Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere.
That's because we have our own in-house Product Research team — they open the box,
verify contents, check the owner's manual, and record dimensions, features and specs.
We stay on top of new products and technologies to help people make informed choices.
Features
Controls
Inputs and Outputs
Specifications
Warranty Note
Features
Cosmetics: The
amplifier is black and it has a dark gray, removable metal shroud. Though this
is one 4-channel amplifier, Kicker uses the terminology of "Amp 1" and
"Amp 2" to indicate the channels.
Amplifier Shroud:
The amplifier has a metal shroud that must be removed before installation,
allowing access to the amplifier's inputs and outputs. Once the amplifier is
installed and all the connections are made, you can re-install the shroud to
hide the connections on the amplifier, or leave the shroud off to save space.
With the shroud removed, the amp has the following dimensions: 12.375"W
(13.500" with RCA's) x 9.541"D x 2.313"H.
Kicker "Living Loud"
Certified Power Certificate: The
amplifier comes with a certificate that informs you of the total maximum wattage
of the particular amplifier, along with the model number, serial number, tested
date, and whether the amplifier passed the total harmonic distortion,
signal-to-noise ratio, and protection circuit tests.
Speaker-level Inputs:
Two high-level input connections are included to allow use with sources that do
not have RCA preamp level outputs.
Built-in Variable Electronic
Crossover: There are two
built-in crossovers that allow you to select high-pass for satellite speakers,
low-pass for subwoofers, or bypass for full-range operation. The crossover
frequency is variable from 50 to 200Hz.
SORT (Short
circuit, Over-voltage, Reverse polarity, Thermal)
Protection Circuitry: The
SORT protection circuitry guards against accidents and undesired operation. The
Power LED on the left side of the amp glows green and the power indicator on top
of the amp glows red when the amplifier is hooked up correctly and SORT has not
been engaged. If the red Protection LED illuminates, SORT has been engaged and
the amplifier is in protect mode until the problem is resolved.
KickBass Bass Boost: The
two KickBass bass boost circuits provides up to 18dB signal boost at 40Hz.
SAMS (Stereo And Mono
Simultaneously): With a
Tri-mode adapter (item # 127TM100), this amplifier can run satellite speakers
and a sub at the same time.
Controls
Top of Amplifier:
- KickBass Bass Boost Control for
Amp 2: rotary control
that allows you to adjust the bass boost, centered at 40Hz, from 0 to +18dB
- Gain Control for Amp 2:
rotary gain control that allows you to adjust the output level
- Variable Crossover Frequency
Control for Amp 2: allows
you to adjust the crossover frequency from 50-200Hz
- KickBass Bass Boost Control for
Amp 1: rotary control
that allows you to adjust the bass boost, centered at 40Hz, from 0 to +18dB
- Gain Control for Amp 1:
rotary gain control that allows you to adjust the output level
- Variable Crossover Frequency
Control for Amp 1: allows
you to adjust the crossover frequency from 50-200Hz
Right Side of Amplifier:
- Two Crossover Mode Switch:
allows you to select "Hi Pass", "Lo Pass", or Off. There
is one switch for Amp 1 and one for Amp 2.
Inputs
and Outputs
Left Side of Amplifier:
- 12+ (power):
gold-plated screw terminal (terminal is 0.554" wide)
- REM (remote turn-on):
gold-plated screw terminal (terminal is 0.350" wide)
- GND (ground):
gold-plated screw terminal (terminal is 0.554" wide)
- Fuse: two
20-amp fuses
Right Side of Amplifier:
- Amp 1 Speaker Output:
gold-plated screw terminal (each terminal is 0.350" wide)
- Amp 1 High Level Input: Molex
plug input for included harness
- Amp 2 High Level Input: Molex
plug input for included harness
- Amp 1 RCA Input: gold-plated
RCA line input jacks
- Amp 2 RCA Input: gold-plated
RCA line input jacks
- Amp 2 Speaker Output:
gold-plated screw terminal (each terminal is 0.350" wide)
Specifications
Dynamic Power
Rating (measured at 14.4V):
- Bridged
Into A 4-Ohm Load: 150
watts x 2
- Per Channel Into A 2-Ohm Load:
75 watts x 4
- Per Channel Into A 4-Ohm Load:
60 watts x 4
Continuous Power
Rating (measured at 13.8V):
- Bridged
Into A 4-Ohm Load: 150
watts x 2
- Per Channel Into A 2-Ohm Load: 75
watts x 4
- Per Channel Into A 4-Ohm Load:
38 watts x 2
Warranty
Note
Warranty Note: The
warranty on this amplifier is 1 year parts and labor. If installed by an
authorized dealer, the warranty is extended to 3 years parts and labor.