About the Infinity Kappa Perfect 10.1
The Infinity Kappa Perfect 10.1 10" subwoofer combines a rugged aluminum cone and high-roll butyl-rubber surround to produce slammin' bass all the way down to 18 Hz. The super-rigid woofer cone won't distort (even when you push it hard), but it's light and responsive for remarkably high sensitivity. That means it'll squeeze the most volume out of the power you feed it.
The massive cast-aluminum basket and the pole-piece are vented so the 4-layer voice coil stays cool, even when the music gets hot. Infinity has subjected these subs to the most intensive testing in the industry 100 grueling hours of performance at their full RMS rating (350 watts).
The Perfect 10.1 bridges the gap between subs intended for SPL and those intended for sound quality, creating bass that hits hard and sounds great. Whether you're planning a competition system or just looking for powerful bass, this sub's ready for action.
Details:
- 10" 4-ohm subwoofer
- aluminum cone with high-roll butyl-rubber surround
- massive cast-aluminum basket
- suitable for free-air use (handles up to 175 watts in free-air applications)
- recommended power range: 75-350 watts RMS
- peak power handling: 1,400 watts
- frequency response: 18-200 Hz
- sensitivity: 94 dB
- top mount depth: 5-3/4"
- sealed box volume: 0.6 cu. ft.
- ported box volume: 1.0 cu. ft.
- Recommended Q-Logic Box Type: 1, 2
- warranty: 3 years
Priced per speaker
What's in the box:
Infinity Kappa Perfect 10.1 owner's manual
- One 10" woofer
- 1 Self-adhesive foam gasket
- Instructions
- Technical Data sheet
- Warranty card
- "Infinity" sticker
Customer reviews for Infinity Kappa Perfect 10.1
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Infinity Kappa Perfect 10.1
Features & specs
Features and Specs | ||
---|---|---|
Size | 10 -inch | |
Impedance (Ohms) | --- | |
Cone Material | Aluminum | |
Surround Material | Butyl rubber | |
Port diameter (inches) | 3 | |
Port length (inches) | 10.4 | |
Free-Air | Yes | |
Dual Voice Coil | No | |
Sensitivity |
94 dB at 2.83 volts | |
Frequency Response | 18 - 200 Hz | |
Max RMS Power Handling | 350 | |
Peak Power Handling (Watts) | 1400 | |
Top Mount Depth (inches) | 5 13/16 | |
Bottom Mount Depth (inches) | 6 1/2 | |
Cutout Diameter or Length (inches) | 9 | |
Frame Width | 10.337 | |
Frame Length | 10.337 | |
Vas (liters) | 32.13 | |
Fs (Hz) | 28.35 | |
Qts | 0.42 | |
Xmax (millimeters) | 14.15 | |
Parts Warranty | 3 Years | |
Labor Warranty | 3 Years | |
Box Requirements | ||
Ideal Sealed Box Volume (cubic feet) | 0.6 | |
Minimum Sealed Box Volume (cubic feet) | 0.6 | |
Maximum Sealed Box Volume (cubic feet) | 0.6 | |
Ideal Ported Box Volume (cubic feet) | 1 | |
Minimum Ported Box Volume (cubic feet) | 1 | |
Maximum Ported Box Volume (cubic feet) | 1 |
Product Research
Features
Enclosure Compatibility
Curvilinear Aluminum Cone: The curvilinear aluminum cone is lightweight and extremely rigid for low distortion and superior bass response.
High-roll Butyl Surround: The high-roll butyl surround damps cone resonance and ensures longevity.
Cast-Aluminum Basket: The non-resonant cast aluminum basket ensures perfect alignment of the speaker's moving parts.
Flat Uniform-roll Spider: The spider design provides maximum control over cone motion at the limits of the speaker's excursion, and reduces even-order harmonic distortion compared to cupped spiders.
Vented Pole Piece: A flared, polished and vented pole piece is used to provide optimum cooling of the voice coil and minimize turbulence.
1.5" 4-layer Voice Coil and Stacked Magnets: The 1.5" 4-layer voice coil and stacked magnets provide high motor force and room for ultra-long excursion.
Gold-plated 5-way Binding Posts: The gold-plated 5-way binding posts will accept pin connectors, spade connectors, banana plugs, dual banana plugs, and bare wire.
Recommended Sealed Box Volume: Infinity recommends a sealed enclosure with an internal volume of 0.6 cu/ft.
Recommended Ported Box Volume: Infinity recommends a ported enclosure with an internal volume of 1.0 cu/ft. One 3" diameter x 10.4" long port should be used with a 1.0 cu/ft enclosure.
Recommended Sealed Bandpass Box Volume: Infinity recommends a bandpass enclosure with an internal volume of 0.95 cu/ft. The 0.95 cu/ft enclosure should have a sealed chamber volume of 0.6 cu/ft and a ported chamber volume of 0.35 cu/ft. One 3" diameter x 10.04" long port should be used in the ported chamber.
Free-air Mounting: In addition to being compatible with sealed, ported and bandpass enclosures, the woofer can be used in free-air applications. A free-air subwoofer is designed to be mounted on a baffle board, which separates two areas of the vehicle. For instance, you could mount this woofer to a board attached to the rear deck or placed in the trunk against the rear seat. The trunk acts as the enclosure housing the subwoofer.
The Infinity Kappa Perfect 10.1 replaces these items
Infinity Kappa Perfect 10.1
- Aluminum cone
- rubber surround
- 75-350W RMS power range
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
these subs are great, i have got two hooked up in my two door civic and these subs bump and i dont even have my amp in max, great for a small car and i recomend them for anybody
Dawn from Seaford, NY