Lightning Strike Monitor Series

1 Farad High Performance Capacitor

Power Rating for this Capacitor 1000 Watts

Strike

Capacitor Features:

10 Segment Tri-Color LED Display

Monitors Capacitor Charge Level

ON/OFF/Reverse Polarity Indicator

LED Status Display on Top of Cap

Made in USA

Genuine Lightning Cap Quality

Through-Post Design

Ensures Maximum Voltage Output

ESR less than 1.5 milliohms

Delivers up to 10,000 Amps Instantly!

Super high Gain Foil

Extreme Energy Storage Capacity

Mounting Brackets

Included in this Package

(MECP logo) #LSM10TB

(Back)

Craving for power? Get the juice you need by installing a world-renowned

on the Capacitor with the end marked " + " on the positive (+) terminal of

the Cap. Hand tighten the supplied terminal screws to secure the charge

card in place on both terminals. Connect the RED wire to a 12V power source.

Connect the BLACK wire to GROUND. The green LED on the charge card

should light. When the green LED goes out, your cap is charged.

TO DISCHARGE your cap: simply place the charging card on your Cap with the

end marked " + " on the positive (+) of the Cap. Hand tighten the supplied

terminal screws to secure the charging card in place on both terminals. Connect

the RED and BLACK wires together. When the red LED goes out, your Cap is discharged.

Tap in to the positive output of the battery with the correct gauge wire for your system.

Within 18" (0.5m) of the battery, place a fuse on the positive wire.Run this positive wire

to the positive (+) terminal of the Strike Cap to connect it to the battery, and then to the

amplifier's power connection. Mount the Cap close to the amplifier, keeping the positive

wire within 18" (0.5m) to reduce voltage loss in the cable. Use the same gauge wire the amplifier

accepts. DO NOT place any fuses between the Cap and amplifier! Using wire terminals, ground

the negative (-) unmarked terminal of the Lightning Cap to the nearest chassis ground point. If

you reverse the positive and negative wires the "ON" light on Cap top will glow red, indicating

extreme stupidity. Connect remote terminal screw on Cap top to switched remote lead on source

unit. See System Diagram below.

Start Vehicle. Turn on system and play at LOW volume. Turn Sensitivity knob on Cap top with

small screwdriver until a few bars are lit. Gradually turn clockwise and stop when all bars are lit.

This is your max charge level.

see Warranty and Caution info on cards below Cap

Taking the Industry by Storm Arizona, USA

www.LightningAudio.com

From the round inserts located under the cap:

(Front)

Lightning Audio

CAUTION INFO

please read

(Back)

Large electrolytic capacitors do not like heat, oil, grease, water, or mistreatment. If the Strike Capacitor

housing is deformed during installation, many layers of foil material will be damaged inside the Capacitor

and it should not be installed. Install in a safe, dry location within 18" (0.5m) of the amplifier. Observe

correct polarity: positive terminal is marked with a (+) symbol, (-) terminal is not marked. Do not block

vent plug on top of Cap. If the Capacitor is wired in reverse of marking on Cap topthe electrolytic fluid

inside the Capacitor will vent, possibly causing damage to interior of vehicle. Use extreme caution when

handling these capacitors. To avoid any problems with your capacitor, treat it like a fully charged lead acid battery.

Second Insert:

(Front)

Lightning Audio

WARRANTY

(Back)

Strike Caps will provide many years of service if installed correctly. If your Strike Capacitor proves to be

defective, contact your Authorized Dealer or Lightning Audio at 800 726-8178 for warranty instructions.

All Lightning Strike Caps are under warranty for a period of one year from date of purchase. A Return

Authorization form and copy of invoice showing date of purchase must accompany all warranties. Return

Authorization number must be clearly marked on the outside of the box or it will be returned.

If the Strike Capacitor vent plug is blown or leaking from switched polarity or has been dented or misused

it is not covered under warranty. Stripped terminals are not covered under warranty, but will be replaced for

a nominal charge of $30 to be paid when the Cap is returned to Lightning Audio.

