car stereos & components?
2005-12 Nissan Xterra
2005 • 2006 • 2007 • 2008 • 2009 • 2010 • 2011 • 2012
2005 Nissan Xterra (Crutchfield Research Photo)
The Nissan Xterra has enjoyed wide appeal since its introduction, and held a singular position in Nissan’s product mix until 2008, when the Nissan Rogue was introduced. In 2005, Nissan increased the Xtrerra’s overall size and introduced a number of performance and luxury amenities. These included expanded power-train options for more horsepower, and more comfortable interior appointments. At the same time, they added a new stereo package to the mix, and entertainment options like satellite radio. Today, the Xterra's sporty body style and performance help it continue to hold its own in the mid-sized SUV category.
A Rockford Fosgate stereo was optional in some 2005-08 Xterra models (Crutchfield Research Photo)
Factory stereo system
The 2005-2008 Xterra offered two stereo systems to choose from. The base package offered an AM/FM/CD receiver driving six speakers. All systems carried tweeters in each corner of the dash, with oval 6"x9" woofers mounted in the lower front doors, and circular 6-3/4" woofers located in the rear doors.
The Rockford Fosgate premium system had a 6-disc CD changer in the dash that featured MP3 playback. Later models also added an auxiliary input. The standard speaker package was replaced by a 9-speaker system powered by a Rockford Fosgate amplifier. Besides having better speakers, the premium system added tweeters in the rear doors, and the ninth speaker was an 8" powered subwoofer located under the driver’s seat
Replacing your factory stereo
Removing the stereo is fairly simple, unless your stereo is integrated into the dash panel (found on some 2009-up models). Those vehicles require a little more work once the stereo is out of the dash, but we’ll get to that scenario in a minute. The Xterra offers plenty of room behind the dash panel and you can select either a single-DIN (2" tall) or a double-DIN(4" tall) stereo, so you’ll be able to choose from many aftermarket stereos.
One quick note about the Rockford Fosgate system: When you replace the stereo in these systems, you can safely use the factory amplifier with your new stereo, and the receiver wiring harness you get from Crutchfield will enable you to connect it properly. However, your new receiver must have two sets of preamp outputs (front and rear) or you’ll lose the ability to fade the music from front to back. Keep this in mind when shopping for a receiver.
With the trim panel out of the way, it's time to remove the stereo (Crutchfield Research Photo)
When removing the stereo, you'll start by using a panel tool to carefully pry up the plastic tray on top of the dash above the radio. Remove the screw that you find underneath the tray. Pry out the trim panel around the receiver and climate controls, and unplug the harnesses from it. Remove the four Phillips screws holding the stereo in place, then pull out the stereo and disconnect the wiring plug and FM antenna.
Integrated radio: For those newer models that have the radio integrated into the dash panel (shown here), dash disassembly and removal is the same. But when you pull the dash trim off, you’ll find that the radio is attached to it, instead of the dash substructure. So once you’ve unplugged all the harnesses, flip the dash/radio assembly upside down and find the four screws that secure the radio to the dash panel.
Factory stereo integrated into the dash (Crutchfield Research Photo)
No matter which type of factory stereo you have, you’ll need a mounting kit to install the new receiver, a wiring harness to make the electrical connections without cutting into your Nissan’s wires, and an adapter for the FM antenna cable. (All of these are included free with most receiver purchases from Crutchfield; and if not free, you’ll pay a maximum of $15 for them.) If you’re installing a double-sized receiver, you’ll need to use the mounting brackets attached to the sides of the factory stereo. If you no longer have these brackets, you’ll need to get replacements from a Nissan dealership. Follow the instructions included with the mounting kit to install it, then install the new stereo according to the instructions in your MasterSheet, and reassemble the dash.
Dish kits are available for the standard dash (left) and the integrated-stereo dash (right) (Crutchfield Research Photos)
Airbag light note: if your Xterra has a passenger’s side airbag, there’ll be an airbag light connected to the dash panel that you remove. You can safely detach this light from the panel by removing the screws holding the light in place. Do not take the easy road and unplug the cable from the light. Doing so will cause the computer to receive a fault code, causing the airbag light to trigger. You’ll have to take the truck to a Nissan dealership, and pay a service fee, to reset the truck’s diagnostic computer.
Tools needed: Phillips screwdriver, panel tool
Steering wheel audio controls
If you want to continue using the Xterra’s steering wheel audio controls with your new receiver, then you’ll need to install a steering wheel adapter when you add the new stereo. There are several available, but we recommend the Axxess ASWC-1 adapter because it’s the easiest to install.
Replacing your factory speakers
The Xterra's factory tweeters (Crutchfield Research Photo)
You can remove the factory tweeters without much difficulty. All you need to do is pry off the grilles, then, depending on which stereo system you have, remove either two or four screws securing the tweeter. The only difficulty lies in the fact that these screws can be hard to get to with a screwdriver. A right-angle screwdriver will save the day.
