About the Dual XIA2460
Dual brings you a powerful, versatile amplifier at an affordable price. The XIA2460 amp delivers 100 watts of continuous power to two channels, or 300 watts into a single channel. Efficient power supplies offer quick response, while the die-cast aluminum heatsinks incorporated into the black casing keep the amp running cooler for extended life.
Add the XIA2460 to your aftermarket stereo with preamp connections, or hook up to your factory radio with the speaker-level inputs. Variable frequency filters send the right signals to your speakers to keep them from reaching for sounds they can't reproduce. A variable bass boost adds extra fullness to the low notes when you need it.
- 2-channel car amplifier
- 100 watts RMS x 2 at 4 ohms (145 watts RMS x 2 at 2 ohms)
- 300 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
- variable high- and low-pass filters
- variable bass boost (0-12 dB at 45 Hz)
- class AB output design
- CEA-2006 compliant
- speaker- and preamp-level inputs
- fuse rating: 40A x 1
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 14-1/2"W x 2-5/8"H x 11-1/4"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # XIA2460
What's in the box:
- 2-Channel amplifier
- 2 Spare fuses (40A and 2A)
- Allen wrench (3mm)
- 4 Self-tapping screws (3/4" length)
- 4 Flat washers
- 12" Speaker level input harness (with 5-pin Molex plug on one end)
- 12" Illuminite harness (to connect to Dual illuminating speakers)
- Installation/Owner's Manual
Thanks for submitting your review
More details on the Dual XIA2460
Features & specs
|RMS Power Output (Watts x Channels)||
100 x 2 |
|Peak Power Output (Watts x Channels)||230 x 2|
|Power at 2 Ohms (Watts x Channels)||145 x 2|
|Bridged Power (Watts x Channels)||300 x 1|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||20-20k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||76 dB|
|Low-Pass Crossover Frequency||40-400 Hz|
|Low-Pass Slope (dB/octave)||12dB/oct|
|High-Pass Crossover Frequency||40-400 Hz|
|High-Pass Slope (dB/octave)||12dB/oct|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||45 Hz|
|Fuse Rating||40 x 1, 2 x 1 (Lights)|
|Speaker Level Inputs||---|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Die-cast Aluminum Heatsink: The Dual XIA2460 amplifier features a die-cast aluminum heatsink for effective heat dissipation.
Illuminite Circuit: The amplifier has a dedicated low current DC output designed to illuminate the lighting elements found in Dual XIN-series speakers. A 4-wire harness is included specifically for this purpose. The circuit is protected by a separate 2-amp fuse. Note: This DC output should not be used to connect to speaker terminals or other items.
Protection Circuits: This amp has three types of protection circuits: reverse polarity, speaker short circuit, and thermal protection. The LED on the left side of the amplifier will glow red to indicate that the amplifier has gone into protection. Under normal conditions, the LED glows green to indicate the amplifier is receiving power.
Built-In Crossover: This amplifier includes a built-in 40-400 Hz, continuously variable crossover. A 3-way switch allows you to configure the crossover for low-pass, high-pass, or full range operation.
Bass Boost: The amp is equipped with an adjustable 0dB to +12dB bass boost at 45 Hz.
Stereo/Bridged Simultaneous Operation: With an optional passive crossover, such as the PAC TM100 (item #127TM100), you can operate a pair of stereo speakers and a subwoofer from 2 channels. This configuration is also known as Tri-mode or Tri-way operation.
Set Screw Terminals: The power, ground, remote turn-on, and speaker output connections feature set-screw terminals that can accept up to 8-gauge bare wire. A 3mm Allen wrench is supplied to tighten/loosen the set screws.