Alpine Authorized Online Dealer

This Alpine package includes a 500-watt mono amp, two 12" subs, and a Sound Ordnance sealed dual 12" enclosure that will all combine for some heavy low-frequency reinforcement in your vehicle. Just add some wiring, and you've got a complete system that will transform your music on the road.

MRP-M500 mono sub amp
Alpine's V-Power MRP-M500 mono amplifier drives your two subwoofer system with 500 watts RMS, with the sound quality that made Alpine famous. The thermal management system dissipates heat and saves power, so this amp will run reliably for years to come. The low-pass filter puts you in command of the frequencies that reach your subs, while the variable bass boost is armed with plenty of low-end punch. A subsonic filter prevents wasted energy by eliminating ultra-low bass, putting all the power where you need it.

Two SWE-1243 12" subwoofers
The 4-ohm SWE-1243 12" subwoofer handles up to 250 watts RMS, so this pair of subs makes a perfect match for the MRP-M500 amp. Alpine treats the two-layer pulp cone with Kevlar so it won't buckle or distort under heavy use, while the tough Santoprene rubber surround keeps your cone under control for more accurate bass. Extra venting maximizes air flow through your speaker, dissipating heat and increasing your sub's reliability. The heavy-gauge, stamped steel cage holds its shape through the most relentless pounding, so your bass stays tight.

Sound Ordnance dual 12" sealed enclosure
Sound Ordnance's rugged Bass Bunker BB122-100S sealed enclosure holds two 12" subwoofers and offers an internal volume of 1.035 cubic feet per chamber. This unloaded enclosure features high-grade, medium-density fiberboard construction, with sealed inner braces that help combat resonance by reducing vibrations.

Important Note: The amplifier in this bass package is a good match for the included sub(s), but it's still important to set the amp's gain controls properly to avoid distortion. This diagram shows you how to wire up the sub(s) in this package.

Product Highlights:

  • package includes MRP-M500 amp, two SWE-1243 12" subs, and Sound Ordnance enclosure
MRP-M500 mono subwoofer amplifier
  • 300 watts RMS x 1 at 4 ohms (500 watts x 1 at 2 ohms)
  • variable low-pass filter (50-200 Hz, 24 dB/octave)
  • variable bass boost (0-12 dB at 50 Hz)
  • subsonic filter (15 Hz, 24 dB/octave)
  • speaker- and preamp-level inputs
  • fuse rating: 30A x 2
  • 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • 10-11/16"W x 2-7/16"H x 9-9/16"D
  • warranty: 1 year
SWE-1243 12" 4-ohm subwoofers (pair)
  • Kevlar®-treated pulp woofer cone with Santoprene rubber surround
  • power range: 100-250 watts RMS
  • frequency response: 27-1,000 Hz
  • sensitivity: 86 dB
  • warranty: 1 year
BB122-100S sealed enclosure
  • hatchback style enclosure for two 12" subwoofers
  • 5/8" MDF (medium-density fiberboard) with black carpet covering
  • dimensions: 27-5/8"W x 14-9/16"H x 13-1/2"D1 x 10-1/2"D2
  • warranty: 1 year
  • Our 60-day money-back guarantee

Hands-on research

What's in the box?

  • This Alpine Amp/Sub Package contains four individually packaged items: the MRP-M500 Amplifier/ two SWE-1243 12" Subwoofers/ and a Sound Ordnance subwoofer enclosure
  • The MRP-M500 Amplifier includes:
  • Mono amplifier
  • Two 30 amp fuses (installed)
  • 7" Speaker-level input harness (4-pin Molex plug on one end and bare wires on the other)
  • 2 Terminal covers
  • 4 Self-tapping hex-head screws (M4 x 20mm)
  • 4 Machine screws for securing terminal covers (M3 x 12mm)
  • Owner's manual (English/ French/ Spanish)
  • Customer care registration card
  • Each SWE-1243 Subwoofer includes:
  • One 12" subwoofer
  • Rubber concealing ring (installed)
  • Black plastic grille
  • Type-E Subwoofer application guide (English/ French)
  • Warranty card
  • Customer care registration card
  • Important Notice! note
  • Grille installation diagram
  • The subwoofer enclosure includes:
  • Dual hatchback-style enclosure for 12" subwoofers with spring-post terminals