[#495LSD10TB]

From the paper insert on the packaging:

(Front)

Lightning Strike Digital Monitor

1 Farad High Performance Capacitor

Power Rating for this Capacitor 1000 Watts

Strike

Capacitor Features:

Digital LED Voltage Display

Precise Power Readout to One Decimal

Audible Reverse Polarity Warning

with LED on Front Panel

LED Power Indicator

Visual Display for ON/OFF Status

Made in USA

Genuine Lightning Cap Quality

Through-Post Design

Ensures Maximum Voltage Output

ESR less than 1.5 milliohms

Delivers up to 10,000 Amps Instantly!

Super High Gain Foil

Extreme Energy Storage Capacity

Mounting Brackets

Included in this Package

(MECP logo) #LSD10TB

(Back)

Craving for power?Get the juice you need by installing a world-renowned

TO CHARGE your Cap: place the charging card (supplied in this package)

on the Capacitor with the end marked " + " on the positive (+) terminal of

the Cap. Hand tighten the supplied terminal screws to secure the charge

card in place on both terminals. Connect the RED wire to a 12V power source.

Connect the BLACK wire to GROUND. The green LED on the charge card

should light. When the green LED goes out, your cap is charged.

TO DISCHARGE your cap: simply place the charging card on your Cap with the

end marked " + " on the positive (+) of the Cap. Hand tighten the supplied

terminal screws to secure the charging card in place on both terminals. Connect

the RED and BLACK wires together. When the red LED goes out, your Cap is discharged.

Capacitor Installation

Tap in to the positive output of the battery with the correct gauge wire for your system.

Within 18" (0.5m) of the battery, place a fuse on the positive wire.Run this positive wire

to the positive (+) terminal of the Strike Cap to connect it to the battery, and then to the

amplifier's power connection. Mount the Cap close to the amplifier, keeping the positive

wire within 18" (0.5m) to reduce voltage loss in the cable. Use the same gauge wire the amplifier

accepts. DO NOT place any fuses between the Cap and amplifier! Using wire terminals, ground

the negative (-) unmarked terminal of the Lightning Cap to the nearest chassis ground point. If

you reverse the positive and negative wires the "ON" light on Cap top will glow red, indicating

extreme stupidity. Connect remote terminal screw on Cap top to switched remote lead on source

unit. See System Diagram below.

Adjusting Display

Start Vehicle. Turn on system and play at LOW volume. Turn Sensitivity knob on Cap top with

small screwdriver until a few bars are lit. Gradually turn clockwise and stop when all bars are lit.

This is your max charge level.

see Warranty and Caution info on cards below Cap

Taking the Industry by Storm Arizona, USA

www.LightningAudio.com

From the round inserts located under the cap:

(Front)

Lightning Audio

CAUTION INFO

please read

(Back)

Large electrolytic capacitors do not like heat, oil, grease, water, or mistreatment. If the Strike Capacitor

housing is deformed during installation, many layers of foil material will be damaged inside the Capacitor

and it should not be installed. Install in a safe, dry location within 18" (0.5m) of the amplifier. Observe

correct polarity: positive terminal is marked with a (+) symbol, (-) terminal is not marked. Do not block

vent plug on top of Cap. If the Capacitor is wired in reverse of marking on Cap topthe electrolytic fluid

inside the Capacitor will vent, possibly causing damage to interior of vehicle. Use extreme caution when

handling these capacitors. To avoid any problems with your capacitor, treat it like a fully charged lead acid battery.

Second Insert:

(Front)

Lightning Audio

WARRANTY

(Back)

Strike Caps will provide many years of service if installed correctly. If your Strike Capacitor proves to be

defective, contact your Authorized Dealer or Lightning Audio at 800 726-8178 for warranty instructions.

All Lightning Strike Caps are under warranty for a period of one year from date of purchase. A Return

Authorization form and copy of invoice showing date of purchase must accompany all warranties. Return

Authorization number must be clearly marked on the outside of the box or it will be returned.

If the Strike Capacitor vent plug is blown or leaking from switched polarity or has been dented or misused

it is not covered under warranty. Stripped terminals are not covered under warranty, but will be replaced for

a nominal charge of $30 to be paid when the Cap is returned to Lightning Audio.