About the Kenwood 500-watt Dual 10" Bass Package
Add some bass to your ride
Add some bass to your ride
This Kenwood bass package includes a 500-watt mono amplifier, two 10" subwoofers, and a sealed dual 10" enclosure. Just add some wiring for a complete sub system that'll bring the thrill of powerful bass to your vehicle.
KAC-5001PS mono sub amp
Kenwood's KAC-5001PS mono amp punches out up to 500 watts RMS to the two 10" subwoofers. A rugged cast heatsink keeps this amp running at optimal temperatures, even when you're pushing your system hard. A built-in low-pass filter lets you adjust the output so you'll get the best sound possible from these subs in the Sound Ordnance enclosure. And you can dial in up to 18 dB of bass boost if you want to fatten up the thump.
All of the amp's controls are on the same side for easy access.
Two KFC-W2513PS 10" subwoofers
Each 4-ohm KFC-W2513PS Performance Series 10" sub handles up to 300 watts RMS, so two of them will work well with the KAC-5001PS. The sub's diamond-array patterned cone resists flexing, for strong and clean bass notes. A tough rubber surround accommodates the extra-long cone excursion that pumps up the volume. And a dual vent cooling system makes sure the sub keeps going strong, even during long, loud jams.
Sound Ordnance dual 10" sealed enclosure
Sound Ordnance's rugged Bass Bunker BB102-75S sealed enclosure holds two 10" subwoofers, offering an internal volume of 0.76 cubic feet per chamber. This unloaded enclosure features high-grade, medium-density fiberboard construction, with sealed inner braces that help combat resonance by reducing vibrations.
Installation Note: Make sure you set the amp's gain controls properly to avoid distortion. This diagram shows you how to wire up the sub(s) in this package.
Product highlights:
- package includes KAC-5001PS amp, two KFC-W2513PS 10" subs, and Sound Ordnance sealed dual 10" enclosure
KAC-5001PS mono subwoofer amplifier
- 300 watts RMS x 1 at 4 ohms (500 watts x 1 at 2 ohms)
- variable low-pass filter (50-200 Hz, 24 dB/octave)
- variable bass boost (0-18 dB at 40 Hz)
- preamp inputs
- fuse rating: 30A x 2
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 9-13/16"W x 2-1/4"H x 7-9/16"D
- warranty: 1 year
KFC-W2513PS 10" 4-ohm subwoofers (pair)
- diamond-array polypropylene woofer cone with rubber surround
- power range: 50-300 watts RMS
- frequency response: 39-300 Hz
- sensitivity: 82 dB
- warranty: 1 year
BB102-75S sealed enclosure
- hatchback style enclosure for two 10" subwoofers
- 5/8" MDF (medium-density fiberboard) with black carpet covering
- dimensions: 26-3/4"W x 13-7/16"H x 11-5/8"D1 x 8-1/2"D2
- warranty: 1 year
What's in the box:
- This subwoofer package contains four individually packaged items: a Kenwood KAC-5001PS amplifier/ two Kenwood KFC-W2513PS subwoofers/ and a Sound Ordnance BB102-75S dual 10" subwoofer enclosure
- The KAC-5001PS Box includes:
- Mono subwoofer amplifier
- 2 End caps (installed)
- Two 30-amp fuses (installed)
- 2.5mm Allen wrench
- Four 5/8" Self-tapping screws
- Instruction manual (English/ French/ Spanish)
- Warranty information
- Each KFC-W2513PS Box includes:
- One 10" Single 4-ohm voice coil woofer
- Plastic trim ring
- Eight 1-1/4" Self-tapping screws
- Adhesive backed foam gasket
- Cardboard template
- Instruction manual (English/ French/ Spanish/ Portuguese)
- Warranty information
- The BB102-75S Box includes:
- Hatchback-style enclosure for two 10" subwoofers
Customer reviews for Kenwood 500-watt Dual 10" Bass Package
Loading...
Loading reviews...
Thanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kenwood 500-watt Dual 10" Bass Package
Product Research
KAC-5001PS Amplifier
KFC-W2513PS Subwoofers
BB102-75S Enclosure
KAC-5001PS Amplifier
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). Using CEA-2006 criteria, the Kenwood KAC-5001PS is rated at 300 Watts RMS x 1 channel with an 83 dBA signal to noise ratio.
Specifications: The manual also lists these non CEA-2006 compliant specifications:
- Power: 500 watts x 1-channel (into 2Ω, at 100 Hz, no more than 1.0% THD, 14.4 volts)
- Signal to Noise Ratio: 100 dB (at rated power)
Mono-Power Amp Design: The KAC-5001PS is designed with specific features to power your subwoofers with a frequency range between 20 and 200 Hz. This amplifier is not designed to power a full-range speaker.
Class D Amplifier Design: The amplifier design is Class D, which uses digital switching power supplies. The result is much higher efficiency (less heat generated) than Class AB.
Low-Pass Filter: The built-in 24 dB/octave low-pass filter is continuously variable from 50 to 200 Hz. The crossover is always engaged (it cannot be bypassed).
Bass Boost: The bass boost circuit is centered at 40 Hz; boost is variable from 0 to +18 dB.
Controls:
- Input Sensitivity: 200mV-5V; continuously variable
- Low-Pass Frequency: 50-200 Hz; continuously variable
- Bass Boost: 0-18 dB; continuously variable
Inputs and Outputs:
- Signal Input: one pair of RCA inputs
- Power: screw terminal; accommodates spade connector up to 0.55" wide
- Ground: screw terminal; accommodates spade connector up to 0.55" wide
- Remote Turn-on: screw terminal; accommodates spade connector up to 0.335" wide
- Speaker Output: one pair of screw terminals; accommodates spade connector up to 0.335" wide
- Fuses: two 30 amp ATO fuses
Dimensions:
- Width: 9.782"
- Height: 2.2"
- Depth: 7.552"
KFC-W2513PS Subwoofers
Cone: The KFC-W2513PS uses a polypropylene cone and rubber surround for added durability.
Heat Transfer System: A dual ventilation system design helps keep the motor structure cool, improving power handling and longevity.
Long Stroke Design: The pole piece has been extended to provide a more linear magnetic field for woofer operation. This lowers distortion and provides the woofer with better low frequency response.
Double Stacked Magnet: The stacked magnet assembly is used to create a powerful linear motor with increased excursion capability for superior bass output.
Spring Terminals: The spring post terminals on one side of the woofer connect to your amplifier's wiring. The posts will accept pin connectors, single banana plugs, or bare wire up to 10 gauge.
BB102-75S Enclosure
Materials: The Sound Ordnance BB102-75S Bass Bunker is an unloaded, hatchback-style sealed enclosure for dual 10" subwoofers. It is constructed of 5/8" MDF (medium-density fiberboard), covered in black carpet.
Internal Box Volume: The enclosure has two separate chambers, each with 0.75 cubic feet of airspace.
Terminals: The BB102-75S is equipped with two pair of spring-post speaker terminals, one for each chamber, mounted in the rear panel. The spring terminals will accept bare wire, pin connectors, and single banana plugs, but are spaced too far apart for standard (3/4") dual banana plugs. Inside the enclosure, each set of terminals has an attached 18" length of speaker wire for connecting the subwoofer.
Brackets: Brackets for securing the enclosure to your vehicle are recommended.
Dimensions:
- Width: 26.8125"
- Height: 13.5625"
- Depth1: 11.625" (at the base)
- Depth2: 8.625" (at the top)
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...