About the MTX T610X3A
Here's a back seat driver you invite along for the ride! MTX's T610X3A enclosure comes loaded with three Thunder6000 10" woofers, and its trapezoidal shape allows it to fit into many vehicles even tough-to-fit Camaros and Firebirds. The Thunder6000 subs combine an aluminum-coated poly cone, oversized magnet structure, and 4-layer 2" voice coil for powerful bass and serious power handling (up to 750 watts RMS).
The 4-ohm mono design (three 12-ohm subs wired in parallel) maximizes the output capability of your amp. The attractive charcoal carpeting and the stylin' rear Plexiglass window give the enclosure a custom-built appearance.
Details:- three 10" (12-ohm) Thunder6000 woofers wired in parallel for total 4-ohm impedance
- frequency response 46-150 Hz
- power handling 150-750 watts RMS
- peak power handling 1500 watts
- sensitivity 90 dB
- 35-1/8"W x 13-3/8"H x 5-1/8"D(top) x 14-7/16"D (bottom)
- 2-year warranty (on speakers)
What's in the box:
- 1 Hatchback enclosure with three 10" Thunder6000 woofers installed
- Warranty card
- "MTX Audio" sticker
Customer reviews for MTX T610X3A
Loading...
Loading reviews...
Thanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the MTX T610X3A
Features & specs
General | ||
---|---|---|
Woofer Size (inches) | 10 x 3 | |
Speakers Per Box | --- | |
Woofer Material | Mica-filled poly | |
Enclosure Type | Sealed | |
Color | Charcoal | |
Pieces in System | 1 | |
Width (inches) | 35-1/8 | |
Height (inches) | 13-3/8 | |
Depth (inches) | 14-7/16 | |
Connector Type | 5-way post | |
Frequency Response | 46-150 Hz | |
Power Range (Watts RMS) | 750 | |
Maximum Wattage | 1500 | |
Sensitivity | 90 dB | |
Impedance | 4 ohms | |
Parts Warranty | 2 Years | |
Labor Warranty | 2 Years |
Product Research
Features
Angled Front And Back Panels: The enclosure's back panel and front panel are angled at 70 degrees, resulting in a greater depth at the bottom of the enclosure than at the top. The angled design allows the enclosure to fit nicely against the back of the angled rear seat of most cars.
Wiring Configuration: This enclosure is loaded with three 12-ohm 10" woofers and has a single terminal cup with 5-way binding posts. The woofers are wired together in a parallel configuration, resulting in a 4-ohm load.
Mica-filled Polypropylene Cones: Each woofer cone is made of Mica-filled poly with a bright aluminum finish and 8 stiffening ribs for improved cone stiffness and higher mechanical power handling. Concentric rings are molded into the cone and dust cap surfaces to give them a machined appearance. The "MTX Audio" is embossed on the poly dust caps.
NBR Surrounds: Each woofer is made with a one-piece NBR (Nitrile Butadiene Rubber) surround and gasket combination. When bottom-mounting the woofer, the one-piece surround and gasket make an air-tight seal, to prevent any loss of performance due to air leaks around the woofer. When the woofer is top-mounted, the one-piece surround and gasket combination enhances the overall cosmetic appearance of the woofer. NBR has the added benefit of being resistant to ozone and UV rays for extreme durability.
Oversized Magnet Structure: Each woofer has an oversized (37 oz.) magnet structure, with a 2" voice coil.
Asymmetrical Linear Drive: This system improves linearity and permits high output with low distortion.
Spider Plateau Venting: Heat from the voice coil is vented through metal-mesh covered vents that surround the back of the spider.
5-way Binding Posts: The enclosure has one set of gold-plated 5-way binding posts that will accept bare wire, pin connectors, spade lugs, banana plugs, and dual banana plugs.
The MTX T610X3A replaces these items
MTX T610x3
- Hatchback-style sealed enclosure with three injected molded poly woofers
- frequency response 46-150 Hz
- power handling 150-750 watts RMS
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...