About the Kicker CK8
This kit delivers all the power and signal your system needs
Your amplifier needs hefty power and ground wiring in order to deliver the big power you want. Kicker's CK8 amp wiring kit includes the power, ground, turn-on, and signal wiring for any amplifier with a fuse rating of up to 60 amperes. This kit is suitable for an amplifier with a maximum output of about 400 watts RMS for a Class AB amp or about 600 watts RMS for a Class D amp.
Includes patch cable and speaker wire
The CK8 kit includes a 17-foot, 2-channel twisted pair patch cable that'll send the signal reliably from the receiver to your amp with minimal noise. Also, Kicker provides 40 feet of 16-gauge speaker wire, enough to take care of both the front and rear speakers in most installations. Kicker makes all their wires from oxygen-free copper so you can count on maximum power and signal transfer with minimum resistance or interference.
Product highlights:
- amplifier wiring kit
- cables meet or exceed the American Wire Gauge specifications and requirements
- 17 feet of 8-gauge power cable with attached ring terminal and protective wire loom blue
- 2 feet of 8-gauge ground cable with attached ring terminal gray
- 17 feet of 16-gauge turn-on lead wire clear
- one 2-channel 17-foot twisted pair RCA patch cable
- 40 feet of 16-gauge speaker wire
- AFS fuse holder and 60-amp fuse
- assortment of installation hardware and cable ties
- extends your Kicker amplifier's warranty by one year, if purchased along with the amp
- warranty: 1 year
- MFR # CK8
What's in the box:
- 17' Length of 8-gauge power wire terminated with a 5/16" ring-terminal on one end (blue/black jacket)
- 2' Length of 8-gauge ground wire terminated with a 5/16" ring-terminal on one end (dark gray jacket)
- 17' Length of 16-gauge remote turn-on wire (clear jacket)
- AFS fuse holder
- 60 amp AFS fuse (installed)
- 17' Stereo RCA patch cord
- 40' Length of 16-gauge speaker wire
- One 7/8" Self-tapping screw (ground)
- 1 Flat washer
- 1 Plastic grommet
- 1 Red butt-connector
- Six 5" wire ties
- Four 3/16" crimp-on spade-connectors
- 2 Blue spade-connector sleeves
- 2 Black spade-connector sleeves
Scratch & Dent items may be missing non-essential accessories. In some cases the manufacturer's accessories have been replaced with generic equivalents.
See the difference between "Open Box" and "Scratch & Dent" Outlet items
Featured video:
Customer reviews for Kicker CK8
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kicker CK8
Product Research
Features
Single Amplifier 8-AWG Kit: This kit includes the following:
- One 17' length of 8-gauge power wire (terminated by a 1/2" wide, 5/16" diameter ring-terminal)
- One 2' length of 8-gauge ground wire (terminated by a 1/2" wide, 5/16" diameter ring-terminal)
- One 17' length of 16-gauge remote turn-on lead
- 17' Stereo RCA patch cord
- 40' Length of 16-gauge speaker wire
- AFS fuse holder
- 60A AFS fuse (installed)
- One 7/8" self-tapping ground screw with flat washer
- One plastic grommet
- Four 3/16" crimp-on spade-connectors (5/16" outer width)
- 2 Blue spade-connector sleeves
- 2 Black spade-connector sleeves
- Six 5" wire ties
- One red butt-connector
Hyper-Flex Power Cable: The power, ground, and speaker wires feature a Hyper-Flex jacket for easy installation. The RCA patch cord also has a Hyper-Flex jacket. Four feet of the power wire is covered with a wire loom to protect it in the engine compartment.
Silver Tinned OFC Copper: The power and ground cables are constructed of 735 strand silver tinned OFC copper. The speaker wire is 111 strand silver tinned OFC copper.
Fuse Holder: The fuse holder requires a 5mm Allen wrench to secure the input and output wires, and to change the fuse. There are four holes in the base for mounting and the dimensions are approximately:
- Width: 3-1/2"
- Height: 1-3/8"
- Depth: 1-5/8"
Loading...
Loading accessories...
Customer Q&A
3 questions already asked
Loading...
Loading articles...
Had everything I needed to hook up a mono amp to a sub box. Even ended with some unused scraps. High quality wires that look good if you can't cover them up and are easy to work with.
Willis from North Carolina