NAD Masters Series M2

Direct Digital stereo integrated amplifier

  • NAD Masters Series M2


  • NAD Masters Series M2

    Analog audio signal path

  • NAD Masters Series M2


  • NAD Masters Series M2


  • NAD Masters Series M2

    Direct Digital signal path

  • NAD Masters Series M2


  • NAD Masters Series M2

    Zetex DDFA chip


Our take on the NAD Masters Series M2

by Jim Richardson

Everything you always wanted in a stereo receiver, except the radio

An integrated amplifier is essentially a receiver without a built-in AM/FM tuner. You get power to drive your speakers, audio controls, and inputs for music source components. Connect an iPod, a computer, a network music player, or any other device that can play Internet radio, and you may find you have no need for an AM/FM radio.

A stunning breakthrough in digital amplifier design

The M2 Direct Digital Amplifier is the product of a decade-long NAD research project that was followed by three years of product development. Highly efficient, immensely powerful and musically involving, the M2 sets a new performance benchmark for digital amplification. It compares favorably with the world's best amplifiers, regardless of price or design philosophy.

"The M2 ... sounds remarkable, with tremendous dynamics, extremely low noise,
richly textured and defined bass, and three-dimensional soundstaging."
—Robert Harley, The Absolute Sound magazine, March 2010

Streamlined signal path dramatically reduces noise

analog signal path

Because the M2 handles digital audio signals directly, you won't hear the noise and distortion that's added by the analog amplifying stages found in traditional amplifiers. NAD says this streamlined signal path reduces overall system noise by a factor of three.

Without all that noise to compete with, the subtle details you never noticed emerge from music you've heard a hundred times. You perceive the dimensions of the performance space and the rich tonal texture of each instrument. What once sounded like a mere violin now reveals itself as a Stradivarius, and you savor each note as it blossoms and ripens before yielding to the next one.

Typical signal path through an analog system

The diagram at right shows the signal path of a traditional amplifier setup, which includes as many as 10 steps between the digital audio source and your speakers, including:

  • The digital-to-analog converter and its buffering circuitry. If it's a stand-alone converter, there will be a cable from there to the preamp.

  • The analog preamp and its buffering circuits. If it's a separate unit, then add one more cable to the signal path.

  • The analog power amplifier, which typically places three more stages of circuitry in front of the output stage.

M2 signal path

The diagram below shows the path the signal from a digital music source takes through the M2 on its way to your speakers. The only stop along the way is to decode the signal. You can think of the M2 as a DAC with a built-in amp. It's that simple, and that's why noise and distortion vanish.

M2 signal path

Read more

Groundbreaking Zetex chip cancels out distortion

Zetex DDFA chip

The Zetex DDFA™ (direct digital feedback amplifier) chip enables NAD's breakthrough in class D amplifier sound quality. Until now class D amplifiers had been used primarily in subwoofer amps, because their full-range sound could not compete with the sound of the best analog amps.

The other thing that makes the M2 unique among class D amps is the use of feedback to minimize distortion in the output stage. If you've ever tried a pair of noise-canceling headphones, then you have a good idea how feedback works: a microphone on the outside of the headphone picks up the noise, and built-in circuitry mixes in a mirror image of the noise to cancel it out.

Feedback systems in amplifiers don't use microphones, but the concept is the same. The output signal is compared with the input signal, and a mirror image of the difference (distortion) is introduced in order to cancel it out. This technique has been used for years in conventional amps, but has been impractical in class D amps until now. NAD collaborated with a company called Diodes Zetex on a breakthrough technology called DDFA (direct digital feedback amplifier) for the M2.

DDFA requires an extremely robust processor in order to feed the inverted error data back fast enough. If you comprehend such things, the Zetek chip operates at a 108MHz sample rate on a 35-bit-wide data path. The M2 is the first, and for now the only, vehicle on this superhighway.

