Chat
Contact us
Close contact box
Connect ID #
095 286 473 3
Connect ID #
095 286 473 3
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

JBL BassPro Nano

Compact powered subwoofer with 6"x8" sub and 100-watt amp

Item # 109BASPRON

The BassPro Nano gives you the low end you're looking for in a package that'll fit almost anywhere.

The BassPro Nano gives you the low end you're looking for in a package that'll fit almost anywhere.

In stock
$229.95

About the JBL BassPro Nano

Compact bass for your compact space

Today's compact powered subwoofers have brought the pleasures of great bass to smaller spaces than ever before, but there are still places a typical compact sub won't fit. JBL's BassPro Nano gives you 100 solid watts of RMS power in a 10" x 8" x 3" enclosure that fits under almost any seat. A specially-designed shallow-profile 6"x8" woofer gives the BassPro Nano the impact of a larger speaker while saving valuable space. The die-cast anodized aluminum enclosure and metal grille protect the speaker from accidental damage.

Compact bass for your compact space

Today's compact powered subwoofers have brought the pleasures of great bass to smaller spaces than ever before, but there are still places a typical compact sub won't fit. JBL's BassPro Nano gives you 100 solid watts of RMS power in a 10" x 8" x 3" enclosure that fits under almost any seat. A specially-designed shallow-profile 6"x8" woofer gives the BassPro Nano the impact of a larger speaker while saving valuable space. The die-cast anodized aluminum enclosure and metal grille protect the speaker from accidental damage.

Control over your bass

The low-pass filter, adjustable bass boost, and phase switch help you dial in your sound. Line- and speaker-level inputs with switchable load give you multiple options for wiring your system. The included wiring harness simplifies installation, and a wired remote control lets you adjust the sub's volume from the driver's seat. When you need to bring modern bass response to the cramped spaces of today's vehicles, the BassPro Nano delivers great sound in an easy-to-fit package.

READ LESS

Product highlights:

  • powered subwoofer with die-cast aluminum enclosure
  • 6"x8" shallow-profile woofer
  • built-in amplifier: 100 watts RMS (200 watts peak)
  • controls:
    • low-pass crossover variable from 50-150 Hz at 12 dB per octave
    • variable bass boost (0 to +12 dB at 50 Hz)
    • phase switch (selectable 0 or 180 degrees)
    • wired remote volume control
  • speaker and line-level inputs
  • frequency response: 30-150 Hz
  • dimensions: 7-11/16"W x 2-15/16"H x 10-1/4"D
  • warranty: 1 year
  • Our 60-day money-back guarantee
  • MFR # SUBBPNANOAM

What's in the box:

  • Powered 6x8" subwoofer (15A ATC fuse installed)
  • Remote level control
  • 16.5' Remote cable (RJ-25 connectors on both ends)
  • 12" Input harness
  • Spare 15A ATC fuse
  • 4 Mounting plates
  • Four 1" screws
  • Two 1/2" screws
  • Eight 1/4" screws
  • Owner's manual

Featured video:

Customer reviews

Loading reviews...

JBL BassPro Nano reviews

Average review:

57 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the JBL BassPro Nano

Pat M.

Features & specs

General
Enclosure Type Sealed
Finish Material Die-cast aluminum
Grille Aluminum
Connector Type Molex plug, RCA
Bi-amp Inputs No
Woofer Size (inches) 6x8
Woofer Material Not given
Passive Radiator None
Width 7-1/2"
Height 3"
Depth 10-1/4"
Second Depth N/A
Parts Warranty 1 Year
Labor Warranty 1 Year
Specifications
Frequency Response 30-150
Amplifier Power (RMS) 100 watts
Maximum Wattage 200 watts
Sensitivity ---
Impedance ---
Second Voice Coil Impedance ---
Crossover Point 50-150

Product Research

Features

Enclosure & Driver: The JBL BassPro Nano features a single 6x8" woofer in a sealed enclosure that's compact enough for mounting under seats and in tight spaces.

Amplifier: The subwoofer enclosure is powered by a built-in 100 watt RMS Class-D amplifier. Class-D operation means the amp runs cooler and draws less current from the vehicle's electrical system.

High/Low Inputs: The BassPro Nano includes a pair of RCA low-level signal inputs, accepting signals from 0.1V - 4.0V. If connecting to a factory headunit or radio without pre-amp outputs, 2-channel speaker-level input wiring is included, accepting signals from 0.25V - 10V.

