About the JVC KS-AX3002
Here's your chance to put JVC power in your vehicle at a great price. The versatile 2-channel KS-AX3002 amplifier delivers 65 watts RMS per channel to your full-range speakers, bringing new depth and power to your car's audio system. You can also switch the amp to single-channel operation, and drive your subwoofer with 130 watts RMS.
Selectable high- and low-pass filters allow your system to sound its best you can trim low frequencies out of your speakers, or send only low bass to your subwoofer. You'll also find high- and low-level inputs, so you can add this amp to almost any system, even a factory radio.
- 2-channel car amplifier
- 65 watts RMS x 2 at 4 ohms (90 watts RMS x 2 at 2 ohms)
- 130 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
- selectable low-pass (80 Hz) and high-pass (150 Hz) filters (12 dB per octave)
- CEA-2006 compliant
- speaker- and preamp-level inputs
- fuse rating: 25A x 1
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 8-3/8"W x 2"H x 7-3/4"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # KS-AX3002
What's in the box:
- Two-channel amplifier
- 25-amp fuse (installed)
- Speaker input harness
- Four 3/4" Self-tapping screws
- Instructions (English/ French)
- Instructions (Spanish)
- Product registration card/questionnaire
- Warranty information (US)
- Warranty information (Canada)
JVC KS-AX3002 reviews
Thanks for submitting your review
More details on the JVC KS-AX3002
Features & specs
|RMS Power Output (Watts x Channels)||
65 x 2 |
|Peak Power Output (Watts x Channels)||370 x 1|
|Power at 2 Ohms (Watts x Channels)||90 x 2|
|Bridged Power (Watts x Channels)||130 x 1|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||5-50k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||76 dB|
|Low-Pass Crossover Frequency||80 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||150 Hz|
|High-Pass Slope (dB/octave)||12 dB/oct|
|Bass Boost Frequency||N/A|
|Fuse Rating||25 x 1|
|Speaker Level Inputs||Harness|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
CEA-2006 Compliant: The specifications given by JVC for the KS-AX3002 amplifier comply with CEA-2006 Amplifier Power Standards from the CEA (Consumer Electronics Association). All manufacturers who comply with the standard can display the CEA-2006 logo on their product.
Tri-Mode: When using appropriate passive crossovers on all speakers, the KS-AX3002 can power two stereo speakers (4Ω minimum with a high-pass passive crossover) and a single subwoofer (4Ω minimum with a low-pass passive crossover) simultaneously.
LED: There is a green LED on the input panel (left side) of the amp to indicate the power is on.
Internal Crossover: The amplifier's internal crossover can be set to HPF (high-pass filter), LPF (low-pass filter), or Off (full range, the crossover is bypassed). The high-pass crossover point is 150 Hz and the low-pass crossover point is 80 Hz. Both crossover's slope is 12dB/octave.
Power Connections: The power, ground, and remote inputs are on a terminal strip. JVC recommends 8 gauge wire minimum for power and ground, and recommends using ring terminals on the wire. The power and ground terminals are 0.435" wide and the remote terminal is 0.315" wide.
Inputs: The KS-AX3002 offers both line-level and speaker-level inputs. The supplied speaker-level input harness allows you to connect the input to a receiver without preamp outputs, either aftermarket or factory.
Speaker Connections: The speaker outputs are also on the terminal strip. JVC recommends 12-18 gauge speaker wire, and recommends using ring terminals on the wire. The terminals are 0.315" wide.