small screwdriver is needed to adjust the amount of bass boost.
Installation
Wiring Recommendations: Kicker recommends that the amplifier be connected to the vehicle's battery using 8 Gauge power and ground wiring. An external 40 amp fuse should be installed on the power wire within 18" of the battery. There are no fuses included or built into the amplifier.
Kicker Extended Warranty Offer: Kicker will extend the amp's standard warranty by an additional year (for a total warranty of three years) when it is installed with a qualifying Kicker amplifier installation kit. Kicker recommends the PK8, CK8, or ZCK84 wiring kit for this amp. The amplifier and installation kit must be purchased from an authorized Kicker dealer.
Connections
Left Side of Amplifier:
- GND (ground): screw terminal; accepts spade connector up to 0.5" wide
- REM (remote turn-on): screw terminal; accepts spade connector up to 0.33" wide
- +12V (power): screw terminal; accepts spade connector up to 0.5" wide
- Speaker Outputs: two pairs of screw terminals; accepts spade connectors up to 0.32" wide
Right Side of Amplifier:
- RCA Inputs: one pair of RCA jacks, used for line level or speaker level inputs with KISL
The Kicker DXA125.2 replaces these items
Kicker 11DX125.2
- 125 watts RMS x 1 bridged at 4 ohms
- selectable high- and low-pass filters
- Class AB amp technology
Loading...
Loading accessories...
Customer Q&A
2 questions already asked
Loading...
Loading articles...
I am using 2 of this amps, 2 kicker 6x9 and 1 kicker 10" sub on a boom box, and of course a Bluetooth receiver and an eq. A marine battery provides the juice to this setup and runs for hours. This is a great way to listen to your iphone pretty loud and clear.
HG from Texas