About the JVC KS-AX4302
Here's your chance to put JVC power in your vehicle at a great price. The powerful 2-channel KS-AX4302 amplifier puts out 100 watts RMS per channel to your full-range speakers, bringing new depth and power to your car audio system. You can also switch the amp to single-channel operation, and drive your subwoofer with 200 watts RMS. A subsonic filter removes ultra-low frequencies, so your amp and speakers don't have to waste energy trying to reproduce sounds that are below the range of human hearing.
The variable high- and low-pass filters allow your system to sound its best you can trim low frequencies out of your speakers, or send only low bass to your subwoofer. If you want to add a little low-end punch, just dial in the variable bass boost at 45 Hz. You'll also find high- and low-level inputs so you can add this amp to almost any system, and preamp outputs give you an easy way to route the signal to a second amp in your system.
- 2-channel car amplifier
- 100 watts RMS x 2 at 4 ohms (100 watts RMS x 2 at 2 ohms)
- 200 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
- variable high- and low-pass filters (50-400 Hz, 12 dB per octave)
- variable bass boost (0-12 dB at 45 Hz)
- subsonic filter (20 Hz)
- MOSFET power supply and outputs
- CEA-2006 compliant
- speaker- and preamp-level inputs
- preamp outputs
- fuse rating: 20A x 2
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 11-13/16"W x 2-1/2"H x 10-7/16"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # KS-AX4302
What's in the box:
- Two-channel amplifier
- Two 20-amp fuses (installed)
- Speaker input harness
- Four 3/4" Self-tapping screws
- 4mm Allen wrench
- 3mm Allen wrench
- Instructions (English/ French)
- Instructions (Spanish)
- Product registration card/questionnaire
- Warranty information (US)
- Warranty information (Canada)
JVC KS-AX4302 reviews
Thanks for submitting your review
More details on the JVC KS-AX4302
Features & specs
|RMS Power Output (Watts x Channels)||
100 x 2 |
|Peak Power Output (Watts x Channels)||600 x 1|
|Power at 2 Ohms (Watts x Channels)||100 x 2|
|Bridged Power (Watts x Channels)||200 x 1|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||5-50k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||80 dB|
|Low-Pass Crossover Frequency||50-400 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||50-400 Hz|
|High-Pass Slope (dB/octave)||12 dB/oct|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||45 Hz|
|Fuse Rating||20 x 2|
|Speaker Level Inputs||Harness|
|Preamp Outputs||1 pair|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
CEA-2006 Compliant: The specifications given by JVC for the KS-AX4302 amplifier comply with CEA-2006 Amplifier Power Standards from the CEA (Consumer Electronics Association). All manufacturers who comply with the standard can display the CEA-2006 logo on their product.
Tri-Mode: When using appropriate passive crossovers on all speakers, the KS-AX4302 can power two stereo speakers (4Ω minimum with a high-pass passive crossover) and a single subwoofer (4Ω minimum with a low-pass passive crossover) simultaneously.
4-Way Protection: The amplifier features a protection circuit that will turn the unit off if any of the following four conditions occur:
- Thermal: the operating temperature of the amp gets too high
- Short Circuit: there is a short circuit on one of the speaker wires
- Overload: the impedance of the connected load is too low
- DC Offset: direct current is detected on the speaker wires
LEDs: A blue LED on the top and a green LED on the right side light to indicate the power is on. A red LED on the right side lights to indicate the protection has engaged.
Internal Crossover: The amplifier's internal crossover can be set to HPF (high-pass filter), LPF (low-pass filter), or Off (full range, the crossover is bypassed). The crossover point is continuously variable from 50 Hz to 400 Hz; the slope is 12dB/octave.
Power Connections: The power, ground, and remote inputs are set screw terminals. JVC recommends 8 gauge wire minimum for power and ground; the power and ground terminals will accept up to 4 gauge bare wire, the remote terminal will accept up to 8 gauge bare wire.
Inputs: The KS-AX4302 offers both line-level and speaker-level inputs. The supplied speaker-level input harness allows you to connect the input to a receiver without preamp outputs, either aftermarket or factory.
Speaker Connections: The speaker outputs are also set screw terminals. JVC recommends 8-18 gauge speaker wire; the terminals will accept up to 8 gauge bare wire.