When the screws are out, lift out the tweeter and unplug the wires. To mount a new tweeter, you’ll have to fashion a bracket to hold it in place. You’ll also have to tap into the factory speaker wires because there aren’t any aftermarket adapters available for this location. We carry a universal bracket that will come in handy for this, and Posi-Product wire tap connectors can really help with the wiring.
Tools needed: Panel tool, right-angle Phillips screwdriver
Front speaker in the Rockford Fosgate system (Crutchfield Research Photo)
As mentioned earlier, the front door speakers are 6"x9" ovals in both versions of the factory stereo system. The space in front of the speakers is a little tight, so only a few aftermarket 6x9’s will fit. You can also install 6-1/2" or 5-1/4" speakers in this location, using adapter brackets that are included free when you purchase your speakers from Crutchfield. Choosing one of these smaller sizes will give you more replacement options.
There are no wiring adapters available for the Xterra, so you’ll have to splice the new speaker wires to the truck’s wiring. This is another place where the Posi-Product wire taps will be very helpful. If you use these, you won’t have to cut off the factory connectors.
The door panels will have to be removed to gain access to the speakers, but the process isn't terribly hard. There are three screws to remove, located behind the door pull, armrest, and power options switch panel. After that, just use your panel tool to pry around the bottom and sides of the door panel until you release it. Full step-by-step instructions are detailed in your MasterSheet.
Tools needed: Phillips screwdriver, panel tool, 8mm socket, ratchet & extension,
The premium sound system's rear tweeters are mounted on the underside of the door panel (Crutchfield Research Photo)
Removing the rear door panel is nearly identical to removing the front door panel. Once you have the panel off, you can install 6-1/2" or 5-1/4" speakers, again with the help of a mounting bracket. You’ll also have to drill new mounting holes for the bracket. Simply attach the bracket to the new speaker, then hold it in place so you can mark the screw holes with a pen or marker. Set the speaker assembly aside and carefully drill the new holes. Once again, a wiring adapter is not available, so you’ll have to splice the wires as you did in the front doors.
Rockford Fosgate systems: If you have the Rockford Fosgate audio system, you’ll also find tweeters mounted on the inside of the rear door panel. They’re held in place by two screws and can easily be replaced. As with the dash tweeters, you’ll need to fashion a mounting bracket and splice the wires. If your new tweeters have a threaded screw hole on the back, you might even be able to re-use the Nissan brackets. The factory tweeters are 1-3/8" in diameter, so your replacements shouldn’t exceed this size.
Tools needed: Phillips screwdriver, panel tool, 8mm socket, ratchet & extension, drill and 1/8" bit
JL Audio Stealthbox for the Xterra (right) (Photo courtesy of JL Audio)
Bass options for your Xterra
If you don't have the Rockford Fosgate system, your Xterra can certainly benefit from more bass. There's obviously plenty of room for a subwoofer box in the back. Shop our selection of bass packages to take the guesswork out of matching subs and amplifiers.
If you want a stealthy option that preserves your cargo space, consider the JL Audio Stealthbox® custom-fit subwoofer enclosure. It mounts against the passenger-side rear wall and contains a 12" JL Audio subwoofer capable of handling up to 500-watts RMS. Add an amp and fill your truck with hard-hitting bass.
Installing a security or remote start system in your Xterra is pretty straightforward—for a security system. This is never an easy job and most people should leave it to a professional. All of the necessary wiring connections can be found under the driver's side of the dash. You'll want to add the FlashLogic FLCAN module whether you're adding security or remote start. It'll make the installation much easier.
You can add iPod and iPhone control to your Xterra's factory stereo, using the iSimple iPod adapter. You can control the music on your iPod from the Nissan stereo, and keep your device charged, too. Given the cost of this adapter, you might want to go ahead and replace the stereo to get similar control and better sound. But if you want to keep the factory stereo, it's good to know that you do have another option.
Good, better, best
Good: The Xterra’s speakers are okay, but you’d do well to replace them with better cones, especially if you don't have the Rockford Fosgate system. If you do have the premium system, then start your upgrades by replacing the stereo.
Better: Once you have good speakers and maybe a stereo that's capable of helping you tune the sound, it's time to add bass. No stereo system is complete without a subwoofer, and in a vehicle this size, maybe even two. If you have the premium system, then you already have the 8" powered sub under the front seat. You can still benefit from adding a 10" or 12" subwoofer in the back of the truck.
Best: Obviously, the final building block for this system is more power. Adding a 4-channel amp to the speakers will pull even more detail out of your music, and make it sound better especially when you're listening at lower volumes.
Keep in mind, there's no magic formula to creating a great-sounding audio system. The options presented above can actually be done in just about any order. What matters is that you invest in an improved sound system and enjoy cruising around in your Xterra for years to come.
A homepage for your vehicle
Tell us about your vehicle, and you'll be able to see:
New to Crutchfield? Here are 3 things we want you to know about us.
Custom Car Showroom