all car speakers?
Full-Range Speakers Installation Guide
Share this article:
|This installation guide offers examples of different types of full-range car speaker installations. The installation of your speakers will depend upon the make and body style of your vehicle, as well as the equipment purchased.
Installing Speakers: Easy and Effective
Installing new speakers is the single most cost-effective improvement you can make to your vehicle's audio/video system. Not only are aftermarket speakers relatively inexpensive, they are usually not difficult to install, thanks to the free brackets, wiring harnesses, and detailed instructions Crutchfield will send you when you buy your speakers from us (available for most vehicles). Of course, each car is different, but let's take a look at some of the more common speaker mounting locations, and what you might expect when installing speakers there.
Types of Installations
There are two types of speaker installations:
- Easy Fit
Easy Fit speakers fit your factory speaker openings and use factory speaker grilles and brackets.
An Easy Fit speaker will fit directly into the existing factory speaker opening.
Occasionally, you will need to use a special set of brackets or adapters to install Easy Fit speakers in your vehicle, or you may need to drill new mounting holes. Crutchfield provides these brackets and adapters free with your speaker purchase.
Easy Fit speakers will sometimes need a bracket to fit properly into the existing factory opening.
- Modify Fit
Speakers labelled as Modify Fit require modifications such as drilling new screw holes, or cutting or filing metal, plastic, or pressboard. These installations are more complicated and require more tools and time.
Modify Fit speakers may require minor additional steps such as filing a plastic speaker basket to allow for a larger magnet structure (left). In rare cases, a modify fit speaker may require you to cut a new speaker opening (right).
Replacing Dash Speakers
Although they can occasionally be tough to reach, most dash speakers are small and relatively easy to replace. In some vehicles, all you need to do is remove the grilles, which are usually held down by screws or friction fittings. If your grilles use friction fittings (you'll know because there won't be any screws evident), carefully pry them up from the edges. To avoid marring or cracking the surrounding area, put a broad, flat item, like a panel tool or putty knife, underneath whatever you're using to pry up the grille.
Other vehicles, however, require that you remove the entire dashboard panel to access the connections. Fortunately, most dash panels are held in place by just a few screws. Once you've removed them, it's just a matter of carefully pulling off the panel, making sure you don't catch any wires or ducts in the process. You'll find an offset screwdriver or stubby Philips screwdriver useful to get at the screws near the windshield.
Most dash speakers are small and relatively easy to replace.
Remove the old speakers and make sure to note the polarity of each terminal. The speaker's positive terminal is the larger of the two, and is usually marked with a "+" or a colored dot. If your speakers came with a Crutchfield wiring harness, use it to connect to your factory wiring. If not, you'll want to solder the connections from your new speakers to the wiring in the vehicle, or use crimp connectors. Don't secure the wires with electrical tape, it can deteriorate rapidly because of the temperature extremes in your car. It's also a good idea to test the speaker before you secure it tightly to be sure everything works before you put the dash back in place.
Replacing Door Speakers
Doors are the most common location for car speakers and, in many cars, the speakers found there are fairly easy to replace. Most late model cars have a notch at the bottom of the speaker grille. Simply insert a screwdriver into this slot, pop out the grille, and unmount the factory speaker. In some cars you may only need to remove a few screws to get the grille out of the way.
Removing a speaker grille from the door.
Once you have removed the grille, most factory door speakers can be removed with a phillips screw driver.
In still others, though, you'll have to remove the entire door panel to get the factory speaker out. Your Crutchfield MasterSheet will walk you through the specific procedure for your vehicle, but it's generally a pretty straightforward process.
Start by removing the window crank handles. Some are secured with a screw at the pivot point usually hidden by a piece of snap-on trim while others are held in place with a spring clip around the base. Crutchfield carries an inexpensive tool to help remove this clip, but it can be done with a small flat-blade screwdriver (use a shop rag to prevent scratching the crank). Just depress the surrounding door panel, look behind the window crank, and rotate the handle until you can see the ends of the spring clip. Then, just gently push it off with the screwdriver or tool. (The clip will pop off, so keep a close eye on it.) After removing the crank, take off the armrest (usually held on by a few screws), and the trim that fits around the handle. The only thing holding the door at this point should be the friction fittings around the edge of the panel and a few more screws.
With the screws removed, start at a bottom corner and pull the panel corner straight out. Use a panel tool around the fittings to pry out the panel. Try not to pull so hard as to break one of the friction clips. Once a corner is loose, work across the bottom and up both sides. The panel should now be hanging by the trim that hangs off of the window well. Lift straight up and it should come free.
|Click on pictures below to enlarge.|
Rear deck speakers
Installing rear deck speakers presents many of the same challenges as door speakers. In many cases the grilles on the rear deck can be easily pried up or removed by unscrewing them. Other times, they can be removed from underneath, via the trunk.
A look at a typical rear deck speaker installation.
In some cars, however, the entire rear deck panel must be removed to access the speakers. Often, this means removing the rear seat to access the deck panel. (Some seats are bolted in place, while others pop in and out.) With the seat out, you should be able to pry up the rear deck and work with the speaker openings in the same fashion as door or dash mounting locations.