About the Alpine MRX-F35
Digital technology that sounds perfect
Digital technology that sounds perfect
Alpine's X-Power MRX-F35 4-channel amplifier uses the latest in amp technology to play your music loud and clean without taking up much space. And this compact amp employs some of the same circuitry developed for Alpine's top-of-the-line PDX digital amps so it'll bring exceptional sound to your ride.
Big power for clear sound
The MRX-F35 puts out 55 watts RMS per channel, so you'll have plenty of clean power to fill your listening space with music. You can even use it in 2-channel mode to drive a pair of subs with 170 watts each. Onboard frequency filters let you tailor the output to fit your setup, and a bass boost on the rear channels helps to fatten up the sound.
Alpine reliability
A power management system optimizes the amp's performance and keeps the music playing, even when you're pushing it hot and hard for a long time. Speaker-level inputs with an automatic turn-on feature simplify system hook-up.
Product highlights:
- 4-channel car amplifier
- 55 watts RMS x 4 at 4 ohms (85 watts RMS x 4 at 2 ohms)
- 170 watts RMS x 2 in bridged mode (4-ohm stable in bridged mode)
- CEA-2006 compliant
- variable high- and low-pass filters (50-400 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 50 Hz) on rear channels
- preamp and speaker-level inputs
- Class-D amplifier design
- MOSFET power and output stages
- fuse rating: 25A x 2
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 9-15/16"W x 2-5/16"H x 9-1/16"D
- warranty: 1 year
- MFR # MRX-F35
What's in the box:
- 4-Channel amplifier with two 25A ATO fuses installed
- Left plastic terminal cover
- Right plastic terminal cover
- 4 Terminal cover screws (M3 x 10mm)
- 4 Self-tapping screws (M4 x 20mm)
- 2.5mm Allen wrench
- 7" Speaker-level input harness
- Owner's Manual (Eng/ Fren/ Span)
- Warranty sheet
- Online registration card
- Alpine Verification Certificate
Customer reviews for Alpine MRX-F35
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Alpine MRX-F35
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
55 x 4 | |
Peak Power Output (Watts x Channels) | --- | |
Power at 2 Ohms (Watts x Channels) | 85 x 4 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 170 x 2 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 5-45k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 87 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-400 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | 50-400 Hz | |
High-Pass Slope (dB/octave) | 12 dB/oct | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 50 Hz | |
Fan Cooled | No | |
Fuse Rating | 50 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 9-15/16 | |
Height (inches) | 2-5/16 | |
Depth (inches) | 9-1/16 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Controls
Connections
Features
MRX Amplifier Design: Class-D amplifiers boast higher efficiency, produce less heat, and draw less current than traditional Class-AB amps. The MRX series benefits from the technology trickledown from Alpine's more expensive PDX amps, including Direct FET final outputs, thermal management processor, 6-Layer Glass Epoxy PC Board; combining to create a high-end sound quality without the bulky heat sinks required by most amps in this power class.
STAR Topology: Alpine's unique STAR (Signal Transit for Accurate Response) Circuit PCB design provides a single common ground for all amp sub-blocks, preventing ground interference and minimizing internal noise.
Power Management Processor: The multi-stage Power Management Processor continuously monitors component temperatures throughout the amplifier and decreases power output if anything gets too hot. When playing music under heavy loads for long periods, the circuit automatically reduces power output slightly at first, and then further in a second stage if necessary. This two stage approach provides an interruption free listening experience.
CEA 2006 Compliant: The MRX-F35's power ratings are measured according to the Consumer Electronics Association CEA-2006 standards. These standards allow you to accurately compare the rated power output of all CEA 2006-compliant amplifiers, even different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging. The power output is measured from 20 Hz to 20 kHz using a 14.4 volt power supply with no more than 0.01% THD+N:
- 4-ohms: 55 watts RMS x 4
- 2-ohms: 85 watts RMS x 4
- 4-ohm bridged: 170 watts RMS x 2
Signal-to-Noise: When measured under CEA-2006 conditions (reference 1 watt into a 4-ohm load) the signal to noise ratio is 87 dBA. Measured at the rated power output S/N is 104 dB.
Verification Certificate: The amplifier comes with a certificate that lists the RMS power output measured from that specific amplifier. It also lists the model number, serial number, test date, and the test conditions (voltage and impedance).
Auto Turn On: When using the speaker level inputs the X-Power amplifiers automatically turn on when voltage is detected on the signal inputs, making them an easy factory system upgrade.
Low Output Impedance: With low output impedance, the MRX-F35 outputs tightly controlled bass, with a damping Factor rated at greater than 500.
LED: The top panel LED power indicator glows blue when the amplifier is turned on.
Controls
Gain: The MRX-F35's gain can be independently set for the front and rear channels. The line-level input gain setting is continuously variable from 200 mV to 4.0V; the speaker-level input gain setting is continuously variable from 500 mV to 10.0V.
Crossovers: The amplifier has independent built-in crossovers for the front and rear channels. They can be set to low-pass or high-pass operation, or off via a three-way switch. The crossover frequency is continuously variable from 50 to 400 Hz and the slope is 12 dB/oct.
Bass EQ: Bass boost for the rear channels is variable from 0 to +12 dB and centered at 50 Hz.
Connections
Power/Ground/Remote: The MRX-F35 features set-screw terminals for the Power, Ground and Remote Turn-on inputs. The Power and Ground terminals will accommodate up to 4 gauge wire, while the Remote Turn-on terminal will accept up to 8 gauge wire. Based on the fuse rating and power output, 8 gauge power and ground wires are recommended.
Speaker Output: The speaker output terminals are screw terminals which will accept up to 8 gauge wire.
Line Inputs: Line level RCA is the preferred input connection. There are two pairs of RCA line-level inputs. No line output is provided.
Speaker Level Input: Use the included speaker level input harnesses if the connected radio has no preamp outputs.
Fuses: The amp is protected by two chassis-mounted 25-amp ATO fuses.
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...
I bought this amp to finally give some power to my Polk MOMO 5-1/4 components and this amp did not disappoint. Highs are clear and on point, midrange sounds fantasic with the extra power. Definitely worth the money. Alpine rated mine at 62 W.
Brent A from Pennsylvania