At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere.
That's because we have our own in-house Product Research team — they open the box,
verify contents, check the owner's manual, and record dimensions, features and specs.
We stay on top of new products and technologies to help people make informed choices.
Features
Controls
Connections
Features
PDX
Amplifier Design: Class-D amplifiers boast
higher efficiency, produce much less heat, and draw less current than
traditional Class-AB amps. The PDX series is Alpine's totally new
super-efficient power density design of full range class-D amps. They combine
MOSFET power supplies, MOSFET final outputs, and a
thermal management processor, along with a 4-Layer Glass Epoxy PC Board to
create a high-end sound quality without the bulky heat sinks required by most
amps with this much power.
STAR Topology:
Alpine's unique STAR (Signal Transit for Accurate Response) Circuit PCB design
provides a single common ground for all amp sub-blocks, preventing ground
interference and minimizing internal noise.
Terminal Layout:
For wiring convenience all the inputs and outputs on the amp are on one
side.
Verification Certificate:
The amplifier comes with a certificate that lists the RMS
power output of the individual amplifier. It also lists the model number, serial
number, test date, and the test conditions (14.4 volts, 4 ohms).
Speaker Connecters:
The PDX series amps use a new Speaker Quick Connect plug to attach the speaker
wires to the amp. Bare speaker wire, up to 8 gauge, is held in place by a set
screw, the Quick Connect plug then plugs into the amp. Like an RCA jack, the
Quick Connect plug uses a center positive layout, so it fits two ways and both
maintain correct polarity.
Stack Amps: Because the PDX series design
generates so little heat, up to three amps can be stacked and bolted together.
All three amps in the series, PDX-2.150, PDX-4.150, and PDX-1.1000 share the
same footprint, so they can be stacked together.
Notes: When stacking multiple amplifiers, do not install vertically or at an incline. Any stack installation other than parallel to the
vehicle floor, invalidates the warranty.
LED:
The top mounted LED Power/Status indicator glows blue when operating
normally and red when one of the protection circuits engages.
Protection Circuits: This
amplifier includes protection circuits to prevent damage due to the following
conditions:
- ambient temperature too high
-
supply current too high
-
short to ground
-
over voltage
Controls
Controls (front of unit):
Once set, the controls are covered by a door.
- Crossover Mode switch: set to HP (high pass),
OFF (full range) or
LP (low-pass), separate controls for the front and rear channels
- Crossover Frequency:
rotary controls used to select the crossover frequency, separate controls
for the front and rear channels, variable from 30 to
400Hz
- Gain control: rotary
controls used to set the amplifier's gain according the level of the incoming
signal, separate controls for the front and rear channels, continuously variable from 0.2V to 4.0V
- Input switch:
set to 1+3/2+4 (input 1 and 3 summed to feed channel 3, inputs 2 and 4
summed to feed channel 4, this makes channels 3 and 4 non-fading), 3/4
(channels 3 and 4 fed by inputs 3 and 4, maintains fader when head unit has
front and rear line outputs), or 1/2 (channels 3 and 4 fed by inputs 1 and
2, no Y-adapters needed when head unit has only one pair of line outputs)
Connections
Inputs and Outputs (rear of
unit):
- Power and Ground terminals: power and ground terminals are
gold plated set screw terminals, will accept up to 4 gauge bare wire, Alpine
recommends 6 gauge wire minimum
- Remote Turn-on terminal:
gold plated set screw terminal, will accept up to 10 gauge bare wire
-
Speaker terminals: each
of the 4 speaker outputs uses Alpine's Speaker Quick Connect plug
-
Line Level Input: 4 female RCA jacks, left and right
for the front and rear channels, gold plated