Product Research

Amplifier Features
Amplifier Controls
Amplifier Connections
Subwoofer
Enclosure

Amplifier Features

Power Supply: The MRP-M500 amplifier's power supply uses MOSFETs to convert DC battery voltage to the higher DC voltages needed for high power. It supplies positive and negative voltages around 0V, rather than around 6V as with conventional single-polarity power supplies. The result is higher power levels and a dynamic range wider by as much as 10dB.

Inputs: The amplifier offers both line-level and speaker-level inputs for 2 channels. The supplied speaker-level input harness allows you to connect this amplifier to a receiver without preamp outputs; aftermarket or factory. The speaker level inputs will accept the output from a high powered radio.

Terminal Covers: The amp comes with two plastic covers that protect and insulate the RCA, power, and speaker connections. Four supplied machine screws attach the covers to the amplifier.

Amplifier Controls

Low Pass Filter: The amp is equipped with a 50-200Hz variable low-pass filter with a slope of 24dB/octave. This being a mono subwoofer amp, the crossover is always engaged.

Subsonic Filter: This amp utilizes a subsonic filter at 15Hz to eliminate super low frequencies that can rob power and damage speakers. The subsonic filter operates at all times, and cannot be turned off.

Bass EQ: The Bass EQ circuit provides a variable boost (0-12dB) at 50 Hz.

Amplifier Connections

Left Side Of Amplifier:

  • GND (ground): gold-plated screw terminal, 0.33" wide
  • Battery: gold-plated screw terminal, 0.33" wide
  • Remote: gold-plated screw terminal, 0.33" wide
  • Speaker Output: gold-plated screw terminal, 0.33" wide

Note: Alpine recommends 8 gauge power and ground wire (minimum).

Right Side Of Amplifier:

  • Line Inputs: 1 pair of gold-plated stereo RCA jacks
  • Speaker Level Input: Molex plug input for supplied 4-pin harness

Subwoofer

Woven Fiber/Kevlar Reinforced Pulp Cone: This Alpine Type-E subwoofer features a two-piece parabolic woven fiber and Kevlar reinforced pulp cone. Kevlar adds strength and tear resistance to the woofer cone while maintaining the benefits of a pulp cone design. The lightweight cotton fiber design provides a faster and more dynamic response from the woofer.

Santoprene Rubber Surround: The high-excursion, tapered half-roll, injection molded Santoprene rubber surround is durable and resistant to the elements, resulting in a very reliable performance. The surround is specially designed to resist deformation that is common in woofers with wide surrounds. This design gives the surround more control over the woofer cone to reduce distortion and possible driver failure.

Progressive Nomex Spiders: This subwoofer utilizes a Progressive Nomex spider for stability and mechanical durability. The custom progressive roll gives the woofer a longer, more linear stroke with maximum centering and restoring force. Special edge control design and Nomex construction provide excellent tear resistance, strength and long-term reliability.

Voice Coil: The Alpine SWE-1243 features a 4-layer single voice coil made from 180-degree high-temperature wire on an aluminum bobbin.

Airflow Optimized Extended/Vented Pole: This SWE-1243 features an extended pole piece which provides optimum airflow for the woofer.

Custom High Strength Steel Basket: The frame is custom stamped from high strength steel.

Speaker Terminals: This Alpine Type-E subwoofer features a pair of heavy duty push-terminals on one side of the woofer's basket that will accommodate up to 8-gauge speaker wire.

Tinsel Leads: The Type-E subwoofer uses insulated 16-gauge stranded tinsel leads.

Gasket Cover: Alpine uses a Concealed Mount Gasket System to cover the mounting screws for a clean look. The black rubber gasket ring comes already installed on the woofer and needs to be removed before drilling the mounting screws (not supplied). The gasket ring then snaps back into place once the woofer is mounted.

