About the Infinity Kappa Five
Delivers power in style
Delivers power in style
This handsome little black box delivers big power for your whole system and fits almost anywhere in your car. Infinity's Kappa Five 5-channel amplifier can supply four separate speakers with 75 watts RMS each, plus a subwoofer with 350 watts RMS — good news for everyone who likes their music loud. You could also use this amp to power a pair of high-performance speakers with 200 watts RMS each, and a subwoofer with 350 watts RMS.
System tone controls
High- and low-pass filters on the front and rear channels optimize the amp's output for your speakers, increasing the efficiency of the system. For bass, a low-pass filter clears the way for your sub to play clean, powerful bass tones. The amp also features Infinity's Dynamic Bass Optimizer (DBO™) circuitry, which uses a subsonic filter and bass boost to optimize the performance of your sub and enclosure combo.
The Kappa Five can accept low- or speaker-level inputs so it'll work in almost any system — and Infinity includes RCA-to-speaker wire adapters so you'll make the right connections. They also included an electrical anti-rotational locking (E.A.R.L.) ground terminal, which provides a more conductive and secure ground connection for the amplifier. A wired remote lets you control your bass level from the front seat.
Kappa Five input and control panel
- 5-channel car amplifier
- 75 watts RMS x 4 + 200 Watts RMS x 1 at 4 ohms
- 100 watts RMS x 4 + 350 watts RMS x 1 at 2 ohms
- 200 watts RMS x 2 bridged at 4 ohms + 350 watts RMS x 1 at 2 ohms
- Class D amp technology
- variable high- and low-pass filters (32-320 Hz, 12 dB/octave) on front and rear channels
- variable low-pass filter (32-320 Hz, 12 dB/octave) on subwoofer channel
- Dynamic Bass Optimizer on subwoofer channel:
- variable bass boost (0-12 dB)
- variable subsonic filter (10-80 Hz)
- phase switch on subwoofer channel (0, 180 degrees)
- wired remote bass level controller included
- preamp and speaker-level inputs (bare wire to RCA adapters included)
- 1/0-gauge power/ground wire adapter and E.A.R.L ground terminal included
- wiring and hardware not included with amplifier
- 4-gauge power and ground leads recommended
- fuse rating: 30A x 3
- dimensions: 13-1/8"W x 1-3/4"H x 6-15/16"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # KAPPAFIVE
What's in the box:
- 5-Channel amplifier
- Six 30A ATO fuses (3 installed)
- 6 Bare wire-to-RCA adapters
- EARL ground terminal (for 1/0-gauge wire)
- 3 Flat-head screws (Length 1/2")
- Heat shrink tube (Length 1-3/16")
- 4 Mounting screws (Length 2-3/16")
- 1/0-gauge power/ground wire adapter
- Remote bass controller
- 16.5' Remote cable (RJ25 plugs on both ends)
- Owner's Manual
More details on the Infinity Kappa Five
Features & specs
|RMS Power Output (Watts x Channels)||
75 x 4 |
200 x 1
|Peak Power Output (Watts x Channels)||---|
|Power at 2 Ohms (Watts x Channels)||100 x 4|
|Bridged Power (Watts x Channels)||200 x 2|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||15-35k Hz|
|THD at Rated RMS Power||---|
|Signal to Noise Ratio||80 dB|
|Low-Pass Crossover Frequency||32-320 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||32-320 Hz|
|High-Pass Slope (dB/octave)||12 dB/octave|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||N/A|
|Speaker Level Inputs||RCA|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Power Output: The Infinity Kappa Five 5-channel amplifier delivers the following power output:
- 75 watts RMS x 4 + 200 watts RMS x 1 at 4 ohms
- 100 watts RMS x 4 + 350 watts RMS x 1 at 2 ohms
- 200 watts RMS x 2 at 4 ohms bridged
- 2300 watts total peak power
Protection Circuitry: The amplifier features protection circuitry for thermal overload, DC voltage on the audio output, over- or under-voltage (<9V or >16V), and short circuits. The LED on the back panel of the amp glows red if the amp goes into protection mode.
Remote Level Control: The Kappa Five comes with a rotary Remote Level Control module that lets you control the output of the subwoofer channel from a convenient location in the vehicle. A 16.5-foot cable is included.
