About the JL Audio JX250/1D
Lots of power from a very small box
Lots of power from a very small box
JL Audio's JX250/1D mono amplifier will power your subwoofer with up to 250 watts RMS, so you can experience powerful bass in your music. A variable low-pass filter and bass boost help you tune your sub to sound its best in your system. An optional remote level control lets you turn the sub up or down from the front seat.
Compact, but beefy
You know you're holding a serious piece of sound equipment when you feel the heft of this tiny JX amp. JL Audio built it with sturdy, high-grade parts that ensure excellent heat management, provide high current flow, and deliver stable performance in almost any situation. You won't find blinking lights or meters on the outside of these amps, but you will find oversized output transistors and rugged MOSFET power supplies inside. The high-mass aluminum heatsink keeps things cool enough to virtually eliminate thermal shut-downs.
Product highlights:
- mono subwoofer amplifier
- 160 watts RMS x 1 at 4 ohms (250 watts RMS x 1 at 2 ohms)
- Class D amplifier design
- frequency response: 10-150 Hz
- variable low-pass filter (50-200 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- optional wired remote level control
- preamp inputs and outputs
- speaker-level inputs
- 8-gauge power and ground leads and a 30-amp fuse recommended — wiring and hardware not included with amplifier
- no onboard fuses — when installing multiple amps in a system, an additional 30-amp in-line fuse between the distribution block and the amplifier is recommended
- 7-7/8"W x 2-1/8"H x 7-11/16"D
- warranty: 2 years
- MFR # 99402
What's in the box:
JL Audio JX250/1D owner's manual
- Monoblock subwoofer amplifier
- 10" Speaker-level harness
- 4 Mounting screws (M4 x 18mm)
- 4 Flat washers
- 2.5mm Allen wrench
- Owner's Manual (En/ Ger/ Sp/ Fr)
Customer reviews for JL Audio JX250/1D
Loading...
Loading reviews...
Average review:
5.0 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the JL Audio JX250/1D
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
160 x 1 |
|
Peak Power Output (Watts x Channels) | --- | |
Power at 2 Ohms (Watts x Channels) | 250 x 1 | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 10-150 Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 97 dB | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-200 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/octave | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 45 Hz | |
Fan Cooled | No | |
Fuse Rating | 30 | |
Speaker Level Inputs | --- | |
Preamp Outputs | 1 pair | |
Width (inches) | 7-13/16 | |
Height (inches) | 2-1/8 | |
Depth (inches) | 7-11/16 | |
Parts Warranty | 2 Years | |
Labor Warranty | 2 Years |
Product Research
Features
Monoblock Amplifier: The JL Audio JX250/1D monoblock subwoofer amplifier that has been optimized for low-frequency (10-150 Hz) amplification of connected subwoofers.
Class D Amplifier Circuit: The JX250/1D employs an advanced Class D switching design that allows it to produce 160 watts of clean subwoofer power while drawing significantly less current from your electrical system and generating less heat than a conventional Class A/B or Class B design.
MOSFET Switching Power Supply: The JL Audio JX series monoblock amplifier employs a rugged MOSFET power supply for outstanding reliability and operational stability.
Amplifier Ratings:
JX250/1D Amplifier Specifications | Ohms | Watts |
---|---|---|
Rated Continuous (RMS) Power @ 14.4V (10-150Hz, 90dB S/N, 1% THD+N) | 4Ω | 160 |
3Ω | 200 | |
2Ω | 250 | |
Rated Continuous (RMS) Power @ 12.5V (10-150Hz, 90dB S/N, 1% THD+N) | 4Ω | 125 |
3Ω | 160 | |
2Ω | 220 |
High-Mass Heat Sink: A heavy extruded aluminum heat sink is designed to keep the JX250/1D in a comfortable thermal range during demanding operation. This high-mass, extruded heat sink removes heat from the amplifier circuitry, extending high-power operation. This improves reliability and reduces the frequency of thermally related shut-down event.
Protection Circuitry: The JX250/1D's protection circuitry automatically shuts the amplifier down if thermal limits are exceeded, or a short-circuit is detected in the speaker wiring.
Status Indicator Lights: There are two status indicator lights on the right side of the amplifier.
- Power (Green): This LED lights green to indicate that the amplifier is turned on and operating normally.
- Protect (Red): The Protection LED lights red to indicate the amplifier's protection circuitry has been activated to prevent product failure due to thermal overload, a short-circuit, or a dangerously low impedance connected to the amplifier's outputs.
Controls
Input Sensitivity: The Input Sensitivity Control is used to match your source unit's output voltage to the input stage of the amplifier for maximum clean output:
- Low-Level Input Range: 200mV-4V (RMS)
- High-Level Input Range: 2V-10V (RMS)
Low Pass Crossover: The JL Audio JX250/1D monoblock amplifier is equipped with a 12dB/octave low-pass filter with variable frequency selection from 50 to 200Hz. The low-pass filter is not defeatable.
Bass Boost: The amplifier is equipped with a variable bass boost from 0 to +12dB at 45Hz.
Remote Level Control: The JX250/1D is equipped with an RJ-25 connection for an optional wired RBC-1 Remote Level Control (sold separately) that allows volume level adjustment of the amplifier from the front of your vehicle.
Connections
Power/Ground/Turn-On Terminals: The monoblock amplifier features set-screw terminals for the power, ground, and remote turn-on connections. A 2.5mm hex-wrench is supplied for tightening/loosening the set-screws.
- Power and Ground: The JL Audio amplifier's set-screw Power and Ground connections are designed to accept 8 to 4 AWG power wire. JL Audio recommends 8 gauge power and ground wires.
- Remote Turn-On: The JL Audio JX series amplifier's set-screw turn-on lead will accept 18 to 8 AWG wire. 18-gauge wire is more than adequate for the remote turn-on connection.
Speaker Output Terminals: The JL Audio JX250/1D features four set-screw speaker terminals for an easy parallel subwoofer connection. The monoblock amplifier's four set-screw speaker terminals will accept 16 to 8 AWG speaker wire. A 2.5mm hex-wrench is supplied for tightening/loosening the set-screws.
Preamp Inputs: The monoblock amplifier features one set of stereo RCA input jacks. The amplifier features a dedicated Input Sensitivity gain control for these inputs. These controls are designed to match the input sensitivity of the JX250/1D to the specific signal source that is feeding it. The amplifier's low-level input can be set between 200mV-4V RMS.
Speaker Level Inputs: The JL Audio JX250/1D also accepts speaker level signals, including those from factory systems (without the need for a line-output converter), via the supplied 10" speaker-level harness. The amplifier's high-level input can be set between 2V-10V RMS.
Preamp Outputs: The JX250/1D incorporates a pass-through preamp output sections, so that additional amplifiers can easily be connected to the same signal feeding the monoblock amplifier. The preamp output signal is buffered to prevent noise.
The JL Audio JX250/1D replaces these items
JL Audio JX250/1
- 175 watts RMS x 1 at 4 ohms
- variable low-pass filter (50-200 Hz, 12 dB/octave)
- speaker-level inputs
Loading...
Loading accessories...
Customer Q&A
1 question already asked
Loading...
Loading articles...
I have it connected to a single JL 10" and it pushes it with no problem
Kevin from Fallon, NV