About the Alpine PDR-F50
Concentrated power
Concentrated power
Alpine managed to pack more power per square inch into their PDR-F50 4-channel Power Density Reference amplifier than almost any other amp in its class. The PDR-F50 can put out 85 watts RMS per channel, giving extra clarity and volume to your full-range speakers, and it'll fit in almost any of the tiny spaces you find in many cars and trucks these days. You can also use this versatile amp in 3-channel mode, driving your speakers with the front channels, and bridging the rear channels to send up to 250 watts RMS to your sub.
Tone control
Alpine included the tone controls you'll need to fine-tune your system so your speakers sound their best. You can use the high-pass filters to remove the extreme low bass from your full-range speakers, so they'll play more efficiently. If you plan on running subwoofers with your PDR-F50, you can adjust the low-pass filters and bass boost to get just the right bass tone.
Superior sound and build quality
Alpine built the PDR-F50 to exacting physical and electronic standards, resulting in a tough, powerful amp with an incredibly clean and noise-free output. All the electrical connections are made on one side, for more convenient and neat installations. Speaker-level inputs allow you to use this amp in almost any system, even one with a factory radio. And you can rotate the badge, so the Alpine logo can always display right side up no matter which way you mount your PDR-F50.
PDR-F50 control panel exposed
Product highlights:
- 4-channel car amplifier
- 85 watts RMS x 4 at 4 ohms (125 watts RMS x 4 at 2 ohms)
- 250 watts RMS x 2 in bridged mode (4-ohm stable in bridged mode)
- CEA-2006 compliant
- separate variable high- and low-pass filters (50-400 Hz, 12 dB/octave) on front and rear channels
- selectable bass boost (0, 6, or 12 dB at 50 Hz) on rear channels
- preamp and speaker-level inputs
- speaker-level inputs require RCA adapter cables
- Class-D amplifier design
- MOSFET power and output stages
- fuse rating: 30A x 2
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 9"W x 2-1/16"H x 7-1/8"D
- warranty: 1 year
- MFR # PDR-F50
What's in the box:
- 4-Channel class-D amplifier
- Two 30-amp ATO fuses (installed)
- Four 3/4" Self-tapping screws
- 3mm Allen wrench
- 2mm Allen wrench
- Alpine logo plate
- Owner's manual (English/ French/ Spanish)
- Verification certificate
- Warranty information
- On-line registration information
See the difference between "Open Box" and "Scratch & Dent" Outlet items
Customer reviews for Alpine PDR-F50
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Alpine PDR-F50
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
85 x 4 | |
Peak Power Output (Watts x Channels) | N/A | |
Power at 2 Ohms (Watts x Channels) | 125 x 4 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 250 x 2 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 8-45k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 87 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-400 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/octave | |
High-Pass Crossover Frequency | 50-400 Hz | |
High-Pass Slope (dB/octave) | 12 dB/octave | |
Bass Boost | 0, 6, 12 dB | |
Bass Boost Frequency | 50 Hz | |
Fan Cooled | No | |
Fuse Rating | 60 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 9 | |
Height (inches) | 2-1/16 | |
Depth (inches) | 7-1/8 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Controls
Connections
Features
Channel Design: The Alpine PDR-F50 can be configured as a 4-channel, 3-channel, or 2-channel amplifier. The amplifier is stable to 2-ohms in stereo, 4-ohms when bridged.
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). Using CEA-2006 criteria, the Alpine PDR-F50 is rated at 85 watts RMS x 4 channels with an 87 dBA signal to noise ratio. The signal to noise ratio at the rated power output (not CEA-2006 conditions) is 106 dB.
LED: The top mounted LED Power indicator glows blue when the amplifier is turned on and changes to red when the protection circuit is engaged.
Auto Turn-on: When using a speaker level input, the amp will turn on automatically when it senses the input signal.
Verification Certificate: The amplifier comes with a certificate that lists the RMS power output of the specific amplifier. It also lists the model number, serial number, test date, and the test conditions (14.4 volts, 2 ohms).
Controls
Hidden Controls: The amplifier's controls are hidden under a cover plate. The plate is removed by unscrewing two machine screws with the supplied 2mm Allen wrench.
Gain control: There are independent rotary gain controls for the channel-1/2 and channel-3/4 amplifier sections. The gain settings are continuously variable from 0.2 to 4.0 volts.
Crossover: The amp has independent crossover mode and frequency controls for channels-1/2 and 3/4:
- Mode: choose off (crossover is bypassed), high pass, or low pass
- Frequency: rotary dial; 50-400 Hz
Input: The two position input switch configures the inputs:
- 1/2: only inputs 1/2 are used, and are shorted to channels 3/4
- 3/4: all four RCA inputs are used
Bass Boost: The bass boost circuit provides +6 dB or +12 dB signal boost centered at 50 Hz to channels-3/4. The bass boost can also be turned off.
Connections
Terminal Layout: For wiring convenience, all of the inputs and outputs on the amplifier are on one side.
Power Input: Two set-screw terminals are provided for connecting the power and ground cables. The terminals accept up to 4-gauge wire (a 4-gauge wiring kit is recommended). The set screws are tightened/loosened with the included 3mm Allen wrench.
Remote Turn-on: The remote turn-on set screw terminal will accept up to 12-gauge wire. The set screw is tightened/loosened with the included 2mm Allen wrench.
Speaker Outputs: The four pair of speaker outputs set-screw terminals will accept up to 12-gauge wire. The set screws are tightened/loosened with the included 2mm Allen wrench.
Signal Input: The Alpine PDR-F50 is equipped with two pair of female RCA jack inputs; Channel-1/2 and Channel-3/4. The RCA inputs will accept either speaker-level or line level signals from your car's head unit. A speaker level signal is connected to the RCA inputs using a speaker wire to RCA adapter (sold separately).
Fuses: The amp is protected with two 30-amp ATO fuses.
The Alpine PDR-F50 replaces these items
Alpine MRX-F35
- 170 watts RMS x 2 bridged
- Class-D design
- preamp and speaker-level inputs
Loading...
Loading accessories...
Customer Q&A
3 questions already asked
Loading...
Loading articles...
Awesome Amp! Powers Up My 3 Sets Of Speakers And When Played Loud There's No Distortion Or That Sort Of Thing. The Amp Doesn't Get As Hot As Most Amps Would. Which Means It'll Last Longer.
Orange Street Boy from Makaha Valley, Hawaii