Advanced power supplies

Class D amplifiers require hefty and exceptionally quiet power supplies. These parts are large, heavy and costly, but they are absolutely essential. The M2 uses three very substantial and highly efficient power supplies, one for each channel and a third for the input stage and control sections.

Excellent performance under the most demanding conditions

Digital PowerDrive™ helps the M2 maintain the lowest possible distortion and deliver breathtaking dynamics, even when driving difficult speaker loads.

Digital Soft Clipping is a new take on a technology NAD pioneered in the 1970s. In the unlikely event that you overdrive the M2, this circuit prevents the harsh sound and potential speaker damage that can result when the overdriven amplifier clips the tops and bottoms of the music signal's waveform.

Multi-stage fail-safe protection prevents amplifier or speaker damage. Short circuit, DC offset, overheat, and over current faults are handled instantly and an indication of the fault is displayed on the front panel.


  • 250 watts x 2 channels into 8 ohms (20-20,000 Hz) at 0.004% THD
  • 250 watts x 2 channels into 4 ohms (20-20,000 Hz) at 0.004% THD
  • Direct Digital design yields 90 percent amplifier efficiency
  • 4-ohm capability allows use with a wide range of speakers
  • signal-to-noise ratio: 119 dB
  • PowerDrive™ circuit with automatic speaker impedance sensing delivers maximum dynamic power output regardless of speaker load
  • five position digital impedance compensation filter lets you fine-tune the top octave to match the speaker impedance
  • Digital Soft Clipping (switchable)
  • 4 digital audio inputs (2 optical/2 coaxial)
  • one pair RCA analog audio inputs
  • one pair balanced XLR analog audio inputs
  • selectable 48, 96 or 192kHz sample rate for analog-to-digital conversion
  • digital audio processor loop lets you connect to a computer to take advantage of room correction/equalization programs
  • two pairs of custom gold-plated speaker binding posts permit bi-wiring
  • 12-volt trigger input and output
  • 1 IR input
  • RS-232 interface for advanced custom installations
  • detachable AC power cord
  • remote control
  • weight: 44.5 lbs.
  • 17-1/8"W x 5-7/8"H x 20-7/8"D
  • warranty: 3 years
  • Our 60-day money-back guarantee
  • floating ground design means M2 cannot be used with external devices such as speaker switchers or headphone adapters that connect left and right channels together

Hands-on research from the Crutchfield Labs (what are the Labs?)

Features and Specs
Watts RMS per Channel (8-ohms) 250
Watts RMS per Channel (6-ohms) ---
Watts RMS per Channel (4-ohms) 250
Frequency Bandwidth 20-20k
THD 0.004%
Minimum Impedance 4 ohms
Signal to Noise Ratio 119
Number of Inputs 7
Phono Inputs No
Preamp Outputs No
Width (inches) 17-1/8
Height (inches) 5-7/8
Depth (inches) 20-7/8
Weight (pounds) 44.5
Parts Warranty 3 Years
Labor Warranty 3 Years
Product Research
What's in the box?

Download owner's manual

  • Integrated amplifier
  • 70" Power cord
  • Wireless remote control (M2)
  • 2 "AA" batteries
  • Owner's manual (English/ French/ Spanish/ Italian/ German/ Dutch/ Swedish/ Russian)
  • Warranty information

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team — they open the box, verify contents, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.



Overview: The M2 is a new design of Direct Digital Amplifier, it can accept a digital PCM input directly so the noise and distortion typically added by cascaded analog amplifying stages is completely eliminated. This streamlining of the internal architecture can reduce the residual noise of the overall system by a factor of three. The M2 uses three power supplies; each channel has a dedicated high current power supply in a dual mono configuration and the input stage and control sections have their own dedicated supply with multiple regulated secondary voltages for individual sections.

Inputs: Being a Direct Digital Amplifier, the M2 mates well with digital sources. There are two coaxial, one XLR, and two optical digital inputs. There are also two analog inputs, one XLR and one RCA, fed through a state of the art analog-to-digital converter.

