About the Infinity Primus 3000A
Add bass power
Add bass power
If you want great power for the subwoofer in your vehicle without emptying your bank account, Infinity's Primus 3000A 1-channel subwoofer amplifier may be just what you're looking for. This little powerhouse will send your sub up to 300 watts RMS, giving you lots of low-frequency fun.
Works in almost any vehicle
Speaker-level inputs allow this amplifier to work with almost any system, even if you're keeping your factory radio. A low-pass filter and a variable phase control help maximize your subwoofer's performance. The amp also features a fully adjustable bass boost so you can make your subwoofer sound its best.
Primus 3000A input and control panel
- mono subwoofer amplifier
- 300 watts RMS x 1 at 2 ohms ( 4-ohm rating unavailable)
- variable low-pass filter (32-320 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 40-100 Hz)
- variable phase adjustment (0-180°)
- preamp and speaker-level inputs
- fuse rating: 15A x 2
- wiring and hardware not included with amplifier
- 8-gauge power and ground leads recommended
- 9-9/16"W x 2-1/16"H x 5-3/4"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # PRIMUS 3000A
What's in the box:
- Mono amplifier
- Four 15A ATO fuses (2 installed)
- 12" Speaker-level input harness (5-pin Molex plug)
- Four M4 x 30mm self-tapping screws
- 4 Flat washers
- 4 Split lock washers
- 4 Plastic screw sleeves
- 4 Plastic spacers
- Owner's Manual
Thanks for submitting your review
More details on the Infinity Primus 3000A
Features & specs
|RMS Power Output (Watts x Channels)|
|Peak Power Output (Watts x Channels)||600 x 1|
|Power at 2 Ohms (Watts x Channels)||300 x 1|
|Bridged Power (Watts x Channels)||---|
|Minimum Impedance Bridged||---|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||10-320 Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||75 dB|
|Low-Pass Crossover Frequency||32-320 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||40-100 Hz|
|Speaker Level Inputs||---|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Power Output: The Infinity Primus 3000a monoblock amplifier delivers 300 watts RMS to a 2-ohm load, and 600 watts total peak power. No 4-ohm power spec is provided.
Protection Circuitry: The amplifier features protection circuitry for thermal overload, DC voltage on the audio output, over- or under-voltage (<9V or >16V), and short circuits. The LED on the end of the amp glows red if the amp goes into protection mode.
Gain: The Primus 3000a's rotary gain control let you match the amp's input sensitivity to the output of the source unit. The input sensitivity range of the amplifier 0.2V - 5V for a line-level input, and 0.5V - 12V for speaker-level input. A small screwdriver (not included) is required to set the gain.
Crossover: The amp features a low-pass filter that is non-defeatable. It eliminates a range of high frequencies that are sent to the subwoofer. You can adjust the cutoff frequency of the low-pass filter from 32Hz to 320Hz using the rotary control. A small screwdriver is required to adjust the frequency.
Phase: The Primus 3000a features a continuously variable phase control, adjustable from 0° to 180°. While playing bass-heavy music, you should turn the phase control until you find the setting that provides the most bass. If you don't detect any real difference, leave the setting at 0°.
Bass EQ: The amplifier's Bass EQ circuit lets you increase the bass output from 0dB to 12dB. You can also choose the center frequency of the bass boost. This setting is continuously variable from 40Hz to 100Hz.
Terminals: The Infinity Primus 3000a uses screw terminals for the +12V power, ground, turn-on (remote) lead, and speaker outputs. The screws can be tightened/loosened with a Phillips-head or flat-head screwdriver (not provided).
Power/Ground: The +12V Power and Ground terminals will accept up to 4-gauge wire. It is recommended that you use a minimum of 8 AWG power wire to the battery, with an in-line 30A fuse installed no more than 18" from the battery terminal. An 8 AWG ground wire (minimum) is also recommended, and attached to a metal area close to the amplifier.
Remote Turn-On: The Remote screw terminal will accept up to 8 AWG wire. Typically, an 18 AWG turn-on lead is included in an amplifier wiring kit.
Speaker-Level Input: The amp includes a 12" speaker-level input harness for connecting the amp to a factory radio or aftermarket head unit. You should splice left and right speaker wires from the head unit to the harness and plug the harness into the amp.
Line-Level Inputs: The amplifier is equipped with one pair of RCA inputs for connecting stereo RCA patch cables from the head unit to the amp. If your source unit only has one subwoofer output, you can connect it to either the left or right RCA inputs on the amp.
Speaker Outputs: The amp features screw terminals for connecting one speaker. The amplifier's minimum speaker impedance is 2 ohms, so you can connect any combination of speakers that presents a 2 ohm load or higher.