Chat
Contact us
Close contact box
Connect ID #
329 681 686 3
Connect ID #
329 681 686 3
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

All of our representatives are
currently chatting with other customers.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Chat Advisor Image

Your Advisor,

More about me
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

How to install a crossover

Running tweeters, speakers, and subs in an active system

Sound Ordnance P-65C component crossover

Passive Crossovers

Passive crossovers for component speaker systems are very simple to install. They each go between your amplifier and a speaker and do not require a power connection, a turn-on lead, or grounding. You connect the speaker wire coming from your amp to the crossover's input. Then the tweeter gets wired to the tweeter output, and the woofer to the woofer output. That's it. The most challenging part of installing a passive crossover may be where to mount it, but most component crossovers are small enough to fit inside your car door near the woofer's location.

Examples of in-line crossovers

Examples of in-line crossovers

There's another kind of passive crossover, called in-line crossovers, which go between your receiver and amp. They look like little cylinders with RCA connectors on each end and simply plug into your amplifier’s inputs. In-line crossovers each come set to a specific crossover frequency and can’t be adjusted. Another disadvantage of using them is that they react differently to different amplifiers, possibly changing their crossover points unpredictably.

Active Crossovers

Installing an active crossover requires a bit more work. You'll mount your crossover securely, preferably near the amplifiers; give it power, remote turn-on, and ground wiring, like the amps have; and get signal from the receiver and send it to the amps. Once you've done the work, however, you'll gain new control over your music, being able to tune your sound system so that all of the speakers can give you their best performance.

Finding the right spot

You'll want to put your crossover in a location that won't take up too much space in your vehicle, but is accessible enough for you to be able to make adjustments. Usually, you'll just make the initial adjustments to fine-tune the sound and then leave it. But sometimes, you may get into the mood to just tweak your system or give it a different sound for the day. You need to securely mount your crossover so it won't become a flying liability in the event of an auto accident.

Audio Control DQXS and  a Boston GT-50

Audio Control DQXS 4-way crossover with 6-channel EQ (left) getting mounted next to a Boston GT-50 5-channel amp

Do not bolt your crossover directly to metal — that's inviting noise problems, like ground loops which hum or buzz. You could use rubber grommets around the mounting screws to isolate the case. Or you could mount the crossover on a wooden board and attach that to the car body. Some people even mount their crossover and amps on the same board, for convenience. A crossover can actually go anywhere between the receiver and the amp, but most people mount theirs near their amp, making it easier for connections and for future system expansion.

Wiring for power

You'll need to provide 12-volt power from your car battery to operate the crossover just as you would to power your amp. The power and ground wiring for your crossover do not have to be the heavy-gauge stuff that you use for your amp — typically wire as thin as 18-gauge wire will be fine. A distribution block is a good way to get power for your crossover via the same main power cable as the amp uses. You'll also need a solid, noise-free grounding point — it's best to ground your crossover at the same place as your amp. Make sure the grounds get attached tightly to the metal chassis of your vehicle, with all the dirt and paint removed where contact is made.

As for the turn-on lead, you can usually tie it into the turn-on lead for your amps. However, a receiver's turn-on circuit has a limited capacity and could fail if there're three or more devices to be turned on. If that's the case, you'll need a relay, that'll get triggered by the turn-on circuit but get its 12-volt power from another source, like the fuse box. If you bought your crossover from Crutchfield and need help with such a relay network, you can call our tech support department for free advice (please have your invoice handy).

Signal wiring

You get the input for your crossover via RCA patch cables from your receiver. If your receiver doesn't have RCA outputs, you can use a crossover that accepts speaker-level signals for inputs. Or, you can get a line output converter to step the speaker-level signal down to preamp level. Lastly, you run more patch cables from the crossover outputs to the amplifier inputs — highs to the tweeter amp, mids to the woofer amp, and bass to the subwoofer amp, for example

Make sure the patch cords supplying the musical signal to the crossover and amplifier are kept well away from potential sources of noise, such as the amp's power and ground cables, the vehicle's brake light wires, or rear window defroster wires.

