About the Alpine MRP-M850
Outstanding audio performance you expect it when the amp is an Alpine. Alpine's V-Power amplifiers supply the high level of performance you want without shaking loose too much of your hard-earned cash.
The MRP-M850 mono amplifier will power your subwoofer with 500 watts of power. Add a second sub and the MRP-M850 pumps out 800 watts enough power for some seriously "good vibrations." The variable low-pass filter adjusts the frequency output to match your system, while the Bass EQ lets you dial in some extra boost on the lows. A subsonic filter eliminates inaudible, ultra-low bass notes for cleaner output.
The amp's machined-metal heatsink keeps the internal parts cool and distortion low even when you're cranking the volume. Gold-plated screw terminals and RCA connections resist corrosion that can degrade signal performance.
Product highlights:
- mono subwoofer car amplifier
- 500 watts RMS x 1 at 4 ohms (800 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- variable low-pass filter (50-200 Hz, 24 dB/octave)
- tuned Bass EQ (0-12 dB bass boost at 50 Hz)
- subsonic filter (24 dB at 15 Hz)
- MOSFET power supply
- STAR Topology (minimizes internal noise and prevents ground interference)
- gold-plated screw terminals
- speaker- and preamp-level inputs
- fuse rating: 25A x 3
- 4-gauge amp wiring kit with 80-amp fuse recommended wiring and hardware not included with amplifier
- 15-5/8"W x 2-3/8"H x 9-9/16"D
- warranty: 1 year
- MFR # MRP-M850
What's in the box:
Alpine MRP-M850 owner's manual
- Mono amplifier
- Three 25 amp fuses (installed)
- 7" Speaker-level input harness (8-pin Molex plug on one end and bare wires on the other)
- 2 Terminal covers
- 4 Self-tapping hex-head screws (M4 x 20mm)
- 4 Machine screws for securing terminal covers (M3 x 12mm)
- 3mm Allen wrench
- 2.5mm Allen wrench
- Owner's Manual (English/French/Spanish)
- Customer Care Registration card
Customer reviews for Alpine MRP-M850
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Alpine MRP-M850
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
500 x 1 | |
Peak Power Output (Watts x Channels) | N/A | |
Power at 2 Ohms (Watts x Channels) | 800 x 1 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 20-200 Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 70 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-200 Hz | |
Low-Pass Slope (dB/octave) | 24 dB/oct | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0-12dB | |
Bass Boost Frequency | 50 Hz | |
Fan Cooled | No | |
Fuse Rating | 25 x 3 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 16-3/8 | |
Height (inches) | 2-3/8 | |
Depth (inches) | 9-9/16 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Power Supply: The MRP-M850 amplifier's power supply uses MOSFETs to convert DC battery voltage to the higher DC voltages needed for high power. It supplies positive and negative voltages around 0V, rather than around 6V as with conventional single-polarity power supplies. The result is higher power levels and a dynamic range wider by as much as 10dB.
Low Pass Filter: The amp is equipped with a 50-200Hz variable low-pass filter with a slope of 24dB/octave. This being a mono subwoofer amp, the crossover is always engaged.
Subsonic Filter: This amp utilizes a 15Hz subsonic filter to eliminate super low frequencies that can rob power and damage speakers. The subsonic filter operates at all times, and cannot be turned off.
Bass EQ: The Bass EQ circuit provides a variable boost (0-12dB) at 50 Hz.
Inputs: The amplifier offers both line-level and speaker-level inputs for 2 channels. The supplied speaker-level input harness allows you to connect this amplifier to a receiver without preamp outputs; aftermarket or factory.
Terminal Covers: The amp comes with two plastic covers that protect and insulate the RCA, power, and speaker connections. Four supplied machine screws attach the covers to the amplifier.
Left Side Of Amplifier:
- GND (ground): Gold-plated set screw terminal, accommodates bare wire up to 4 gauge
- Battery: Gold-plated set screw terminal, accommodates bare wire up to 4 gauge
- Remote: Gold-plated set screw terminal, accommodates bare wire up to 8 gauge
- Speaker Output: Gold-plated set screw terminal, accommodates bare wire up to 8 gauge
Right Side Of Amplifier:
- Line Inputs: 1 pair of gold-plated stereo RCA jacks
- Speaker Level Input: Molex plug input for supplied 4-pin harness
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Had this amp since hurricane Katrina (2005), it's still going strong. Running it on 2 jl audio 10w1v-3s. Hear me a mile away.
Sam from Bay Saint Louis