Gain: The Kappa Five's rotary gain control let you match the amp's input sensitivity to the output of the source unit. The maximum input sensitivity of the amplifier 0.2V for a line-level input, and 2V for speaker-level input. The maximum signal level is 20V for both line and speaker level inputs. There are separate gain controls for the front, rear, and subwoofer channels. A small screwdriver (not included) is required to set the gain.
Input Level: The Input Level switch should be set to match the type of input signal connected to the amplifier. If using line-level connections, select LO. If using speaker-level inputs, select Hi1 or Hi2. Hi2 contains a special circuit designed to fool a factory audio system to detect a speaker connected to its output, and should be used only if Hi1 doesn't work.
Sub Input: The Sub Input switch lets you select the source of the subwoofer channel. If you are connecting a separate subwoofer input from the source unit, you should select "EXT" (External). If you do not have a separate subwoofer input, you can send the signal from the front or rear channels to the subwoofer channel by selecting "INT" (internal).
Crossover: The amp features switchable crossovers for the front, rear, and subwoofer channels. On the front and rear channel crossovers, you can choose LPF (low-pass filter), HPF (high-pass filter), or Full (no crossover). The subwoofer channel crossover is low pass only. The cutoff frequencies are variable, and can be set between 32Hz and 320Hz using the rotary controls. The crossovers have a 12dB per octave slope. A small screwdriver is required to adjust the frequency.
Dynamic Bass Optimizer (DBO): The amplifier's DBO circuit features a 0-12dB bass boost. In addition, a subsonic filter helps prevent the amplifier from wasting power by eliminating ultra-low frequencies you can't hear. You can adjust the filter between 10Hz and 80Hz. A small screwdriver is required to adjust the bass boost and subsonic frequency controls.
Phase: You can set the subwoofer phase at 0° or 180°. While playing music with lots of bass, slide the phase switch back and forth. Choose the setting that provides more bass. If there is little difference, leave the switch at 0°.
Auto Turn-on: If your stereo does not have a "Remote Out" wire, you can set the amplifier to automatically turn on when it detects a speaker level signal on the input. If you are connecting a remote turn-on lead, the switch should be left in the "off" position.
Terminals: The Infinity Kappa Five uses set screw terminals for the +12V power, ground, remote turn-on, and speaker outputs. The terminals are located under a magnetic cover, which can easily be pried off to access the screw heads. The screws can be tightened/loosened with a Phillips-head screwdriver (not provided).
Power/Ground: The +12V Power and Ground terminals will accept up to 4-gauge wire. It is recommended that you use a minimum of 4 AWG power wire to the battery, with an in-line 100A fuse installed no more than 18" from the battery terminal. A 4 AWG ground wire (minimum) is also recommended, and attached to a metal area close to the amplifier.
E.A.R.L. Terminal: An Electrical Anti-Rotational Locking (E.A.R.L.) terminal is provided for the ground wire. The terminal is designed for 1/0 AWG ground wire, and requires a large crimping tool to secure the wire. The terminal includes 3 screws to attach the terminal to your vehicle's metal chassis.
Remote Turn-On: The Remote screw terminal will accept up to 8 AWG wire. Typically, an 18 AWG turn-on lead is included in an amplifier wiring kit.
Power/Ground Adapter: If you wish to use power and ground wire larger than 4 AWG, you can use the included plug-in adapter. The adapter has posts that insert into the +12V, REM, and GND terminals and offers 1/0 AWG power and ground terminals. An 18 AWG screw terminal for the remote turn-on wire is also provided.
Speaker Outputs: The amp features set screw terminals for connecting four speakers and one subwoofer. The amplifier's minimum speaker impedance is 2 ohms.
Line-Level Inputs: The amplifier is equipped with three pair of RCA inputs for connecting stereo RCA patch cables from the head unit to the amp.
Speaker-Level Input: The amp includes six speaker-level adapters (bare wire-to-RCA) for connecting the amp to a factory radio or aftermarket head unit. You should insert the speaker wires from the head unit into the adapters and plug the adapters into amp's RCA inputs.
Remote Level Control: An RJ-25 modular "phone" jack is provided for connecting the Remote Level Control cable.