Features
Enclosure Compatibility
Features
Dual Voice Coils: For increased
system flexibility, the woofer has two 4 ohm voice coils. When the voice coils
are wired in parallel the woofer presents a 2 ohm load. When the voice coils
are wired in series the woofer presents an 8 ohm load. In addition, each coil
may be connected to a different amplifier channel and each channel will see a 4
ohm load.
Square Design: By making the
Solo-Baric square, Kicker is giving you the most possible cone area (Sd) for
a given size baffle, 16% to 20% more area than a conventional round subwoofer. More
cone area means the Solo-Baric L5 moves more air, resulting in louder, deeper
bass.
Cone Materials: The square cone
is made of SoloKon,
an ultra high performance composite, which remains rigid, minimizes cone flex
and lowers harmonic distortion. SoloKon
consists of a unique one-piece, aluminum vapor-deposit material that moves as a
lightweight piston, exhibiting power and control. A rear cone brace integrates
into the SoloKon with a continuous contact
perimeter weld, which offers unmatched strength and resistance to deformation
under pressure.
Surround: The tough, flexible
Santoprene rubber surround has a long-throw, positive-roll design, which
controls extreme cone excursion and is highly tear-resistant. The corners of the
surround are ribbed to ensure linear cone motion. The surround is stitched to
the reinforced cone edge, making separation between them virtually impossible,
even in the harshest conditions.
Spider: The woofer is equipped
with a wide poly-cotton spider which easily handles high cone excursions due to
its increased diameter and unique shape.
Enhanced BAM (Basket And
Motor) Assembly: The Solo-Baric L5 utilizes a high strength stamped steel
basket which features a low-profile open design and provides a solid foundation
for the precision-aligned motor assembly. Perimeter venting in the BAM relieves
pressure from under the spider, supports linear excursion, and helps dissipate
heat from the voice coil and motor structure.
UniPlate Construction: The
Solo-Baric L5 features a one-piece UniPlate construction with a vented
hyper-extended pole piece and backplate. This unique design provides the
following benefits:
- Optimizes heat transfer
efficiency for cooler operation and maximum power handling ability
- Eliminates erratic magnetic flux
from the voice coil gap
- Releases pressure under the
suspension for uniform cone movement and responsive low bass
- Prevents the voice coil from
bottoming out and corresponding damage
Tinsel Lead Wires: The sleeved,
high-power tinsel lead wires eliminate broken leads and power loss due to the
common use of insufficient-gauge lead wires. The lead wires are stitched to the
spider to relieve stress on the connections.
Rubber Magnet Boot: A black
rubber boot covers the outside edge of the magnet structure to improve the
cosmetics of the woofer and protect the magnet from chipping or breaking during
installation.
Speaker Terminals: The
terminals are spring loaded and nickel-plated for solid connections with heavy
gauge speaker
wire, up to 11 gauge.
Break-in Period:
Due to the complex nature of Kicker Solo-Baric L5 woofers, they require a
break-in period in order to produce optimum low-bass response. The
high-performance suspension system makes the speakers very stiff
"out-of-the-box". Approximately 2 weeks of daily playing will allow
the suspension to break-in and reach its optimum equilibrium. A
"broken-in" subwoofer will exhibit stronger bass performance, smoother
response, and greater low-bass extension.
Enclosure
Compatibility
Power Handling: The
power handling specifications differ according to the type and size of the
enclosure. The power handling specifications assume that both voice coils are in
use. Note: Both voice coils in a dual voice coil speaker should always be
connected.
Recommended Sealed Box Volume:
- Compact (minimum enclosure volume):
0.88 cu/ft; the woofer can handle up to 600 watts RMS
- SQ (maximum enclosure volume): 2.0
cu/ft; the woofer can handle up to 500 watts RMS
Recommended Vented Box Volume:
- Compact: 1.75 cu/ft; 2.5" x 13.25"
port opening; 22.5" port length; the woofer can handle up to 600 watts RMS
- SPL/Deep Bass: 3.25 cu/ft; 3" x
13.25" port opening; 14.5" port length; the woofer can handle up to 600
watts RMS
Note: The power handling
specifications listed with the vented enclosure recommendations apply only
when a 25Hz, 24dB/octave subsonic filter (sold separately) is used with this
woofer. If a subsonic filter is not used, power handling may decrease,
excessive port noise can occur, and the life of the woofer may be shortened.
Cutout:
The woofer will not mount in a standard enclosure with a round cutout. Instead,
the woofer must be mounted in an enclosure with a 11" x 11" square opening.