Audio Sense: The Auto Turn-On button, when set to On, allows the BassPro Nano to power on when it senses voltage on the speaker-level inputs, eliminating the need for connecting a remote turn-on wire.

Crossover: The amplifier's low-pass crossover point is continuously variable from 50 to 150 Hz; the crossover slope is 12 dB/octave.

Bass Boost: The bass boost circuit provides a variable (0-12dB) signal boost centered at 50Hz.

Remote Level Control: A remote level control is provided, that can be mounted under a dash or console for easy adjustment of the bass level from the driver's location. The remote level control includes a 16.5' remote cable terminated in RJ-25 connectors on both ends.

Mounting: The JBL BassPro Nano includes 4 mounting plates and hardware for installing the subwoofer under seats, rear truck cabs, trunks, or any location where space is tight.

Additional Controls&Indicators:

  • Phase: A push-button switch (0° or 180°) allows the subwoofer's phase to easily be inverted .
  • Gain: A rotary knob adjusts the input signal level.
  • Power LED: Lights to indicate unit is powered on.
  • Protect LED: Lights to indicate a fault or short-circuit.

Connections:

  • Remote Bass: RJ-25 jack for use with included remote bass level control.
  • Fuse: A single 15 amp ATC fuse protects the amplifier.
  • Input Harness: A 12", 10-pin input harness includes: Power and Ground (12 AWG), a Remote Input wire, and Left&Right High Level Input wires.

Loading accessories...