Direct Digital Feedback: Direct Digital Feedback operates simply by determining the pulse area error, no matter what the cause, and passing this information back to the digital domain where compensation can be made. Conventional amplifier feedback circuit design is too slow to work well with this type of digital amplifier, so the direct digital feedback technology was developed to deliver the solution. A feedback error signal is generated through comparison with a reference signal and then converted to the digital domain at a 108 MHz sample rate prior to being used for digital correction. For Direct Digital Feedback to work correctly requires a very wide bit path and high speed operation. The M2's 35-bit data path allows compensation to be made without truncating any information in the original signal. Running from a master clock frequency of 108 MHz there is enough speed to keep the wide amplifier bandwidth and low noise and distortion in the audio band.

PowerDrive: NAD's PowerDrive technology measures each channel's dynamic impedance individually and computes the optimum power supply voltage required to drive the output stage for maximum power and efficiency.

Digital Soft Clipping: NAD's Soft Clipping circuit gently limits the amplifier output to minimize audible distortion when the amplifier is over-driven. Using digital precision, this behavior can be controlled; the multi-stage failsafe protection is carefully engineered in the M2 to prevent amplifier or speaker damage under fault conditions. Short circuit, DC offset, overheating, and over current faults are handled instantly and an indication of the fault is displayed on the front panel. Digital Soft Clipping can be turned off for critical listening if you prefer.

Digital Processor Loop: The optical digital input/output loop allows you to insert an external digital processor or computer to filter or equalize the signal, or route the signal through a room correction program. The digital processor loop can be applied to any of the input signals, digital or analog.

Multiple Amps: With both coaxial and optical digital outputs, multiple M2s can be used to bi-amp or tri-amp advanced loudspeaker systems.

Input Level: The volume level of the analog inputs can be trimmed individually before being converted to a digital signal, so there's no volume change when changing inputs; the range is - 9 dB to 0 dB.

Sample Rate: The sampling rate of the analog to digital converter can be adjusted; choose 48 kHz, 96 kHz, or 192 kHz. Higher sampling rates allow anti-aliasing filters to take effect further outside the audible frequency range and are generally considered to sound better, especially in the high frequencies. You may need to reduce the sampling rate if you are using the digital processor loop, as many external devices will not operate at 96 kHz or 192 kHz.

Impedance Compensation: A digital impedance compensation filter allows fine tuning of the top octave to match the chosen speaker impedance; this can result in perfectly flat frequency response at 20kHz. Options include 2 Ω, 4 Ω, 5 Ω, 6 Ω, 7 Ω, 8 Ω, and >8 Ω.

Input Names: The name displayed for each input can be reassigned, up to 20 characters.

Remote Control: The M2 wireless remote will control the amp and a compatible NAD CD, SACD, or DVD player.


Front Panel:

  • Power: toggle between power on and standby
  • Input: individual buttons for each of the seven inputs; coax 1, coax 2, optical 1, optical 2, aes/ebu (digital XLR), balanced (analog XLR), and single ended (analog RCA)
  • Loop: engage/disengage the optical digital input/output loop
  • Volume: rotary volume control; also used with the menu function

Rear Panel:

  • Power: master power switch
  • Soft Clipping: on/off
  • 12 Volt Trigger: auto/off; when in auto position the front panel and remote power buttons are disabled


Rear Panel:

