About the Polk EX3560
The outstanding sound quality of the EX3 Series EX3560 6-1/2" component system is a testament to Polk Audio's commitment to sonic excellence. The rugged 6-1/2" poly/mica woofer cone reproduces bass and midrange with exceptional accuracy, aided by a butyl rubber surround and powder-coated, reinforced steel basket. A 1" silk dome tweeter delivers sparkling detail and superb imaging.
Optimize your soundstage by locating your tweeter in a suitable location, using the included flush-, surface-, and angle-mount adapters. If your vehicle doesn't have a good mounting location, the Elliptical Lens snaps over the tweeter in place of a grille, directing high frequencies toward your listening position. The high-quality crossover (high-/low-pass at 4,000 Hz, 12 dB per octave) sends frequencies to their proper destinations.
Details:- poly-mica woofer cone with butyl rubber surround
- 1" silk dome tweeter
- 2-way crossover (high-/low-pass at 4,000 Hz, 12 dB per octave)
- frequency response 50-22,000 Hz
- power range 10-100 watts RMS
- peak power handling 300 watts
- sensitivity 92 dB
- top-mount depth 2-5/16"
- 1-year warranty
What's in the box:
- 2 Woofers
- 2 Grilles
- 2 Grille frames
- 2 Tweeters installed in flush mount cups (each tweeter has an Elliptical Lens and a 23" length of speaker wire attached)
- 2 Flush mount cup clamps
- 2 Surface mount cups
- 2 Angled surface mount cups
- 2 Tweeter grilles
- 2 Crossovers
- 2 Self-adhesive foam gaskets
- Two 10' lengths of speaker wire (each length of speaker wire has bare wire on one end and female quick-slides on the other end)
- 8 Speed clips
- 8 Speed nuts
- Eight 1" self-tapping screws
- Eight 3/4" self-tapping screws
- 2 Machine screws
- Owner's Manual
- Product Registration Card
- On-line registration sheet
- Mounting Template
Customer reviews for Polk EX3560
Loading...
Loading reviews...
Thanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Polk EX3560
Features & specs
General | ||
---|---|---|
Speaker Size | ||
Design | 2-way | |
Tweeter Design | Dome | |
Impedance (Ohms) | 4 | |
Tweeter Composition | Silk | |
Woofer Composition | Polymer-mica | |
Woofer Surround | Butyl rubber | |
Parts Warranty | 1 YEAR | |
Labor Warranty | 1 YEAR | |
Specifications | ||
Sensitivity (1W at 1 meter) | 92 | |
Sensitivity at 2.83 volts | N/A | |
Frequency Response | 50 - 22k Hz | |
Minimum RMS Wattage | 10 | |
Maximum RMS Wattage | 100 | |
Peak Power Handling (Watts) | 300 | |
Top-mount Depth (Inches) | 2 5/16 | |
Bottom-mount Depth (Inches) | N/A | |
Cutout Diameter or Length (inches) | 5 1/4 | |
Mounting Height (Inches) | 0.264 | |
Frame Width | 6.209 | |
Frame Length | 6.209 |
Product Research
Woofer Cone Material: The moisture-resistant mica-filled polymer composite woofer cones produce full, accurate midbass.
Surrounds: The durable butyl rubber surrounds increase speaker life and improve bass response.
Tweeter Dome Material: Each 1" tweeter is made with a silk dome that offers smooth, clear high frequency response.
Elliptical Lens: Each tweeter employs an Elliptical Lens that allows you to focus the high frequencies for pinpoint imaging and clear detail, even from off-axis factory speaker locations. Note: The Elliptical Lenses do not rotate. Instead, they must be aimed before installation.
Tweeter Mounting Options: The tweeters may be surface, angled surface, or flush mounted. They must be installed using one of the three housings.
Flush Mount | Surface Mount | Angled Surface Mount | |
---|---|---|---|
Mounting Depth | 1.015" | 0.609" (screw depth) | 0.609" (screw depth) |
Mounting Height | 0.47" | 1.088" | 1.077" |
Cutout Diameter | 1.851" | NA | NA |
Frame Diameter | 2.209" | 2.036" | 2.097" |
Crossover Dimensions: L=4.708", W=2.714", H=1.419"
2-Way Crossovers: The crossovers feature a 12dB/octave, 4kHz high-pass network for the tweeters and a 12dB/octave, 4kHz low-pass network for the woofers.
Input/Output Connections: The crossover inputs and outputs are gold-plated screw terminals.
Mounting: There are two mounting holes in the base of each crossover.
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...