1.888.955.6000
 
 
1-888-955-6000
crutchfield.com
Crutchfield

Rockford Fosgate Power T600-2

2-channel car amplifier
200 watts RMS x 2 (New Stock)

Zoom
  • Rockford Fosgate Power T600-2

    Front

  • Rockford Fosgate Power T600-2

    Side

  • Rockford Fosgate Power T600-2

    Top

Crutchfield OMC logo
We don't check this item for fit or compatibility.
 

Our take on the Rockford Fosgate Power T600-2

by Buck Pomerantz
Rockford Fosgate

My system has plenty of power. Who needs an amp?

You might think you don't need an amp because you have a 400-watt system in your car, or because your new stereo puts out 50 watts a channel. But those are peak wattage ratings, which may boil down to 15 or 20 watts per channel, using the more realistic RMS rating. An amp sends your speakers the power they need to deliver your music with clarity and impact, whether you're using factory speakers or high-performance components. And low-frequency reproduction requires lots of power, so an amp is an absolute must if you're adding a sub to your system.

Rockford Fosgate's Power Series Amplifiers

Rockford Fosgate has a well-deserved reputation for building high-quality mobile audio products. Their Power Series amps occupy the top of the amplifier food chain, with fine-tuned audio controls, extreme durability, and proprietary technologies that deliver stronger, more reliable performance than most other amplifiers on the market today.

High-grade internal components mean high-power output.

Even heat dispersal for longer life

Dynamic Thermal Management

Power Series amps use Rockford Fosgate's patented, award-winning "Dynamic Thermal Management," a 3-stage cooling system that uses forced air to dissipate heat evenly across the amp and out through the large heatsinks. This results in cooler internal components, higher efficiency, and lower distortion.

MEHSA cooling process

Maximum Efficiency Heat Sink Application increases heat transfer away from the transistors MEHSA is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. This allows the heat to escape more readily from the amplifier, so that the transistors stay cooler.


Extra-quiet inputs

Differential Inputs prevent noise from entering "Differential Input" circuitry helps eliminate any electronically induced noise or hum that could be picked up by the input cables, allowing only clean signals to enter the amplifier. You get more music with less heat and noise in a stylish package that's up to 40% smaller than previous models.


T600-2 Power performance

The T600-2 puts out 200 watts RMS into each channel — more than enough to drive a pair of full-range speakers or components to their musical peaks. Or you can bridge your T600-2 to blast 600 watts to a subwoofer or two. Either way, you will get clean, powerful sound from your Power Series amp. The Punch EQ circuit offers variable treble and bass boosts, so you can adjust your music for your car's listening environment.

T600-2 connections

Highlights:

  • 2-channel car amplifier
  • 200 watts RMS x 2 at 4 ohms (300 watts RMS x 2 at 2 ohms)
  • 600 watts RMS x 1 bridged output at 4 ohms (2-ohm stable in bridged mode)
  • CEA-2006 compliant
  • Dynamic Thermal Management cooling system
  • Differential Input circuitry eliminates hum
  • variable high- and low-pass filters (50-500 Hz, 24 dB/octave)
  • variable bass/treble boost (0-18 dB at 45 Hz, 0-12 dB at 12k Hz)
  • optional bass/treble boost
  • Class-AB amplifier design
  • MOSFET power and output stages
  • preamp inputs and outputs
  • 4-gauge power and ground leads and a 150-amp fuse recommended — wiring and hardware not included with amplifier
  • no on-board fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended
  • 13-11/16"W x 2-3/16"H x 9-5/8"D
  • warranty: 2 years
  • Our 60-day money-back guarantee
 

Hands-on research from the Crutchfield Labs (what are the Labs?)

Features and Specs
Performance
RMS Power Output (Watts x Channels)
Loading...
200 x 2
Peak Power Output (Watts x Channels)
Loading...
N/A
Power at 2 Ohms (Watts x Channels)
Loading...
300 x 2
Bridged Power (Watts x Channels)
Loading...
600 x 1
Minimum Impedance Bridged
Loading...
2
Minimum Impedance Unbridged
Loading...
1
Best Frequency Response
Loading...
20-20k Hz
THD at Rated RMS Power
Loading...
0.1%
Signal to Noise Ratio
Loading...
85 dB
Input Voltage
Loading...
14.4v
Features
Amplifier Class
Loading...
AB
Low-Pass Crossover Frequency
Loading...
50-500 Hz
Low-Pass Slope (dB/octave)
Loading...
24 dB/oct
High-Pass Crossover Frequency
Loading...
50-500 Hz
High-Pass Slope (dB/octave)
Loading...
24 dB/oct
Bass Boost
Loading...
0-18 dB
Bass Boost Frequency
Loading...
45 Hz
Fan Cooled
Loading...
No
Fuse Rating
Loading...
150
Speaker Level Inputs
Loading...
No
Preamp Outputs
Loading...
1 pair
Width (inches)
Loading...
13-11/16
Height (inches)
Loading...
2-1/4
Depth (inches)
Loading...
9-5/8
Parts Warranty
Loading...
2 Years
Labor Warranty
Loading...
2 Years
Product Research
What's in the box?