  • Speakers: the speaker binding posts will accept single banana plugs, pin connectors, spade lugs up to 0.59" wide, and bare wire up to 10 gauge; a second set of binding posts is for bi-wiring your speakers
  • Coax Inputs: two single RCA coaxial digital inputs; coax 1 and coax 2
  • Coax Output: single RCA coaxial digital output
  • Optical Inputs: two Toslink optical digital inputs; optical 1 and optical 2
  • Optical Output: one Toslink optical digital output
  • Loop Input: Toslink optical digital input for the processor loop
  • AES/EBU: single XLR digital input
  • Analog Inputs:
    • stereo XLR input
    • stereo RCA input
  • 12 Volt Trigger Input: 3.5mm mini-jack; turn the amp on/off along with another component
  • 12 Volt Trigger Out: 3.5mm mini-jack; turn on/off another device along with the M2
  • IR In: 3.5mm mini-jack input, used to control this unit using an optional infrared repeater or the IR output of another component
  • RS 232: the RS-232 port allows connection to a compatible PC or external whole-house control system from companies such as AMX or Crestron
  • Ground: terminal for grounding the chassis of the amp
  • AC Input: 3-pole IEC power input for use with included cord (or optional upgraded cord)


Amplifier Section:

  • Continuous Power: 250 watts x 2 into an 8Ω or 4Ω load, 20 Hz - 20 kHz, no more than 0.004% THD
  • Dynamic Power:
    • 8Ω: 300 watts x 2
    • 4Ω: 450 watts x 2
    • 2Ω: 650 watts x 2
  • Rated Distortion: 0.004% (20 Hz - 20 kHz from 500 mW to rated power)
  • Signal/Noise:
    • >95 dB (ref 1 watt)
    • >119 dB (ref 250 watt)
  • Damping factor: >2000 (ref 20-200 Hz)
  • Maximum Output Current: >27 amps
  • Power Requirement: AC 120V 60Hz
  • Weight: 44.5 lbs (20.2 kg)

Digital Inputs:

  • Input impedance:
    • Coaxial: 75 Ω
    • AES/EBU: 110 Ω
  • Sample Rate: 32 kHz - 192 kHz
  • Frequency Response: 20 Hz - 20 kHz (+/- 0.5 dB)
  • Channel Separation: 90 dB (10 kHz, 4Ω, 1/3 rated power)

Analog Inputs:

  • Input impedance: 36 kΩ/200 pF
  • Input sensitivity:
    • 318 mV (at 100 watts)
    • 503 mV (at rated power)
  • Frequency response: 20 Hz - 20 kHz (+/- 0.3 dB)
  • Channel Separation: 80 dB (10 kHz, 4Ω, 1/3 rated power)
Be the first to review this product
Great Gear Giveaway rewards card

Submit a review and then enter to win a $500 rewards card

Review this product:

Thanks for taking the time to share your experiences about this product. Please be sure to focus your comments on the product itself. Read our Review Guidelines for more information.

Your email won't be visible. Please use the email address that is associated with your order.
(e.g., JohnD) Your review will be signed using the display name and location
(e.g., Charlottesville, VA)

Click on a star to rate the overall product on a scale of 1-5
1500 characters left
Attach a YouTube Review
Crutchfield Video Review Guidelines
  • Only submit videos that you made or are authorized to use.
  • Do not submit videos that contain music, video or visuals that are copyrighted and belong to someone else.
  • Please see our Review Guidelines for more information.
500 characters left
500 characters left

Add accessories for the NAD Masters Series M2

Connect your speakers to your new amp using superior grade wire for the best results. See all categories & accessories

