About the Sony XM-SD22X
Sony's Xplod Specialty Series amps keep the sound strong all day long! MOSFET power supplies and output stages ensure you'll have a steady stream of power, even when the amp is subjected to high demand. Xplod amps are CEA-2006 compliant so you know the power ratings are a true measure of the amp's performance!
The XM-SD22X 2-channel amplifier puts 200 watts RMS power per channel (or 500 watts RMS bridged) at your disposal, plenty of power for a subwoofer or two. The bass boost circuit (10 dB at 40 Hz) kicks up the lows when it's needed, and you can switch on the variable low-pass filter to keep the low frequencies tight and crisp.
The speaker-level inputs allow for easy integration with any system, even a factory radio, and the preamp outputs are a nice bonus if you're hooking up an additional amp. The cool gray finish and blue lighting look great, and all four Specialty Series amps (XM-SD22X, XM-SD46X, XM-SD51X, and XM-SD61X) have exactly the same footprint a nice touch if you're planning a multi-amp installation!
Product highlights:
- two-channel car amplifier
- 200 watts RMS x 2 at 4 ohms (250 watts x 2 at 2 ohms)
- 500 watts RMS x 1 bridged output at 4 ohms (4-ohm stable in bridged mode)
- variable low-pass filter (50-300 Hz at 12 dB per octave)
- variable bass boost (0-10 dB at 40 Hz)
- Tri-way capable (Tri-Way crossover required)
- MOSFET output stage and power supply
- CEA-2006 compliant
- preamp- and speaker-level inputs
- preamp outputs
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 15-7/8"W x 2-3/16"H x 10-15/16"D
- warranty: 2 years
- MFR # XM-SD22X
What's in the box:
- Two channel amplifier
- 8" Speaker-level input harness
- Protective terminal cover
- Four 5/8" Hex-head self-tapping screws
- Operating Instructions (English/French)
- Warranty sheet
- Impedance warning
Customer reviews for Sony XM-SD22X
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Sony XM-SD22X
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
200 x 2 | |
Peak Power Output (Watts x Channels) | 400 x 2 | |
Power at 2 Ohms (Watts x Channels) | 250 x 2 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | 500 x 1 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 5-50kHz Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 93 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | AB | |
Low-Pass Crossover Frequency | 50-300 Hz | |
Low-Pass Slope (dB/octave) | 12 dB | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0-10 dB | |
Bass Boost Frequency | 40 Hz | |
Fan Cooled | No | |
Fuse Rating | 40 x 2 | |
Speaker Level Inputs | --- | |
Preamp Outputs | 1 pair | |
Width (inches) | 15-7/8 | |
Height (inches) | 2-3/16 | |
Depth (inches) | 10-15/16 | |
Parts Warranty | 2 Years | |
Labor Warranty | 2 Years |
Product Research
Features
Inputs and Outputs Notes
Specifications
Protection Circuitry: The Sony XM-SD22X amplifier has 3-way protection circuitry which protects the amplifier in the following cases:
- Thermal: Turns the amp off when the operating temperature is too high
- Short circuit: Turns the amp off when the speaker outputs are short-circuited
- DC Offset: Turns the amp off when the amp generates direct current
LED: The amplifier has an line of four LEDs on the top panel that glow blue when the amp is on. There is also an LED that lights red when the protection circuit is activated.
Low-pass Crossover: This amp is equipped with a low-pass crossover, continuously variable from 50-300Hz, with a slope of 12dB/octave. You can turn the crossover off for full-range operation.
Bass Boost: For added low frequency performance, this amplifier has a bass boost centered at 40 Hz, variable from 0 to 10 dB.
Terminal Cover: The XM-SD22X comes with a protective cap that fits over the power wire terminal strip to help prevent accidental short circuiting.
Power/Ground Terminals: The power and ground screw terminals are 0.54" wide to easily accommodate 4-gauge wire.
Remote Terminal: The remote turn on screw terminal is 0.35" wide.
Speaker Outputs: Each speaker output screw terminal (left and right/positive and negative) is 0.35" wide.
Speaker-level Input Harness: The amp comes with a speaker-level input harness with a 4-pin Molex plug. This allows you to easily connect the amplifier to a factory radio or a receiver without preamp outputs.
Preamp Output: This amplifier includes a stereo preamp output, which allows you to send an unfiltered signal to another amplifier. Note that you must be using the line level input, not the speaker-level input, in order to use the preamp output jacks.
CEA-2006 Compliance: The specifications given by Sony for the XM-SD22X amplifier comply with the new CEA-2006 Amplifier Power Standard from the CEA (Consumer Electronics Association). All manufacturers who comply with the standard can display the CEA-2006 logo on their product.
RMS Power Rating (measured at 14.4V): 200 watts x 2 into a 4-ohm load with an input voltage of 14.4 volts
Signal to Noise Ratio: 93 dBA (1 watt into 4 ohm load)
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Works great I was not to sure how it would preform but it did very sell
Ryan from Marysville