Chat
Contact us
Close contact box
Connect ID #
792 497 897 4
Connect ID #
792 497 897 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Kenwood KAC-5206 2-channel car amplifier — 60 watts RMS x 2 (Factory Refurbished)

Item # 613KAC5206

Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance.

Find what Fits your vehicle

Remove

Checking fit...

Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance.

Item # 613KAC5206

Shop all Kenwood (Refurbished) Car Amplifiers

About the Kenwood KAC-5206

Bob Bihlmayer

Reliable performer

Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance. Add the Kenwood Sport Series KAC-5206 amplifier to your system, and you'll hear all the tonal color, impact, and detail you've been missing, from the punch of the rhythm section to the shiver induced by your favorite singer's voice.

Reliable performer

Kenwood makes tough, rugged amplifiers that bring you superior sound quality along with reliable performance. Add the Kenwood Sport Series KAC-5206 amplifier to your system, and you'll hear all the tonal color, impact, and detail you've been missing, from the punch of the rhythm section to the shiver induced by your favorite singer's voice.

Power your sub

The compact KAC-5206 2-channel amp delivers 60 watts RMS per channel to your full-range speakers. This amp will bring new life to factory speakers, but you'll really notice the difference when you pair it up with new aftermarket speakers or components.

READ LESS

Product highlights:

  • 2-channel car amplifier
  • 60 watts RMS x 2 at 4 ohms (75 watts x 2 at 2 ohms)
  • 150 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode)
  • CEA-2006 compliant
  • switchable low-pass filter (80 Hz at 18 dB per octave)
  • Class AB design and MOSFET power supply
  • preamp and speaker-level inputs
  • signal sensing turn-on eliminates need for remote lead
  • 10-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • fuse rating: 25A x 1
  • 9-1/8"W x 2-1/8"H x 7-1/8"D
  • warranty: 90 days
  • MFR # KAC-5206

What's in the box:

  • Refurbished 2-channel amplifier
  • 25 amp ATO fuse (installed)
  • 7" Speaker-level input harness
  • Four 5/8" Self-tapping screws
  • Instruction manual (English/ French/ Spanish)
  • Warranty information

Customer reviews for Kenwood KAC-5206

Loading reviews...

Average review:

4.5 out of 5 stars
7 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Customer provided image, click to load a larger version.
Customer provided image, click to load a larger version.

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee review (What's this?)

Reviewed on Samsung.com

This review was collected as part of a promotion

Pros:

Cons:

Crutchfield response
Customer provided image, click to load a larger version.
<< >>

Product Research

Features
Controls
Connections
Warranty Note

Features

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). Using CEA-2006 criteria, the Kenwood KAC-5206 is rated at 60 watts RMS x 2 channels with an 80 dBA signal to noise ratio. The signal to noise ratio at the rated power output (not CEA-2006 conditions) is 95 dB.

2-Ohm Stable: The amplifier can support a 2-ohm load in stereo; the 2-ohm power output is 75 watts RMS x 2 channels.

Bridgeable: This two-channel amplifier can be bridged to a 4-ohm mono load; the bridged output is 150 watts x 1 channel RMS.

Cast Aluminum Heat Sink: The KAC-5206 utilizes a cast aluminum heat sink design to ensure the amplifier stays cool.

Protection circuitry: The amplifier features protection circuits that will turn the amp off in case of the following events:

  • speaker wire short-circuits
  • speaker output contacts ground
  • unit malfunctions and DC is sent to speaker output
  • the amp overheats

Power Indicator: When the amplifier is turned on the Power indicator (on top of the amp) lights up. This indicator turns off with the amplifier, and will turn off if the amplifier goes into protect mode.

Auto Turn-on: When using a speaker level input, the amp will turn on automatically when it senses the input signal.

Controls

Gain: To accommodate the varying range of signal levels from today's factory and aftermarket radios, the KAC-5206 features an adjustable gain control; 0.2-5.0 volts line level (RCA) and 4.0-12.0 volts speaker level.

Low Pass Crossover: The amplifier has an 80Hz, -18dB/oct low-pass filter which can be turned On or Off.

Connections

Power Connections: The power, ground, and remote turn-on connections are 0.35" wide screw terminals. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended. Minimum 10 gauge wire is required for power and ground.

Speaker Outputs: The two pair of speaker outputs are 0.35" wide screw terminals. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are also recommended for the speaker wires.

Note: The speaker output terminals can be used in stereo or bridged mode.

Line Level Input: The line input is a pair of stereo RCA jacks.

Speaker Level Input: A wiring harness is included for the speaker level input.

Fuse: The amplifier uses a 25-amp ATO blade-type fuse.

Warranty Note

Warranty Note: This refurbished Kenwood product carries a 90-day warranty when purchased from Crutchfield. Kenwood offers Crutchfield customers an extra 60 days extended warranty beyond the 30-day Kenwood Limited Warranty for Refurbished Product that comes in the box.

Loading accessories...

Customer Q&A

Loading articles...

Compare the sound