Protective Grille: The Alpine SWE-1243 Type-E subwoofer comes supplied with a high impact protective grille. The black plastic grille snaps onto the woofer without the need for any additional hardware. The rubber gasket cover must be removed when using the grille. The grill also hides the mounting screws, as well as protects the woofer. The grille adds 0.9425" to the woofer's height (1.6875").

Enclosure

Materials: The Sound Ordnance BB122-100S Bass Bunker is an unloaded, hatchback-style sealed enclosure for a dual 12" subwoofers. It is constructed of 5/8" MDF (medium-density fiberboard), covered in black carpet.

Internal Box Volume: The enclosure has two separate chambers, each with 1.035 cubic feet of airspace.

Terminals: The BB122-100S is equipped with two pairs of spring-post speaker terminals, one for each chamber, mounted in the rear panel. The spring terminals will accept bare wire, pin connectors, and single banana plugs, but are spaced too far apart for dual banana plugs. Inside the enclosure, each set of terminals has an attached 18" length of speaker wire for connecting the subwoofer.

Brackets: Brackets for securing the enclosure to your vehicle are recommended.

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Alpine 500-watt Dual 12" Bass Package Reviews

Average Customer Review:

1 reviews
Review this product
Great Gear Giveaway

Submit a review and then enter to win a $500 rewards card

(0)
(0)
(0)
(0)
(0)

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
  Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left

Alpine 500-watt Dual 12" Bass Package

Written By Jcote, NH on Thursday, October 13, 2011

This package is the real deal! i have used alpine speakers in cars before but never the subs, installed them in my 2001 jetta and it kicks HARD! hard enought that i have to leave it at about 75percent output on the amp and 25percent on my Deck for fear of my rear view mirror falling off the window. all in all very impressed for the cost performance ratio! A good buy!

Get everything you’ll need to enjoy your new Alpine 500-watt Dual 12" Bass Package

Kits make it easier and less expensive to install your new amplifier. Wiring not included with the amp.
It's critical to have good wire, and none is included with the subs.
Dynamat helps reduce ambient road noise and your vehicle's "rattles," making it easier for you to hear your music better. Easy to install.
Protect your charging system and improve your bass with a capacitor. Ground cable and connectors required (not included).
Don't forget those little extras that enhance your sub box.
These tools will make the installation easier.
Get more info about having your new amplifier put in by a qualified professional in your area.
Patch cables take the music from your stereo to the amplifier. Some kits don't include them, and you can always get better quality cables like these separately.
T-Spec 8PK Installation Kit

T-Spec 8PK Installation Kit

8-gauge amplifier wiring kit — includes speaker wire

Item #: 1208PK

(6)

$59.99
Add to Cart
Rockford Fosgate RFK8

Rockford Fosgate RFK8

8-gauge amplifier power wiring kit

Item #: 575RFK8

(6)

$64.99
Add to Cart
Rockford Fosgate RFK8i

Rockford Fosgate RFK8i

8-gauge amplifier power and signal wiring kit

Item #: 575RFK8I

(30)

$74.99
Add to Cart
Kicker PK8

Kicker PK8

8-gauge amplifier power wiring kit

Item #: 206PK8

(1)

$79.99
Add to Cart
EFX PA8BX Wiring Kit

EFX PA8BX Wiring Kit

8-gauge amplifier wiring kit — includes 2-channel patch cable

Item #: 142PA8BX

(5)

$49.99
Add to Cart
T-Spec 12-gauge Speaker Wire

T-Spec 12-gauge Speaker Wire

Black/white jacket — priced per foot

Item #: 120SW12WB1

(30)

T-Spec 16-gauge Speaker Wire

T-Spec 16-gauge Speaker Wire

Black/white jacket — priced per foot

Item #: 120SW16WB1

(13)

Dynamat Dynaliner

Dynamat Dynaliner

One 54" x 32" sheet (1/8" thick)

Item #: 15411101

(6)

$69.99
Add to Cart
Dynamat 19100

Dynamat 19100

License Frame Kit

Item #: 15419100

(15)

$14.99
Add to Cart
Dynamat Xtreme Wedge Pack

Dynamat Xtreme Wedge Pack

1 sheet, 4 square feet

Item #: 15410425

(7)

