About the MTX TD500.1D
Upgrade your power for better sound
Upgrade your power for better sound
You'll add a big upgrade to your low-frequency listening pleasure when you put an MTX TD500.1D mono amp in your car. This compact amp will fit almost anywhere, driving your subwoofer setup with up to 500 watts RMS. Hook this amp up to a nice set of subs, and you'll hear sounds you've never heard before, even in your favorite songs. And this little bruiser will fit in places where amps don't usually go.
Advanced tone control
You can adjust the low-pass filter and subsonic filter to get the best possible sound from your sub and enclosure. In the unlikely event you want to bump up the bass a little, you also have access to a selectable bass boost.
Confused about impedance? Check out our article on matching subs and amps.
Product highlights:
- mono subwoofer amplifier
- 300 watts RMS x 1 at 4 ohms (500 watts RMS x 1 at 2 ohms)
- variable low-pass filter (40-220 Hz, 12 dB/octave)
- selectable bass boost (0, 6, 12 dB at 50 Hz)
- variable subsonic filter (10-50 Hz, 12 dB/octave)
- Class-D amplifier design
- frequency response: 10-220 Hz
- preamp inputs
- 4-gauge power and ground leads and a 60-amp fuse recommended wiring and hardware not included with amplifier
- no onboard fuses when installing multiple amps in a system, an additional 60-amp in-line fuse between the distribution block and the amplifier is recommended
- 9-1/2"W x 2-3/16"H x 5-9/16"D
- warranty: 1 year
- MFR # TD500.1D
What's in the box:
- Mono subwoofer amplifier
- Four 1/2" Self-tapping screws
- Owner's manual (English/ Spanish/ Portuguese/ French)
- Fuse and wiring kit note
Customer reviews for MTX TD500.1D
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the MTX TD500.1D
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
300 x 1 | |
Peak Power Output (Watts x Channels) | 1000 x 1 | |
Power at 2 Ohms (Watts x Channels) | 500 x 1 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-220 Hz | |
THD at Rated RMS Power | --- | |
Signal to Noise Ratio | 80 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 40-220 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0, 6, 12 dB | |
Bass Boost Frequency | 50 Hz | |
Fan Cooled | No | |
Fuse Rating | 60 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 9-1/2 | |
Height (inches) | 2-3/16 | |
Depth (inches) | 5-9/16 | |
Parts Warranty | 5 Years (3-5 Prorated) | |
Labor Warranty | 5 Years (3-5 Prorated) |
Product Research
Features
Mono Amplifier: The MTX TD500.1D is designed with specific features to power your subwoofer or subwoofers with a frequency range between 20 to 220 Hz. This amplifier is not designed to power a full-range speaker.
THD: The Total Harmonic Distortion isn't given at the rated power output, therefore it isn't listed in the specifications table. The manual does list THD as <0.3% at 30% of rated power (90 watts) into a 4-ohm load.
Protection Circuits: The TD500.1D provides protection against over heating, output short-circuit, and over/under power supply voltage.
Gain: The rotary gain control is continuously variable from 200 mV to 5 V.
Bass Boost: A three position switch adjusts the amplifier's bass boost; set to 0, +6 dB, or +12 dB. The boost is centered at 50 Hz.
Low Pass Crossover: The TD500.1D features a 12 dB/octave low pass crossover, continuously variable from 40 to 220 Hz. The crossover is always engaged (it cannot be bypassed).
Sub-Sonic Filter: The amp features a 12dB/octave sub-sonic filter, adjustable from 10 to 50 Hz. Ultra-low frequencies that cannot be reproduced by the subwoofer do not become sound but unnecessary oscillations, which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to the speakers. The sub-sonic filter removes the frequencies below the frequency setting to improve the performance of the speakers by eliminating harmful distortion.
Power/Ground/Turn-On: The TD500.1D features screw terminals for power, ground and remote turn-on. The power and ground terminals will accommodate spade connectors up to 0.5" wide, while the Remote turn-on terminal will accept a spade connector up to 0.335" wide.
Warranty Note: MTX will add a year to the standard one year warranty (for a total of two years) when an appropriate StreetWires amplifier wiring kit is used with this amp (4 gauge minimum). In this case, the StreetWires kits include a 150 amp fuse, which should be replaced with a 60 amp fuse (item number 211FAFS60, sold separately) to match the requirements for this amp. Both the amp and wiring kit should be purchased on the same order and the usual warranty limitations apply (covers manufacturing defects, must be purchased from an authorized MTX dealer, etc.).
Line Level Input: The signal is input using the stereo RCA inputs.
Speaker Connections: The amplifier is equipped with two pair of speaker terminals, internally shorted together, making it easy to connect two subwoofers. They are screw terminals and will accommodate spade connectors up to 0.335" wide.
EBC: There is a 3.5mm EBC (External Bass Control) jack on the amp, but as of 4/22/12 a compatible wired remote has not been released.
Warranty
5 Year Warranty Terms: This product carries a 5-Year Prorated Warranty with the following terms:
- Years 1-2: Products found to be defective in materials or workmanship during the first two years will be, at Mitek's option, repaired or replaced by Mitek at no charge. The warranty period does not renew, but continues on from the original date of purchase.
- Years 3-5: The purchase price of an item which becomes defective after the first two years and prior to the end of the warranty period will be prorated and credited toward the purchase of a new MTX product. The amount of proration is determined by dividing the original purchase price by the number of months in the warranty period (60), then multiplying the result by the number of months remaining in the warranty period.
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Picked this amp up to power my one 12 Thunder 8000 and it sounds nice. The size kf the amp is also plus for the power it packs u can pretty much fit it anywhere!
Damon from Alamogordo, NM