Kicker KX3 3-way crossover

Kicker KX3 3-way crossover

Crossover points

Crossover points are the frequency settings of a crossover that represent the points in each output band where the signal is attenuated, turned down, by one-half — a 3 dB drop in power. The intention is, that at each crossover frequency, two adjacent drivers (tweeters, speakers, or subs) are playing the note at one-half power — so the result is full power at each crossover point.

The crossover points you choose ultimately depend on the frequency response of each component driver in your speaker system. Check out the frequency response specifications of each of your drivers and use those frequencies as preliminary crossover points. If you can't find any such specifications, start with 100 Hz as the crossover point between your subwoofer and mid-bass drivers, and 2,000 Hz for the midrange-to-tweeter transition point.

Adjusting frequencies

Unlike the following tune-up tips that take into consideration your music's tone and volume along its entire spectrum, you adjust crossover frequencies to eliminate the distortions a driver will put out when it tries to reproduce notes it can't play well, at the extremes of its frequency response. So, for instance, if you hear your mid-bass/midrange driver distorting on low notes, you adjust its crossover point higher, so it won't even try to play those notes. The same goes for the midrange/tweeter crossover point — you move the crossover point to eliminate distortion — higher to clean up the tweeter's sound, lower for midrange clarity.

Kicker Front Row signal processor

Kicker Front Row signal processor

Now you get to tune your system

The first objective, in setting up a crossover, is to end up with each band of frequencies — for the tweeters, midrange speakers, and subwoofer, for example — playing at the same volume. Next, you apply the EQ curves and other tone adjustments you like in your music. Then, you do it all again, re-setting the crossover to compensate for the equalization adjustments. Some people even tweak the EQ again after that, and on and on, until it sounds perfect to them.

You start off by playing familiar music with all the tone and EQ controls off or set flat and the amp gains down low. All crossovers are different, but you can use the following as a general guide for setting a 3-way crossover:

  1. Find the top level at which your receiver plays your music cleanly. Turn up the volume until music distorts, then turn it back a little.
  2. Set the input sensitivity of the crossover, if it has it. Crossovers with this feature will also have clip indicator lights that help you set this control.
  3. Set the level for each output so they play evenly.
  4.  Set the gain for each pair of amplifier channels. Turn it up until the music distorts, then turn it back a little.
  5. Re-set the crossover output levels to balance the highs, mids, and lows playing from each component. Try to make the system's total response flat— high notes, mid notes, and low notes all playing at the same volume.
  6. Re-set the amp gains, to compensate for any crossover output adjustments.
  7. Re-set crossover output levels again.
  8. Apply EQ or tone adjustments at the receiver. Adjust every available control and /or boost to allow your music to sound its best. Turn on the bass boost, if you use one.
  9. Because you've added equalization, you'll have to slightly re-set the crossover and amp gains again. Find the top level at which your receiver plays music cleanly. Turn up the volume until the music distorts, then turn it back a little.
  10. Re-set the input sensitivity of the crossover, if it has it.
  11. Adjust the level for each crossover output to blend them together smoothly.
  12.  Set the gain for each pair of amplifier channels. Turn it up until the music distorts, then turn it back a little.
  13. Re-set the crossover output levels to balance the highs, mids, and lows playing from each component. This time, your goal is to make it sound great, not flat.
  14. Adjust the amp gains, to compensate for any crossover output adjustments.
  15. Adjust crossover output levels again, if necessary.
  16. Adjust the tone at your receiver again, to allow your music to sound its best, and enjoy.
 