Download owner's manual

  • 2-channel amplifier
  • Four 1-1/2" Self-tapping screws
  • Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
  • Punch Amplifier Performance Verification Certificate
  • Optional PEQ remote EQ control information

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Features
Controls
Connections

Features

Cast Aluminum Heatsink: The cast aluminum heatsink dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs.

Dynamic Thermal Management (DTM): DTM Evenly distributes excess heat across entire amplifier heatsink.

MEHSA³ (Maximum Efficiency Heat Sink Application-Third Generation): MEHSA is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. The multi-layer insulated metal MEHSA substrate operates with minimal thermal resistance, spreading heat both downward and outward to quickly dissipate heat from each device across the heatsink. This allows greater power output, enhanced thermal stability, and maximum reliability.

Trans-ANA (TRANSconductance Active Nodal Amplifier): Trans-ANA is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed high voltage rails via a pair of drive transistors. Signal linearity is assured by an active node formed by the drive transistors at ultrasonic frequencies. The result is crystal clear sound quality.

NOMAD (NOn-Multiplying Advanced Decision): NOMAD is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed.

TO-247 MOSFET: The Power T400-2 utilizes ultra high performance MOSFET output devices, giving the amplifier more power handling capability as well as lower thermal impedance for more reliable operation, even under the harshest load conditions.

DSM (Discrete Surface Mount): In the manufacturing process high speed robotics are used to place 1% tolerance parts and large board traces. DSM improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature.

Power and Protection LEDs: The LEDs are located on top of the amplifier. A blue Power LED illuminates when the amplifier is turned on. A red Thermal LED illuminates if the amplifier overheats. The yellow Protect LED illuminates if a short circuit or too low an impedance is detected at the speaker connections. When any of the protection circuits engage, the amp automatically shuts down until the problem is corrected.

Controls

Internal Crossover: The amplifier's internal crossover has a 24 dB/octave slope. It's selectable for high-pass, all-pass (full range), or low-pass operation and is variable from 50Hz to 500Hz.

Punch EQ: Punch EQ works along with the crossover switch. When the crossover is set to low-pass, the Punch EQ acts as a variable bass boost; 0-18 dB at 45 Hz. When the crossover is set to high-pass, the Punch EQ acts as variable treble boost, 0-12 dB at 12 kHz. When the crossover is set to all-pass, both the bass and treble boost circuits are active.

Connections

Power Connections: The power and ground terminals are nickel-plated captive c-clamp wire connectors and will accommodate up to 4-gauge wire. An external 150-amp fuse (not included) must be installed on the power wire. The remote turn-on terminal will accept wire sizes of 12- to 24-gauge. A Phillips-head or slotted screwdriver (not supplied) is required to tighten/loosen the terminals.

Speaker Connections: The 2-channel nickel-plated clamp wire connectors will accept 8-gauge to 18-gauge wire. A Phillips-head or slotted screwdriver (not supplied) is required to tighten/loosen the terminals.

Remote Punch EQ (PEQ) Connection: An RJ-45 jack is provided for connecting an optional remote PEQ control (575ROCKPEQ, sold separately). If you use the remote PEQ, the Punch EQ control on the amp is disabled, and replaced by the remote. Note: Previous model Punch Bass and Para-Punch remotes will not work with this amp.

 
Review this product
Great Gear Giveaway rewards card

Submit a review and you will be entered to win a $150 gift card

Crutchfield Great Gear Giveaway Official Sweepstakes Rules

Rockford Fosgate Power T600-2 Reviews

Average Customer Review:

2 people say:

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left
Filter by rating:
5 out of 5

Excellent Sub Amp

Written By Daniel, Mobile, AL on Saturday, March 06, 2010
 
Replacing an equivalent Kicker amp to run two 10" L5 2 ohm DVC. Running each at 4ohm on separate channels. Runs louder, cleaner, and cooler than the kicker. Compact size makes it ideal below the rear seat of my Jeep Wrangler. Can't go wrong with Rockford.
7 out of 8 people found this helpful
Was this review helpful?    Yes | No
 
5 out of 5

Better bring some subs..

