Chat
Contact us
Close contact box
Connect ID #
637 236 387 4
Connect ID #
637 236 387 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Kicker DXA250.4 4-channel car amplifier — 30 watts RMS x 4

Item # 20641D2504

Kicker's DXA250.4 4-channel amplifier will reliably produce great-sounding music, delivering 30 watts RMS to...

Find what Fits your vehicle

Remove

Checking fit...

Kicker's DXA250.4 4-channel amplifier will reliably produce great-sounding music, delivering 30 watts RMS to...

2 questions - 2 answers

Item # 20641D2504

Shop all Kicker Car Amplifiers

About the Kicker DXA250.4

Buck Pomerantz

Power your music

Kicker's DXA250.4 4-channel amplifier will reliably produce great-sounding music, delivering 30 watts RMS to each of your speakers from a very compact chassis that'll fit in almost any vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the front channels on the DXA250.4 to power your front speaker, then bridge the rear channels together to power a subwoofer with 125 watts RMS.

Power your music

Kicker's DXA250.4 4-channel amplifier will reliably produce great-sounding music, delivering 30 watts RMS to each of your speakers from a very compact chassis that'll fit in almost any vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the front channels on the DXA250.4 to power your front speaker, then bridge the rear channels together to power a subwoofer with 125 watts RMS.

Works with a factory stereo

Kicker's Fail-Safe Integration Technology (FIT™) allows you to tap into your vehicle's factory speaker wiring for the amp's input signals without needing a converter. If your car stereo only has one set of preamp outputs, the DXA250.4 can apply the signal to its other channels to achieve 4-channel play. The "differential-balanced" inputs also help prevent audio interference and noise from entering the system.

Kicker DXA250.4

DXA250.4 input and control panel

Tone controls to help get the job done

The DXA250.4 features separate controls for the front and rear channels so it can work with a variety of different speakers or subs. High-pass filters clear out rumble from small speakers so they can play more efficiently, while low-pass filters adjusts the bass frequencies going to your subs, so they'll play cleanly. Bass boosts on the front and rear channels add some extra foundation to the sound if you want.

READ LESS

Product highlights:

  • 4-channel car amplifier
  • 30 watts RMS x 4 at 4 ohms (60 watts RMS x 4 at 2 ohms)
  • 125 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode)
  • CEA-2006 compliant
  • variable high- and low-pass filters (50-200 Hz, 12 dB/octave)
  • variable bass boost (0-12 dB at 40 Hz)
  • Class AB amp technology
  • differential-balanced inputs eliminate noise from your vehicle's electrical system
  • preamp and speaker-level inputs
  • speaker-level inputs (require speaker wire to RCA adapters)
Other Features
  • 8-gauge power and ground leads and a 60-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 60-amp in-line fuse between the distribution block and the amplifier is recommended
  • 12"W x 2-3/8"H x 7-1/8"D
  • warranty: 2 years (extends to 3 years when purchased with a Kicker 8-gauge amp kit or multi-amp kit)
  • MFR # 41DXA2504

What's in the box:

  • Four-channel amplifier
  • Four 3/4" #8 self-tapping screws
  • Owner's Manual

Customer reviews for Kicker DXA250.4

Loading reviews...

Average review:

4.5 out of 5 stars
6 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Customer provided image, click to load a larger version.
Customer provided image, click to load a larger version.

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee review (What's this?)

Reviewed on Samsung.com

This review was collected as part of a promotion

Pros:

Cons:

Crutchfield response
Customer provided image, click to load a larger version.
<< >>

More details on the Kicker DXA250.4

Mark G.

Product Research

Features
Controls
Installation
Connections

Features

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over the full frequency range of the amp with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels at a reference of 1 watt. CEA-2006 allows consumers to compare car amplifiers and receivers on equal footing. Measured under CEA-2006 conditions the Kicker DXA250.4 is rated at 30 watts RMS x 4 channels into a 4-ohm load and the signal to noise ratio is >95 dB. Additional specs listed in the manual (but not listed as CEA-2006 compliant) include 60 watts RMS x 4 channel into a 2-ohm load (measured using a 14.4 volt power supply with no more than 1% THD+N) and 95 dB signal-to-noise ratio (measured at the rated power output).

Auto Turn-On: There are two ways to automatically turn on the amplifier. Most aftermarket car stereo head units will have a remote turn-on lead, which can be extended to the amplifier location and connected to the amp's Remote terminal. If connecting the amplifier to a factory stereo, or a head unit without a remote turn-on lead, the amp can automatically turn on using the DC Offset mode. The amp detects a 6-volt DC surge on the signal inputs and turns the amplifier on. There is no switch on the amp to select the Turn-On method.