Customer Q&A

10 questions already asked

Q
Can this be mounted upside down?
[ J  Nov 25, 2020 ]
1 answer
A
I would say yes. If you mean under a seat, I have an 07 Subaru Outback and it doesn't really fit under the seat. Check dimensions.
[ Tanielu  Nov 25, 2020 ]
Q
Can I use an 8 gauge amp wiring kit? Mainly is it safe to splice 8 gauge power to the 14 gauge wire on the Nano's loom? What's the best way to step between the two wires or Is it better to use a smaller wire?
[ Chris  Oct 01, 2020 ]
2 answers
A
No reason you cant go from 8 ga to 14ga like that, Actually the more, and longer run of thicker ga cable you can use the better. You will have less voltage drop that way, not that the Nano is a high power draw though. You just need a way to physically connect the 8ga to the 14ga wire. You can solder it. Or maybe use a small distribution block.
[ John  Oct 01, 2020 ]
A
Sure you can. Just take care and do a good job on your splice and insure that you put a fuse on the positive side of the circuit close to your battery. Try to keep power wires away from speaker wiring due to the RF from the power wires. If you run power wires next to speaker wiring you could end up with a whine that you can hear through your speakers that will change pitch with the RPM of the engine. Hope this helps
[ SHANE  Oct 01, 2020 ]
Q
How do you power this, what gauge do you connect to the harness?
[ Ali  Aug 22, 2020 ]
3 answers
A
I would use nothing smaller than 12 gauge wire for power.
[ David  Aug 24, 2020 ]
A
I used12 gauge wire and ran directly from the battery. Make sure to use a fuse at the battery, fuse is 20 amp.
[ charles  Aug 22, 2020 ]
A
I used the Crutchfield CK12 kit.
[ Chris  Aug 22, 2020 ]
Q
I have a 1998 grand cherokee with the infinity gold sound system, I upgraded to pioneer door speakers and head unit and with crutchfields harness the factory amp and dash speakers work as well. How would I install this subwoofer with my current setup?
[ Marc  Jun 21, 2020 ]
4 answers
A
Hope to answer your question; On my honda truck this sub was installed by someone I know for while, because I was afraid to burn it, the fairest they explain to me, was connected on the wiring from the speakers on the head unit, Sorry for don't help on this matter,
[ Oscar  Jul 07, 2020 ]
A
I recently installed a pioneer head unit, door speakers, dash speaker, and this subwoofer. First and foremost, I hope you didn't fall prey to the quick connect RCA plugs on the subwoofer and / or the head unit. They wont power the speakers. Hardwire everything. In this case, run the red positive wire to the battery. Run the black wire to a bolt to ground it. Run the volume / on / off cable to wherever you want to quickly adjust it. For me, I ran the speaker wires from the subwoofer to the head unit and connected it with the rear left an right speakers. That may not be the best speakers to add it to, but it worked for me and sounds very good. Hope this helps.
[ Tj  Jul 06, 2020 ]
A
Is your factory amp able to push the power those infinity door speakers need? If not I would recommend doing a duel amp wiring kit and running power for both a 4 channel amp and this sub. The basspro nano is a very good system, but is only good if it is in the main cabin under a seat. It will have a very hard time going from the trunk all the way to the driver seat. It is not powerful enough for that.
[ JOHN  Jul 06, 2020 ]
A
Just follow up the manufacturer installation directions. Set up is very easy. Also, don't forget Crutchfield'sTech support. They can help you with any questions 24/7. Hope this helps!
[ Vladimir  Jul 06, 2020 ]
Q
I have a 2018 GMC Sierra that has cables to connect a sub under the seat, is there a kit that can be used to connect this subwoofer at this same location? The wiring is from the factory and designed to connect a kicker amp and subwoofer that is sold by GMC.
[ Victor  Jun 19, 2020 ]
1 answer
A
The JBL basspro nano comes with line and speakers level inputs you probably can use the factory wires for input There should be a power,ground and remote wire from the factory since it was designed to connect an amp and subwoofer
[ eric  Jun 19, 2020 ]
Q
I have a 2006 Jeep Wrangler with center console sub. Can I hook this up off of the existing sub and have both or is it one or the other?
[ Glenn  Jun 16, 2020 ]
2 answers
A
If the exiting sub is powered then no you can't take that amp powered signal. But you can take the signal pre amp and use that for this sub to run both. Usually if a signal is split like that it gets a little weaker. The JBL has adjustable gain so you can even out with the existing sub or not depending on the two subs sizes you can cover more Hz range.
[ Binh  Jun 16, 2020 ]
A
Not sure if this will ensure success for you, but I did something similar with the small "sub woofer" in the center console of my 1997 Lexus LX450 (Land Cruiser). It has a 4" factory-mounted sub in center console and I was able to fit the BassPro Nano in the center console and still use the existing factory sub as well. However, that required me to stick with the factory amp, which I will likely be ditching in favor of a more powerful aftermarket amp. Anyway, the JBL BassPro Nano is plenty powerful enough for my needs, so I won't mind losing the small factory sub when I upgrade the amp. I am very happy with the JBL! It really brought the system to another level.
[ PAUL  Jun 16, 2020 ]
Q
Can two or more units be connected together and still controlled by one remote?
[ Ray  Jun 16, 2020 ]
2 answers
A
There is a wired volume control that plugs into amp. It cannot control any other sub. You would need an external control before the audio is split to run more than one sub.
[ David  Jun 16, 2020 ]
A
Not that I know of, the remote is hard wired.
[ Binh  Jun 16, 2020 ]
Q
Is it easy to install?
[ J  Apr 21, 2020 ]
2 answers
A
The hardest part is running the power wire from the battery into the passenger cabin. Finding a spot to snake the wire in.
[ Binh  Jun 16, 2020 ]
A
Very easy. You don't even have to remove the stereo, just take speaker inputs from one nearby speaker.
[ Chris  Apr 21, 2020 ]
Q
Can you tell me how I splice the connector to a factory DVD stereo in a 2008 Jeep Wrangler unlimited Sahara Please? (Wiring diagrams) Guess I just can't figure it out. Thanks. John O.
[ John  Apr 14, 2020 ]
2 answers
A
You would splice into the speaker wires of the factory radio. It is known as the high signal output or speaker out put.
[ Binh  Jun 16, 2020 ]
A
If you purchased the product from Crutchfield, feel free to contact our Tech Support team. Our toll-free Tech Support number is printed on your invoice, and is also available under the "My Orders" tab in the "My Account" section of our website. If you did not purchase the unit from Crutchfield, then you may want to contact the manufacturer.
[ Krissy  Apr 27, 2020 ]  Staff
Q
Can you connect 2 of these in one vehicle from the factory radio?
[ Kurt  Apr 10, 2020 ]
2 answers
A
yes, just use high level/speaker signal, left speaker for one and right speaker for other as the signal source. Factory won't have RCA/low line output.
[ Binh  Jun 16, 2020 ]
A
You sure can connect two of these to a stock radio! I recommend contacting an advisor on 1-800-324-9695 to discuss this and get all the wiring needed to install them
[ Paul  Apr 26, 2020 ]  Staff
SHOW MORESHOW LESS

Loading articles...

TOP