Written By jimmy v, NC on Thursday, June 18, 2009
 
I installed this hitting 2- 10" JL 10W3V3 in my 08 Silverado EXT CAB a few
days ago. This amp will make you deaf. I have it running at lower than half
gain, LP, about 100HZ and it absolutely destroys the subs. I am going easy
during the break in time, but I will see what it has soon. Typical RF it says
600 but sheet says 780X1 at 4 OHMS Bridged. I have had Punch for years,
never Power series, but I see the difference. Never go wrong with RF!
15 out of 17 people found this helpful
Was this review helpful?    Yes | No
 

Add accessories for the Rockford Fosgate Power T600-2

You'll need an amp wiring kit to install your new amplifier, as wiring is not included. See all categories & accessories

Rockford Fosgate RFK4 4-gauge amplifier power wiring kit
6 people say
Your Price: $114.99
Add to Cart
Rockford Fosgate RFK4X Complete 4-gauge amplifier wiring kit
Includes patch cable and speaker wire
9 people say
Your Price: $159.99
Add to Cart
EFX 4-gauge Amplifier Wiring Kit Power and signal connections for your new amp
70 people say
Your Price: $79.99
Add to Cart
T-Spec 16-gauge Speaker Wire Black/white jacket — priced per foot
9 people say
Your Price: $0.69
Add to Cart
T-Spec 12-gauge Speaker Wire Black/white jacket — priced per foot
17 people say
Your Price: $1.99
Add to Cart
Stinger PRO Series 16-gauge Speaker Wire Black jacket — priced per foot
37 people say
Your Price: $0.39
Add to Cart
T-Spec 2-Channel RCA Patch Cables Available in 7 different lengths (20-foot)
13 people say
Your Price: $20.99
Add to Cart
44 people say
Your Price: $9.99
Add to Cart
JL Audio XD-CLRAIC2-SW 2-channel speaker output converter (bare speaker wires to male RCAs)
11 people say
Your Price: $9.99
Add to Cart
Rockford Fosgate PEQ Amp Remote Control For 2007-up Power and Punch Series amps
22 people say
Your Price: $29.99
Add to Cart
StreetWires AFS Fuses 2-pack (6 sizes available) (150-amp)
3 people say
Your Price: $6.99
Add to Cart
T-SPEC V6-MANL Fuse Holder 4- to 8-gauge mini-ANL fuse holder
Your Price: $9.99
Add to Cart
EFX CAFH Fuse Holder In-line AGU fuse holder accepts 4/8-gauge wire
1 person says
Your Price: $12.99
Add to Cart
T-Spec Capacitor 1.5-farad capacitor with red LCD meter
3 people say
Your Price: $79.99
Add to Cart
S&G Wire Cutter/Stripper Tool Cuts and strips 12- to 22-gauge wire
12 people say
Your Price: $19.99
Add to Cart
S&G Tool Aid 87650 Door Trim and Panel Removal Tool
63 people say
Your Price: $9.99
Add to Cart
Pro.Fit Wire Worm Installation tool helps route wiring through tight spaces
25 people say
Your Price: $12.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
42 people say
Your Price: $24.99
Add to Cart
Skewdriver Pro SPK4042 Ratcheting straight and offset screwdriver set with 40 bits (Skewdriver Pro with ratchet handle, pictured)
7 people say
Your Price: $49.99
Add to Cart
Bojo Trim Panel Tools Set of 6 pry tools — helps remove interior and exterior trim and door panels
1 person says
Your Price: $29.99
Add to Cart
DEI Heat Shrink Tubing Black 4-foot length (Assortment)
4 people say
Your Price: $24.99
Add to Cart
InstallCard: Amp or Equalizer Prepaid professional amplifier or EQ installation
16 people say
Your Price: $79.99
Add to Cart
Your Price: $69.95
Add to Cart

Why choose SquareTrade?

The #1-Rated Protection Plan

Thousands of people have reviewed SquareTrade Protection Plans — and made us #1.

5-Day Service Guarantee & Free Shipping

We'll repair or replace your item in five business days or less after we've received it, or your plan is free. And, as always, we pay for all shipping.

Protection from Normal, Everyday Use

Repairing your average mechanical or electrical failure can cost as much as buying a new device. With SquareTrade, you're covered — including parts and labor.

3 Year Protection Plan
3 Year Protection Plan
Your Price: $69.99
Add to Cart

For a more in-depth review and enhanced detailed information on the Rockford Fosgate Power T600-2, please visit the Crutchfield website product page (/ISEO-rccbcspd/p_575T6002P/Rockford-Fosgate-Power-T600-2.html ).