Protection Circuitry: The DXA250.4 has protection circuitry that will turn the amp off in the event of overheating, over voltage (over 16 volt input), under voltage (under 10 volt input), and short circuit (speaker output). If the Protection LED on the right side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.

Dual Input Sensitivity: The DXA250.4 can receive low- or high-level signals from your car stereo source unit at the amplifier's left and right, RCA inputs. The low-level signal can be sent from the source unit's RCA line-level outputs. In this case, the Input Sensitivity switch on the amp should be set to "LO". A high-level signal can come from the source unit's speaker outputs, and connected to the amplifier using the Kicker KISL adapters. The Input Level switch should be set to "HI".

Fail-Safe Integration Technology (FIT): FIT utilizes isolated differential inputs, rejecting noise and electrical interference for the quietest operation possible. FIT also allows Kicker amps to accept output from nearly any factory or aftermarket head unit.

Stereo-and-Mono-Simultaneously (SAMS): The amp has the capability of powering a pair of full-range speakers and a mono subwoofer from one amplifier. The full-range can be connected normally on one pair of channels, while the subwoofer (4 ohms) can be powered by bridging the remaining pair of channels. The SAMS wiring diagram can be found in the Owner's Manual.

Controls

Input Level: The The DXA250.4 has a two position (in/out) switch to set the input level type. It can be pressed in for High (for speaker level) or set to out for Low (for line level). You should not mix low and high inputs signals to the amp.

Fader Switch: This 4-channel amplifier can accept signals from one or two sets of inputs. If you are running two sets (front and back), the amp's Fader switch should be pressed in to the ON position. If you want to drive all four channels from one set of inputs, the switch should be left in the OFF position. With the fader Off, the four channels will receive the same volume of signal, and you will not be able to adjust the fader front to back.

Audio Controls: The amplifier has two independent pairs of channels (labeled Amp 1 and Amp 2), each with separate controls. A small screwdriver is needed to set the rotary controls. Amp 1 and Amp 2 have the following controls:

  • Gain: The input gain is continuously variable, labeled 0 to 11. The gain range is governed by the input level switch: 250mV to 10V for speaker level (HI) and 125mV to 5V for line level (LO).
  • Crossover Frequency: Each crossover can be set for low-pass (LO), high-pass (HI), or full-range operation (OFF). The crossover frequency range is continuously variable between 50 Hz and 200 Hz. The crossover slope is 12 dB per octave. It is possible to set one crossover to low-pass and the other to high-pass.
  • KickEQ Bass Boost: The KickEQ bass boost circuit provides a signal boost centered at 40 Hz. The bass boost is continuously variable between 0 and 12dB.
Installation

Wiring Recommendations: Kicker recommends that the amplifier be connected to the vehicle's battery using 8 Gauge power and ground wiring. An external 60 amp fuse should be installed on the power wire within 18" of the battery. There are no fuses included or built into the amplifier.

Kicker Extended Warranty Offer: Kicker will extend the amp's standard warranty by an additional year (for a total warranty of three years) when it is installed with a qualifying Kicker amplifier installation kit. Kicker recommends the PK8, CK8, or ZCK84 wiring kit for this amp. The amplifier and installation kit must be purchased from an authorized Kicker dealer.

Connections

Left Side of Amplifier:

  • GND (ground): screw terminal; accepts spade connector up to 0.5" wide
  • REM (remote turn-on): screw terminal; accepts spade connector up to 0.33" wide
  • +12V (power): screw terminal; accepts spade connector up to 0.5" wide
  • Speaker Outputs: four pairs of screw terminals; accepts spade connectors up to 0.32" wide

Right Side of Amplifier:

  • RCA Inputs: two pairs of RCA jacks, used for line level or speaker level inputs with KISL

Loading accessories...

Customer Q&A

2 questions already asked

Q
Will this unit handle 4 100 watt Rms 300watt peak speakers?
whitie  Apr 01, 2017
1 answer
A
Thanks for your question. For information on selecting the best amp for your speakers I would recommend reaching out to an Advisor by phone (1-800-324-9695) or online chat. They will be able to help determine the differences between the amp models and help you make the best choice for your system.
kenneth  Apr 01, 2017 (Staff)
Q
You have a CEA-2006 compliant 95db Signal to Noise ratio listed for this amplifier. That seems too good to be true at this price point. Another website states 75db Signal to noise ratio. Is the specification an error?
greg  May 18, 2015
1 answer
A
I forwarded your question to an Advisor and they responded with the following: That spec is from the owner's manual (customer can download that from the product page under the details tab). They do indeed list the SNR as 95db. If you would like to discuss further you can contact an Advisor directly by phone (1-800-324-9695) or online chat.
kristina  May 20, 2015 (Staff)

Loading articles...

Compare the sound