Contact us
Close contact box
Connect ID #
329 681 686 3
Connect ID #
329 681 686 3
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Chat Advisor Image

Your Advisor,

More about me
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Review: Rockford Fosgate C.L.E.A.N. amplifier gain-setting system

Properly setting an amplifier's gain level in seconds

Rockford Fosgate Punch P400X4

Rockford Fosgate Punch P400X4

Setting the gain of a car amplifier properly is very important to ensuring your music will sound as distortion-free and powerful as possible. For many, setting an amp’s gain can be technically difficult and often incomprehensible. Rockford Fosgate has come up with a method that allows you to set the gain of their new Punch amplifiers quickly and accurately. With their C.L.E.A.N. ("Calibrated Level Eliminates Audible Noise") system, it’s as easy as playing an audio track and adjusting a couple of volume knobs.

Testing a Punch P400X4

Rockford Fosgate rates the P400X4 4-channel amp at 50 watts RMS per channel at 4 ohms and 100 watts per channel at 2 ohms. My first impression of this amp, when I got it out of its box, was that it's very small and very heavy for its size. The chassis is one solid aluminum heatsink. The connections are beefy — I could really crank down on the screws holding the power and speaker wires. This is important for an amp because loose connections often cause problems in car audio.

Out of the box

The amplifier comes with a small bag of mounting screws and an Allen wrench tool, along with a certificate of performance, an illustrated quick-start guide sheet, and a CD loaded with 27 audio test tracks and the complete owner's guide as a PDF file (multiple languages). One side of the illustrated guide shows how to hook up the amp and the other shows how to set the gain. The certificate indicated that the amp I was working with had put out an average of 142 watts per channel at 2 ohms when tested at the factory — that's about 40% higher than the rated specifications, so a customer's experience will most likely exceed their expectation.

Setting up

A small problem I encountered was that the hex-head Allen wrench tool that came with the amp didn't fit the panel screws, preventing me from opening the panel to make the setup adjustments. A few seconds with an emery board fixed it, taking off the little burr of metal at the tip of the tool. All the connections are on one side of the amp, which simplifies the wiring and makes installations easier to keep neat. It was a bit disconcerting that I had to reach my hand just over the power wires to make the gain and other adjustments, but I was confident that the wires were tightly in their place and posed no threat of shock to me.

Turn the gain up until the light turns blue

I turned up the gain until the light turned blue

Setting the gain

It took me less time to do it than it will to tell about it. The illustrated guide shows 10 steps, but it was simpler to follow than even that. With the receiver's tone controls set flat, I played Track 7, a 0 dB 1000 Hertz sine wave. I turned up the receiver's volume to full, and checked the input clip light on the P400X4. The CD player I used did not clip, even at full volume. If it had, I would have had to turn the receiver's volume down until the clip light went out. So far so good. I turned up the gain adjustment for the front channels until the output clip light turned blue, overshot to red, then back down to blue. I repeated that for the rear channels. I was done in well less than 60 seconds, the play-time of the test track.

For non-CD media receivers

Rockford Fosgate's setup test tones are also available as MP3 downloads from Amazon On Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc." (Punch amps and the 3sixty.3 use the same test tone tracks for setup.) Another way to utilize the C.L.E.A.N. setup system would be to, first, copy the tracks you wish to use into a computer, and then copy them to a thumb drive, so you could play them from your media receiver. For the most accurate and consistent results, be sure to download, rip, and copy your test tones at the highest possible resolution or fidelity.

Checking up on it

The lights on the amp indicated that it was set up correctly — but was it? I next connected an oscilloscope and a volt meter to the amp's output and repeated the setup procedures while keeping an eye on the waveform and RMS voltage. Sure enough, the 1000 Hz signal never clipped when the receiver was maxed, but just started to flatten at the top when the blue light came on, and was obviously clipped when the light turned red. Easing it back to blue, I read that the amp was putting out 19.5 volts RMS. That translated to 190 watts at 2 ohms, almost 50 watts more than the certificate specified.

The amp seemed to do better because no speaker was connected

I measured the amplifier working without a load, which would have lowered that reading to the expected 16.9 VRMS, which is 142 watts at 2 ohms. The load, in this case, would have been a speaker, and even a 50-watt 1000 Hz sine wave through a speaker is extremely loud, annoying, and dangerous to hearing, so I didn't use one. The clip lights accurately indicated what was going on with the signal, so I'll believe Rockford Fosgate's certificate of performance.

Conclusion: It works as advertised

If you follow the simple directions, you can properly set the gain of one of these Punch amps with the C.L.E.A.N. system in seconds. This guarantees that the maximum clean signal coming out of your receiver will result in the cleanest and most powerful output from this Rockford Fosgate amplifier. Sounds good too, and works for me.

