Features
Controls
Connections

Features

Mono-Channel Subwoofer Amplifier: The JL Audio G1700 is a class D monoblock subwoofer amplifier that is  rated at 350 Watts RMS x 1-channel in 4 ohm at 20 to 250Hz with a signal-to-noise-ratio of  90 dB and a total harmonic distortion of 1% while receiving 14.4 Volts. The amplifier is rated at 700 Watt RMS x 1-channel in a 2 ohm load at 14.4 Volts. While receiving 12.5 Volts the amplifier is rated at 250 Watts RMS x 1-channel in 4 ohm with a total harmonic distortion of 1% or 500 Watts RMS x 1-channel in 2 ohm. The JL Audio subwoofer amplifier's frequency response is limited to the range of 10-250Hz and is not designed for driving midrange speakers or tweeters. Every aspect of the amplifier's operation has been optimized for low-frequency amplification.

Class D Circuitry: This JL Audio Class D subwoofer amplifier utilizes a proprietary Class D circuit. JL Audio's Patented Class D output circuit utilizes a discrete control section and a unique feedback loop design that results in outstanding power regulation and a damping factor greater than 500 at 4 ohms (>250 at 2 ohms). This is vastly higher than other Class D designs and also higher than most Class A/B amplifiers. The benefit of this exclusive JL Audio technology is tight, clean bass reproduction with the efficiency advantage of Class D amplification.

Differential-Balance Inputs: The JL Audio amplifier features differential-balanced input architecture to effectively control noise and ensure compatibility with a wide variety of source units, including many OEM systems. Without resorting to line output converters, you can directly connect most OEM source units to the JL Audio amplifier without creating any noise or compatibility issues. Unlike conventional single-ended inputs, the differential-balanced design does not connect one side of the audio signal to chassis ground.  This eliminates any voltage sensitivity between one input terminal and ground and greatly reduces the incidence of alternator whine in a typical car audio installation. The G1700 amplifier provides range switching on each of its inputs via the "Input Voltage" switch. This permits connection to a wide range of source voltages while retaining excellent sensitivity setting precision.

Preamp Outputs: The G-Series amplifier features one pair of preamp outputs that make connecting multiple amplifiers simple. The preamp pass-through outputs are configured in parallel with the amp inputs. The signal present at these outputs is identical to the signal at the amp inputs and is unaffected by any on-board processing.

Advanced Rollback Protection: Should an G-Series amplifier ever overheat, its intelligent, unregulated power supply reacts by limiting available peak voltage until the amplifier returns to a safe temperature range. Likewise, if an impedance lower than optimal for the amplifier is present at the outputs, the G-Series amplifier will roll back peak voltage to protect itself without shutting down.

Protection Circuitry With Status Indicator Lights: There are two status indicator lights on the right side of the amplifier.

• Power (Green): This LED lights green to indicate that the amplifier is turned on and operating normally.
• Protect (Red): The Protection LED lights Red to indicate the amplifier's protection circuitry has been activated to prevent product failure due to a short-circuit or a dangerously low impedance connected to the amplifier's outputs.

Controls

Simplified Gain Setting: The G-Series amplifier makes setting the gain level of the amp via the input sensitivity control very simple. All you need is Digital AC Voltmeter (142TK12V, sold separately) and a Test CD Disc (503CD104, sold separately) with a sine-wave test-tone recorded at 0 dB reference level in the frequency range to be amplified for that set of channels (50 Hz for subwoofer channels, 1 kHz for a midrange application).

Active Crossover: The active crossover sections of the G-Series amplifier offer excellent flexibility and precise tuning. The G1700 features the following crossover adjustments.

• Low Pass Filter: You can select a 12 dB/octave Low Pass or 24 dB/octave Low Pass. You can also turn the amplifier's Low Pass crossover off if you choose to use an external electronic crossover. In the Off mode the amplifier has a frequency range up to 250 Hz.
• Filter Frequency: The filter frequency for the 12dB/octave or 24dB/octave Low Pass crossover can be set from 40 to 200 Hz.

Bass Controls: The bass boost circuit of the G-Series amplifier offers the following controls.

• Bass Boost: The amplifier is equipped with a fixed +6dB, 48 Hz Bass Boost.
• Remote Bass Port: The amplifier is equipped with a connection for a wired Remote Bass Control (136RBC1, sold separately) that allows fully variable boost control (0-12dB) from the front of your vehicle.

Connections

Left Side Of Amplifier:

• Power and Ground: The JL Audio amplifier's set-screw Power and Ground connections are designed to accept 8 to 4 AWG power wire.
• Remote Turn-On: The G-Series amplifier's set-screw turn-on lead will accept 18 to 12 AWG  wire.
• Speaker Outputs: The G1700 amplifier's set-screw speaker terminals will accept 16 to 8 AWG speaker wire.

Right Side Of Amplifier:

• Preamp Inputs: The amplifier features one set of differential-balanced RCA jack inputs. The amplifier's input level can be set to Low (200mV-2V RMS) when connecting the amplifier to a low-level preamp signal or set to High (800mV-8V RMS) when connecting the amplifier to a high-level speaker signal.
• Preamp Outputs: The amplifier also features one set of pass-through preamp outputs so you can send an unaltered audio signal to another amplifier in your system.
• Remote Bass Port: The amplifier is equipped with a connection for a wired Remote Bass Control (136RBC1, sold separately).