$39.99
Add to Cart
Dynamat Xtreme Trunk Kit

Dynamat Xtreme Trunk Kit

5 sheets, 20 square feet

Item #: 15419405

(13)

$169.99
Add to Cart
Dynamat SuperLite Tri-Pak

Dynamat SuperLite Tri-Pak

Triple package — 3 sheets, 12 square feet (Model #10612)

Item #: 15410612

(17)

$69.99
Add to Cart
T-Spec Capacitor

T-Spec Capacitor

1.5-farad capacitor with red LCD meter

Item #: 12015DDC

(11)

$79.99
Add to Cart
Box Brackets

Box Brackets

Item #: 125B702KIT

(5)

Polyester Fiber Stuffing

Polyester Fiber Stuffing

Make your subwoofer think it's in a bigger box (1-pound pack)

Item #: 027808

(35)

$12.99
Add to Cart
Metra Speaker Terminal

Metra Speaker Terminal

Round terminal cup with spring clip connectors (for do-it-yourself box builders)

Item #: 120TCRS

(6)

Metra Speaker Terminal

Metra Speaker Terminal

Square terminal cup with spring clip connectors (for do-it-yourself box builders)

Item #: 120TCSS

(7)

Metra Speaker Terminal

Metra Speaker Terminal

Square terminal cup with binding post connectors (for do-it-yourself box builders)

Item #: 120TCSB

(7)

Metra Speaker Terminal

Metra Speaker Terminal

Round terminal cup with binding post connectors (for do-it-yourself box builders)

Item #: 120TCRB

(13)

Corner Protectors

Corner Protectors

Item #: 1251536

(5)

Metra Box Carpet

Metra Box Carpet

Carpet roll (54" x 5 yards) — available in 3 colors (Silver)

Item #: 120TL3645

(24)

$39.99
Add to Cart
Metra Crimp Tool and Connectors

Metra Crimp Tool and Connectors

Package contains crimp tool and over 150 pieces

Item #: 120CRIMPKT

(15)

$19.99
Add to Cart
S&G Tool Aid 87650

S&G Tool Aid 87650

Door Trim and Panel Removal Tool

Item #: 18187650

(69)

S&G Wire Cutter/Stripper Tool

S&G Wire Cutter/Stripper Tool

Cuts and strips 12- to 22-gauge wire

Item #: 18119100

(15)

$19.99
Add to Cart
Pro.Fit Wire Worm

Pro.Fit Wire Worm

Installation tool helps route wiring through tight spaces

Item #: 042DM4533

(33)

$12.99
Add to Cart
Pro.Fit Trim Panel Tool

Pro.Fit Trim Panel Tool

Remove your vehicle's trim panels without damage

Item #: 042DM4022

(87)

Bojo Trim Panel Tools

Bojo Trim Panel Tools

Set of 6 pry tools — helps remove interior and exterior trim and door panels

Item #: 126CR6NGL

(52)

$24.99
Add to Cart
Skewdriver Pro SPK4042

Skewdriver Pro SPK4042

Ratcheting straight and offset screwdriver set with 40 bits (Skewdriver Pro with ratchet handle, pictured)

Item #: 180SPK4042

(8)

$49.99
Add to Cart
Bojo Trim Panel Tools

Bojo Trim Panel Tools

Set of 6 pry tools — helps remove interior and exterior trim and door panels

Item #: 126CR6LNGL

(2)

$29.99
Add to Cart
InstallCard: Amp or Equalizer

InstallCard: Amp or Equalizer

Prepaid professional amplifier or EQ installation

Item #: 597421003

(18)

$79.99
Add to Cart
T-Spec 2-Channel RCA Patch Cables

T-Spec 2-Channel RCA Patch Cables

Available in 7 different lengths (20-foot)

Item #: 120RCA202

(27)

$20.99
Add to Cart
EFX 17-foot RCA Patch Cable

EFX 17-foot RCA Patch Cable

Item #: 142A17C

(55)

$7.99
After $2.00 Savings Add to Cart