Original Monster Cable With gold pin connectors (15-foot pair)
36 people say
Your Price: $39.99
Add to Cart
AudioQuest Type 4 Speaker cables with pre-attached banana connectors (10-foot pair)
22 people say
Your Price: $248.99
Add to Cart
AudioQuest Golden Gate Stereo interconnect cable with RCA plugs (0.6 meter/2 feet)
16 people say
Your Price: $64.99
Add to Cart
Monster Cable Stereo Audio 200i Stereo interconnect cables with RCA plugs (1 meter/3.3 ft.)
15 people say
Your Price: $19.95
Add to Cart
AudioQuest Big Sur Stereo interconnect cable with RCA plugs (0.6 meter/2 feet)
3 people say
Your Price: $96.99
Add to Cart
AudioQuest Sydney Stereo interconnect cable with RCA plugs (0.6 meter/2 feet)
6 people say
Your Price: $154.99
Add to Cart
AudioQuest Columbia Stereo interconnect cables with RCA plugs (2-meter/6.6 feet)
1 person says
Your Price: $644.99
Add to Cart
AudioQuest Evergreen Stereo interconnect cable with RCA plugs (0.6 meter/2 feet)
39 people say
Your Price: $31.99
Add to Cart
Monster Cable Stereo Audio 400i Stereo interconnect cables with RCA plugs (1 meter/3.3 ft.)
6 people say
Your Price: $39.95
Add to Cart
Panamax M5300-PM Power line conditioner and surge protector
15 people say
Your Price: $539.99
Add to Cart
Panamax M5400-PM Power line regulator and surge protector
6 people say
Your Price: $739.99
Add to Cart
Furman Elite-15 PFi Power line conditioner and surge protector
10 people say
Your Price: $699.00
Add to Cart
Panamax MX5102 Home theater power management with surge protector and battery backup
Your Price: $649.99
Add to Cart
Panamax MB1000 Uninterruptible power supply (UPS), voltage regulator, and surge protector
Your Price: $799.99
Add to Cart
Furman IT-Reference 15i Power line conditioner and surge protector with isolation transformer
1 person says
Your Price: $2,199.00
Add to Cart
Panamax MB1500 Uninterruptible power supply (UPS), voltage regulator, and power conditioner
Your Price: $1,299.99
Add to Cart
Panamax MR4000 Power line conditioner and surge protector
1 person says
Your Price: $199.99
Add to Cart
Panamax MR4300 Power line conditioner and surge protector
1 person says
Your Price: $299.99
Add to Cart
Panamax MR5100 Power line conditioner and surge protector
1 person says
Your Price: $439.99
Add to Cart
AudioQuest NRG-2 High-quality replacement AC power cable (6 ft.)
7 people say
Your Price: $168.99
Add to Cart

Why choose SquareTrade?

The #1-Rated Protection Plan

Thousands of people have reviewed SquareTrade Protection Plans — and made us #1.

5-Day Service Guarantee & Free Shipping

We'll repair or replace your item in five business days or less after we've received it, or your plan is free. And, as always, we pay for all shipping.

Protection from Normal, Everyday Use

Repairing your average mechanical or electrical failure can cost as much as buying a new device. With SquareTrade, you're covered — including parts and labor.

3 Year Protection Plan
3 Year Protection Plan
Your Price: $379.99
Add to Cart
4 Year Protection Plan
4 Year Protection Plan
Your Price: $599.99
Add to Cart

For a more in-depth review and enhanced detailed information on the NAD Masters Series M2, please visit the Crutchfield website product page (/ISEO-rccbcspd/p_745M2/NAD-Masters-Series-M2.html ).

Find the gear that's right for you
Ask an expert
Your Crutchfield Advisor knows the gear inside and out.
Call 1.888.955.6000
Ask an expert

Compare with other NAD models

  • NAD Masters Series M2
  • Deliver even more pristine power to your speakers
  • Low Stock
  • The NAD Masters Series M2 features:
    • 250 watts per channel
    • Master Series interference-resistant housing
    • 2 bridge-tied load power amps per channel
  • Add To Cart
  • NAD C 390DD
  • Direct digital integrated amp
  • 3.5 out of 5: In Stock
    • The NAD C 390DD offers:
      • 150 watts x 2
      • all preamp functions are executed in the digital domain for transparent, dynamic, and detailed sound quality
      • internal digital-to-analog converter (DAC) technology features 35-bit architecture and 108MHz master clock
  • Add To Cart
  • NAD Masters Series M2
  • Direct Digital integrated Amplifier
  • Low Stock
    • The NAD Masters Series M2 offers:
      • 250 watts x 2
      • ground-breaking Direct Digital design
      • 4 digital audio inputs and 2 analog audio inputs (1 balanced XLR)
  • Add To Cart
You are here