This video from Rockford Fosgate shows how quick and easy gain-setting is with their C.L.E.A.N. system:

In this video, he shows how the optional remote clip indicator can help you monitor the signal from the front seat:

Try it for yourself

Rockford Fosgate makes a few models of Punch amplifiers, all of which feature the C.L.E.A.N. gain-setting system:

P300X1 mono subwoofer amplifier, 300 watts RMS x 1 at 2 ohms

P500X1bd mono subwoofer amplifier, 500 watts RMS x 1 at 1 ohms

P1000X1bd mono subwoofer amplifier, 1,000 watts RMS x 1 at 1 ohms

P300X2 2-channel car amplifier, 100 watts RMS x 2

P500X2 2-channel car amplifier, 150 watts RMS x 2

P1000X2 2-channel car amplifier, 300 watts RMS x 2

P400X4 4-channel car amplifier, 50 watts RMS x 4

P600X4 4-channel car amplifier, 75 watts RMS x 4

P1000X5 5-channel car amplifier, 75 watts RMS x 4 plus 500 watts RMS x 1 at 1 ohm

  • Dan from Winchester

    Posted on 5/26/2021

    Buck, How do I know which frequency to set the front and rear channels to on the amp? I just had a shop install a pair of mpk 165.3s (front channel), mpk 165.3s (rear channel), and a p3d4-10 amp. Also, what about the Punch EQ? I'm looking to get optimal sound for a fairly high grade system. Thanks!

    Commenter image

    Buck Pomerantz from Crutchfield

    on 5/28/2021

    Dan, Your installer should have already set this all up, so you may want to check in with them before proceeding. Even without knowing what amplifier you have, the principle's the same. Start by setting high-pass filters to around 80-100 Hz for speakers and the low-pass filter for subs also to around 80-100 Hz. Then tweak 'til it sounds good to you. The same for the Punch EQ - adjust to taste.
  • Lamar D Tookes from New Castle

    Posted on 8/5/2018

    Is the clip light normal with songs that have a lot of base ? Can i allow it to play as long as it dont turn to red and blue

    Commenter image

    Buck Pomerantz from Crutchfield

    on 8/6/2018

    Lamar, When an amp indicates that it's clipping, you should turn down its gain until it's not, otherwise it could damage your subs and speakers. For your amp, neither the input nor output LEDs should ever flash red.
  • Commenter image

    Buck Pomerantz from Crutchfield

    Posted on 7/7/2017

    Alec, That CD of test tones will be useful for setting the gain of any amplifier, even ones without the CLEAN system. For subwoofer amplifiers, it's recommended you use the 40 Hz tone, track #5 on the test CD.

  • Aleks from Place

    Posted on 7/7/2017

    Can I use this cd for Power Amps (T500)? Also, what track should I play for subwoofer amp?

  • Commenter image

    Buck Pomerantz from Crutchfield

    Posted on 4/24/2017

    Jason, That amplifier features a NOMAD protection circuit that limits the amp's output when it's connected to a load too low for it to handle. The amp will eventually burn up if you keep it wired that way. If your bass isn't loud enough, get a stronger amplifier.

  • Jason from Lebanon il

    Posted on 4/22/2017

    I have an older model punch 800.2 with a kicker comp r 12 dvc 2 ohm. I had it wired to 4 ohm to match bridging specs on the punch 800.2. I couldn't get any bass without turning gain all the way up. So I dropped the speaker ohm back to 2 and yes got allot more from the sub but I know its not good for the amp. But I still had to turn gains all the way up at 2 ohms bridged and on just a or b channel. Any advice?

  • Commenter image

    Buck Pomerantz from Crutchfield

    Posted on 8/19/2016

    Yamir, The test tones are available as MP3 download from Amazon On Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup). Another thing you can do, to use the C.L.E.A.N. set up system is, first, copy the tracks you wish to use into a computer. Then, copy them to a thumb drive, so you can play them from your media receiver. And thank you for the great question. I've now added the answer to the article for clarification.

  • Yamir from Palm Springs

    Posted on 8/19/2016

    I plan on getting a CD-Less pioneer head unit. Will I still be able to utilize the Clean setup somehow?

  • Commenter image

    Buck Pomerantz from Crutchfield

    Posted on 6/20/2016

    Ryan, There are virtually no benefits in getting a 2-channel amp to drive a subwoofer system. Most 2-channel amps can't drive loads lower than 4 ohms when bridged, and don't have enough power to drive 2 subs. Mono, 1-channel amps are designed to work with a wider range of impedances, and have tone controls and filters specifically made to help reproduce bass.

  • Ryan Roberts from West Richland

    Posted on 6/19/2016

    Looking to downsize from my T500-1ND, and looking at the P500x1bd or the P500x2 for a sub. Is there any real benefit of one over the other? Aside from the ultrasound filter and smaller size with the x1?