About the Brandmotion 9002-8847
The Wrangler-cam for factory radios
The Wrangler-cam for factory radios
Brandmotion's 9002-8847 rear-view camera integrates nicely into the rugged design of your Jeep Wrangler and displays everything it sees on the factory touchscreen radio if you have one. The camera's wide view and visibility for night driving make it a must-have for the hard-drivin' Wrangler owner. Use it for off-road reversing when you need to watch out for stumps and stuff, or install this cam with the optional parking lines activated if you're a town & country driver.
You'll hardly notice it
Brandmotion includes an adjustable bracket and camera head extension piece so you can mount the camera between the spokes of a wide variety of rear-mounted spare tires, including aftermarket tires. You'll also find the wiring harness needed for factory integration as well as a handy module that plugs into your Jeep's OBD-II port and reprograms the factory radio to be compatible with the camera.
Installing this camera yourself? Here's what you should know.
What does it do? Unless otherwise noted, a backup camera is only intended for use backing up your vehicle. (If you require a front-view or constant rear-view camera, check for that capability.)
What tools and supplies will I need? A panel tool, a wire cutter/stripper, a soldering iron, and a rosin-core solder with heat shrink tubing are recommended, along with whatever tools are needed to remove the radio from the dash.
How much wiring is required? Wiring instructions vary from camera to camera. Some cameras have power wiring that can only be connected near the radio. Others let you power the camera at compatible reverse lights. In all cases, the camera must be wired for power and ground, the camera's video output must be connected to the radio/monitor, and the radio/monitor must be connected to a reverse trigger in your vehicle. Some radio replacement interfaces supply a reverse trigger wire for the radio -- using that wire to power your camera will damage the interface.
Will the included video cable be long enough? You'll need to route the camera's video cable from its mounting location outside your vehicle into your vehicle's cabin and all the way to the screen in the dash. This often requires drilling a small hole in your vehicle or filing some metal and or plastic. You'll also need to estimate the length of cable needed to run from the camera to the dash, which will not be a straight shot. Each camera's cable length is listed.
Note: A rear-view camera provides an additional view when reversing your vehicle. It is intended to be used in conjuction with your rear- and side-view mirrors to give a fuller picture of what's behind you. It is not intended as a replacement for your mirrors.
Product highlights:
- CMOS rear-view camera
- includes adjustable bracket for fitting between varying spoke patterns of factory and aftermarket rear spare tire
- wide-angle camera compatible with select Jeep Wrangler factory touchscreen radios
- vehicle-specific harnesses and OBD-II program module included
- parking lines and mirror image (selectable at time of installation)
- 648 x 488 lines of resolution
- 170° wide viewing angle
- 0.5 Lux minimum for night driving
- warranty: 3 years
- MFR # 9002-8847
What's in the box:
Brandmotion 9002-8847 owner's manual
- Rear-view camera (with attached 2' cable)
- 20' Extension cable (pre-installed)
- Spare tire mounting bracket (pre-installed to camera)
- Short extension bracket (pre-installed to camera)
- Long extension bracket
- 18" Vehicle harness
- Program module
- 3 Push-nuts
- 15 Wire-ties
- Installation Instructions
Featured video:
Customer reviews for Brandmotion 9002-8847
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Brandmotion 9002-8847
Product Research
Features
Jeep Wrangler Camera Kit: The BrandMotion Jeep Wrangler Camera Kit (9002-8847) allows you to add a rearview camera to select Jeep Wranglers JK (including Unlimited version) with a factory radio display screen. The camera kit includes a rearview camera, spare tire mounting bracket, wiring harness, and hardware.
Vehicle Compatibility: The BrandMotion Jeep Wrangler Camera Kit (9002-8847) is designed specifically for 2007-2018 Jeep Wrangler JK (including Unlimited version) that feature a factory radio display screen. The rearview camera kit includes an OBD-II programming module for the factory radio, eliminating the need for dealer programming. Your Jeep Wrangler can have a rear-mounted factory or aftermarket spare tire wheel.
CMOS Backup Camera: The BrandMotion Jeep Wrangler Camera Kit features a CMOS backup camera that delivers 648 x 488 lines of resolution with a 170° wide viewing angle. The CMOS camera has a low-light lux rating of 0.5 for driving at night.
Park Assist Lines: The backup camera provides parking assist lines on the screen of your vehicle's factory radio display monitor. These parking lines are there to assist you when backing up into a parking space. There are two vertical lines which help you judge the left and right edges of the parking space and your vehicle. There are also 4 color-coded horizontal lines that are used to distinguish how close you are getting to the end of the parking spot - Green (Clear), Orange (Getting Close), Yellow (Very Close), and Red (Stop).
Spare Tire Mounting Bracket: The BrandMotion Jeep Wrangler Camera Kit comes with a spare tire mounting bracket to mount the rearview camera inside your spare tire on back of your Jeep Wrangler. The adjustable neck of the spare tire mounting bracket allows you to swivel the neck up, down, left, and right to fit the camera head between the different spoke patterns on varying wheels. Also, included in the kit are two camera head extension brackets (short & long) to work with varying wheel depths. The spare tire mounting bracket is designed to work with both factory and aftermarket wheels for the Jeep Wrangler.
Loading...
Loading accessories...
Customer Q&A
6 questions already asked
Loading...
Loading articles...
Perfect add on to the OEM head unit. Super easy to do. I wish the wiring plug was smaller so you could route it through the factory nylon loom on the rear gate for a more clean look
Dwight from MOUNTAIN CITY, GA