Audio Control 2XS 2-way crossover

Audio Control 2XS 2-way crossover

  • Edgar Rodriguez from Inglewood

    Posted on 3/24/2021

    Hello just bought jbl 960c and jbl gto midrange my question is can I get speaker input from anywhere from my vehicle to supply it to the crossover does it matter it is from the rear factory harness or the front factory speaker harness

    Commenter image

    Buck Pomerantz from Crutchfield

    on 3/24/2021

    Edgar, Use the factory wiring of the position each new speaker is going - front speakers to front wiring; rear speakers to rear wiring.
  • Sly from Honolulu

    Posted on 3/16/2021

    I bought the JBL 601C component speaker for my Honda Civic and it came with woofers, tweeters(with wire attached), crossovers, speaker harness, mounting brackets, and the screws. I'm confused on where to connect the wires? Which number(if any) is the right way? 1)-woofer>speaker harness>original speaker wire? -Tweeter wire>Tweeter of crossover? Where would I connect the input and woofer part of the crossover? 2)-original speaker wire>speaker harness>input of crossover -tweeter wire>tweeter of crossover -woofer>?(no wire left) >woofer of crossover? It seems like I need extra wires for either of the options that I mentioned above and the tweeter wires seem a bit short. Am I supposed to receive extra wires aside from the tweeter with a wire attached and the speaker harness?

  • Sly from Honolulu

    Posted on 3/16/2021

    I bought the JBL 601C component speaker for my Honda Civic and it came with woofers, tweeters(with wire attached), crossovers, speaker harness, mounting brackets, and the screws. I'm confused on where to connect the wires? Am I supposed to connect the woofer>speaker harness>original speaker wire? Tweeter wire>crossover? But where would I connect the input and woofer part of the crossover? Am I missing wires or something?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 3/31/2021

    Sly, The wire from the vehicle's amp or receiver goes to the crossover's input. The tweeter goes to the crossover's tweeter output, and the woofer connects to the woofer output. If you need some more hook-up wire, give us a call so an Advisor can get some out to you as soon as possible.
  • jim kappesser from Syracuse

    Posted on 1/18/2021

    I came upon the below statement while searching w/ Google for active crossover design: "How do you wire an active crossover? They each go between your amplifier and a speaker and do not require a power connection, a turn-on lead, or grounding. You connect the speaker wire coming from your amp to the crossover's input. Then the tweeter gets wired to the tweeter output, and the woofer to the woofer output. That's it. How to Install a Crossover - [link removed] An obvious description of the installation of a passive crossover. Just thought I'd let you know the Google search is crediting Crutchfield with this "false" info. Great article above, Thanks...

  • crazyhatch from San Jose

    Posted on 1/7/2021

    Hi If I choose to use a electronic crossover, should I still attach the passive one of the component set? or just wiring them directly to the amp?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 1/12/2021

    Crazy, An electronic, active crossover takes full-range signals from the receiver, divides them into highs and lows, and sends them on to the high and low amplifiers. No need for any passive crossovers.
  • Giorgi from Quimper

    Posted on 7/14/2020

    I connect my tweeter and back door woofers to crossover now i do not know where should i connect input cables which coming from crossover to ampli , can you tell me where is its place ?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 7/16/2020

    Giorgi, A crossover's input usually comes from an amplifier's speaker output.
  • Moses Smith

    Posted on 7/11/2020

    Hi I have ordered some components and the mid woofers have 4 terminals so would I take both the + and wire them both to the positive crossover connection and visa versus with the - ?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 7/13/2020

    Moses, Without knowing precisely what components you're referring to, we can't help you with advice. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you.
  • Rene Torres from Boston

    Posted on 6/18/2020

    Can you install regular crossovers on compression Drivers Speaker ? Or will that mess them up

    Commenter image

    Buck Pomerantz from Crutchfield

    on 6/19/2020

    Rene, I don't know about being "regular" but compression drivers are usually found in PA tweeters, and do need a crossover to operate safely.
  • Dustin from La

    Posted on 6/10/2020

    How do I get my Sony xav-ax1000 connected to the crossover for my infinity kappa 60.11cs?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 6/10/2020

    Dustin, Presumably your aftermarket receiver is correctly plugged into the factory harness. Use the factory speaker wiring near each speaker for the crossovers' inputs.
  • Audley Dennis from Portsmouth

    Posted on 10/6/2019

    My name how to install 2 DJ amp to a 2 way crossover?

    Commenter image

    Buck Pomerantz from Crutchfield

    on 10/7/2019

    Audley, You should never connect two amplifier outputs to the same device - they could damage each other.

Looking for
car audio crossovers?

Shop our selection

Find what Fits your vehicle